Toshiba G9 Installation And Operation Manual page 37

P24
PP
ACE-tronics G9 ASD Installation and Operation Manual
efesotomasyon.com -Toshiba inverter,drive,servo,plc
a motor by setting a limit. The gain and bias of this terminal may be adjusted for application-specific
suitability (see F216 – F221). See
V/I
— The V/I terminal has the dual function of being able to receive an input voltage or current. The
function as a voltage input is to receive a 0 – 10 VDC input signal. The function as a current input is to
receive a 0 – 20 mA input signal. Using either input type, the function is to control the 0.0 – Maximum
Frequency output or the 0.0 to 250% torque output of the ASD. This is an isolated input terminal. This
terminal may be programmed to control the speed or torque of the motor and cannot process both input
types simultaneously. SW2 must be set to V or I to receive a voltage or current, respectively (see
8 on pg. 24). Terminal scaling is accomplished via
be adjusted for application-specific suitability (see
P24
— +24 VDC at 200 mA power supply for customer use.
PP
— The function of output PP is to provide a 10 VDC/10 mADC max. output that may be divided
using a potentiometer or other transducer. The tapped voltage is applied to the RR input to provide
manual control of the RR programmed function.
OUT1
— The default function assigned to this terminal is Output Low Speed. This output may be
programmed to provide an indication (open or closed) that any one of the functions listed in
pg. 242 has occurred or is active. This function may be used to signal external equipment or to activate
the brake (see F130). The OUT1 terminal is rated at 2 A/120 VAC and 2 A/30 VDC.
OUT2
— The default function assigned to this terminal is ACC/DEC Complete. This output may be
programmed to provide an indication (open or closed) that any one of the functions listed in
pg. 242 has occurred or is active. This function may be used to signal external equipment or to activate
the brake (see F131). The OUT2 terminal is rated at 2 A/120 VAC and 2 A/30 VDC.
FP
— The default function of this output terminal is to output a series of pulses at a rate that is a
function of the output frequency of the ASD (50 mA max. at 1.0 kHz to 43.3 kHz). As the output
frequency of the ASD goes up so does the FP output pulse rate. This terminal may be programmed to
provide an output pulse rate that is proportional to the magnitude of any of the user-selected items from
Table 8 on pg. 240. For additional information on this terminal see
AM
— This output terminal produces an output voltage that is proportional to the output frequency of
the ASD or of the magnitude of the function assigned to this terminal. This terminal may be
programmed to provide an output voltage that is proportional to the magnitude of any of the user-
selected items from Table 8 on pg.
186.
FM
— This output terminal produces an output current or voltage that is proportional to the output
frequency of the ASD or of the magnitude of the function assigned to this terminal. This terminal may
be programmed to provide an output current or voltage that is proportional to the magnitude of any of
the user-selected items from Table 8 on pg.
pg. 81. The Voltage/Current output selection is performed at F681.
BRAKE-A
— One of two normally open contacts that, under user-defined conditions, connect to
BRAKE-C.
BRAKE-B
— One of two normally closed contacts that, under user-defined conditions, connect to
BRAKE-C.
Figure 20 on pg. 30 for an electrical depiction of the RX terminal.
F201 – F206. The gain and bias of this terminal may
F470 and F471).
240. For additional information on this terminal see
240. For additional information on this terminal see
Table 10 on
Table 10 on
F676 on pg. 188.
F670 on pg.
F005 on
Figure
27