Toshiba G9 Installation And Operation Manual page 294

efesotomasyon.com -Toshiba inverter,drive,servo,plc
OUT1/OUT2 Output, 29
OUT2, 27
Output Current, 54
output disconnect, 8
Output Function Assigned, 211, 213, 214, 218, 219, 221,
222
Output Phase Failure, 256
Output Phase Failure Detection, 177
Output Power, 55
Output Terminal 1 (OUT1) Function, 96
Output Terminal 10 (R3) Function, 101
Output Terminal 11 (R4) Function, 101
Output Terminal 2 (OUT2) Function, 96
Output Terminal 3 (BRAKE) Function, 96
Output Terminal 4 (OUT3) Function, 97
Output Terminal 5 (OUT4) Function, 97
Output Terminal 6 (R1) Function, 97
Output Terminal 7 (OUT5) Function, 98
Output Terminal 8 (OUT6) Function, 98
Output Terminal 9 (R2) Function, 98
Output Terminals, 62
Output Voltage, 54
Over-Current, 251
Over-Current During Acceleration, 257
Over-Current During Deceleration, 257
Over-Current During Run, 257
Over-Current Protection, 13
Over-Heat, 251, 257
Over-Heat During Acceleration, 257
Over-Heat During Deceleration, 258
Over-Heat During Run, 258
Overload, 65
Overload Protection, 10
Overload Reduction Starting Frequency, 177
Override Control, 73
Override mode, 49
Override Operation, 49
Over-Speed Detection Frequency Lower Band, 180
Over-Speed Detection Frequency Upper Band, 180
Over-Torque, 251, 258
Over-Torque Detection Hysteresis, 179
Over-Torque Detection Level (Negative Torque), 179
Over-Torque Detection Level (Positive Torque), 179
Over-Torque Detection Time, 179
Over-Torque Parameters, 66
Over-Torque Trip, 179
Over-Voltage, 252
Over-Voltage During Acceleration, 258
Over-Voltage During Deceleration, 258
Over-Voltage During Run, 258
Over-Voltage Limit Operation, 140
284
Over-Voltage Limit Operation Level, 181
P
P24, 27
P24 Output, 29
PA/+, 16
Panel Load Sharing Gain, 194
Panel Operation Jog Mode, 130
Panel Override Multiplication Gain, 194
Panel Stop Pattern, 193
Panel Tension Torque Bias, 194
Panel Torque Command, 193
Parameter Write Lockout, 191
Password, 78
Password and Lockout, 78
Past Trip #1, 56
Past Trip #2, 56
Past Trip #3, 56
Past Trip #4, 56
Pattern Cycle Number, 55
Pattern Group Number, 55
Pattern Preset, 55
Pattern Time, 55
PC/-, 16
Permanent Magnet (PM) Motor Constant 2, 168
PG Disconnection Detection, 154
PG Input Point 1 Frequency, 125
PG Input Point 1 Setting, 125
PG Input Point 2 Frequency, 126
PG Input Point 2 Setting, 126
PG Settings, 73
Phase Loss, 66
PID Control Switching, 150
PID Control Wait Time, 152
PID Deviation Lower Limit, 152
PID Deviation Upper Limit, 151
PID Feedback, 55
PID Feedback Delay Filter, 151
PID Feedback Differential (D) Gain, 152
PID Feedback Integral (I) Gain, 151
PID Feedback Proportional (P) Gain, 151
PID Feedback Signal, 151
PID Output Lower Limit, 153
PID Output Upper Limit, 152
Plugging, 57, 168
Plugging Acceleration Time, 174
Plugging Acceleration/Deceleration Pattern, 175
Plugging Deceleration Time, 175
PM Motor, 71, 168
ACE-tronics G9 ASD Installation and Operation Manual