Toshiba G9 Installation And Operation Manual page 252

Table 10. My Function Input Setting (Input Function Target) Assignments, and Parameter/Input Setting
Numbers for the BRAKE-A/B/C, OUT1, OUT2, OUT3–OUT6, and R1–R4 Terminals.
Input Param.
Setting Setting
1000 0
1002 2
1004 4
1006 6
1008 8
1010 10
1012 12
1014 14
1016 16
1018 18
1020 20
1022 22
1024 24
1026 26
1028 28
1030 30
1032 32
1034 34
1036 36
1038 38
1040 40
1042 42
1044 44
1046 46
1048 48
1050 50
1052 52
1054 54
1056 56
1058 58
1060 60
1062 62
1064 64
1068 68
Brake
Release
1070 70
1072 72
242
efesotomasyon.com -Toshiba inverter,drive,servo,plc
Discrete Output Terminal Assignment Selections (Positive Logic)
Function
Lower-Limit Frequency
Upper-Limit Frequency
Low Speed Signal
Acceleration/Deceleration Completion
Speed Reach Signal
Failure BRAKE (All Trips)
Failure BRAKE (Except EF, OCL, EPHO, OL2)
Over-Current (OC) Alarm
ASD Overload (OL1) Alarm
Motor Overload (OL2) Alarm
Overheat Alarm
Over-Voltage Alarm
Main Circuit (MOFF) Under-Voltage Alarm
Low-Current Alarm
Over-Torque Alarm
DBR Overload Alarm
Emergency Off Active
Retry Active
Pattern Operation Switching Output
PID Deviation Limit
Run/Stop
Serious Failure (OCA, OCL, EF, Phase Failure,
etc.)
Light Failure (OL, OC1, 2, 3, OP)
Commercial Power/ASD Switching Output 1
Commercial Power/ASD Switching Output 2
Cooling Fan On/Off
Jogging Operation Active (Jog Run Active)
Panel/Terminal (Board) Operation Switching
Bearing Greaser Run-Time Alarm
ProfiBus/DeviceNet/CC-Link Communication
Error
Forward/Reverse Switching
Ready for Operation 1
Ready for Operation 2
Brake Release (BR)
Alarm Status Active
Forward Speed Limit (Torque Control)
Input Param.
Setting Setting
1074 74 Reverse Speed Limit (Torque Control)
1076 76 ASD Healthy Output
1078 78 RS485 Communication Error
1080 80 Error Code Output 1
1082 82 Error Code Output 2
1084 84 Error Code Output 3
1086 86 Error Code Output 4
1088 88 Error Code Output 5
1090 90 Error Code Output 6
1092 92 Specified Data Output 1
1094 94 Specified Data Output 2
1096 96 Specified Data Output 3
1098 98 Specified Data Output 4
1100 100 Specified Data Output 5
1102 102 Specified Data Output 6
1104 104 Specified Data Output 7
1106 106 Switch Out Of Sequence
1108 108 Heavy Load
1110 110 Positive Torque Limit
1112 112 Negative Torque Limit
1114 114 External Rush Suppression Relay Activated
1118 118 Completion of Stop Positioning
1120 120 L-STOP
1122 122 Power Failure Synchronized Operation
1124 124 Traverse Active
1126 126 Traverse Deceleration Active
1128 128 Part Replaceme nt Alarm
1130 130 Over-Torque Alarm
1132 132 Frequency Command ½ Selection
1134 134 Failure BRAKE (Non-Emergency Off)
1136 136 External Fault
1138 138 Drooping Fault
1140 140 Run Before Ready
1142 142 Slow-Speed Limit Switch
1144 144 Stop Limit-Switch Forward
1146 146 Slow-Speed Limit Switch
ACE-tronics G9 ASD Installation and Operation Manual
Function