Table of Contents
Advertisement
Quick Links
2200 lb Shop Crane (CLHMSC-220)
4400 lb Shop Crane (CLHMSC-440)
Email:
sales@challengerlifts.com
Office 800-648-5438
IMPORTANT:
2311 South Park Rd. Louisville, Kentucky 40219
/
502-625-0700 Fax 502-587-1933
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
Web site:
www.challengerlifts.com
12/11/2023
Advertisement
Table of Contents
Related Manuals for Challenger Lifts CLHMSC-220
Summary of Contents for Challenger Lifts CLHMSC-220
- Page 1 2200 lb Shop Crane (CLHMSC-220) 4400 lb Shop Crane (CLHMSC-440) 2311 South Park Rd. Louisville, Kentucky 40219 Email: Web site: sales@challengerlifts.com www.challengerlifts.com Office 800-648-5438 502-625-0700 Fax 502-587-1933 IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT 12/11/2023...
-
Page 2: Table Of Contents
Adjusting Load Height ............................. 14 Moving the Load ..............................14 Folding Legs for Storage ............................15 Maintenance and Lubrication Instructions ........................16 Structural Inspection ................................. 17 Troubleshooting ................................19 CLHMSC-220/440 Rev. 12/11/23... -
Page 3: Signal Words
Before attempting to operate this equipment, thoroughly read and understand this manual. Completely remove all tape and packaging. Inspect the equipment immediately upon delivery. If shipping damage is evident, inform the delivering carrier immediately and contact the manufacturer using the contact information on the back cover of this manual. CLHMSC-220/440 Rev. 12/11/23... -
Page 4: Introduction
Wheel Diameter ..................6” 6” Weight ....................... 540 lbs. 640 lbs. Maximum Air Pressure (if equipped with air pump) ........ 200 psi 200 psi Minimum Air Pressure (if equipped with air pump) ........ 95 psi 95 psi CLHMSC-220/440 Rev. 12/11/23... -
Page 5: Component Identification
Pump Mounting Bracket Hydraulic Hose Boom Extension Holes Air Pump (Manual pump not shown) Boom Extension Handle Chain Air Pump Mounting Bracket Handle Wheels Leg Swivel Caster Leg Positioning Pin Wheels Right Leg Left Leg Hook Leg Positioning Holes CLHMSC-220/440 Rev. 12/11/23... -
Page 6: Assembly Instructions
2. On the opposite end of the pump [#4], insert two 3/8” X 1” bolts [#3] and start a 3/8” nut [#2] on each bolt. See Figure 1. Only start the nuts [#2] one or two turns onto the bolts [#3]. Figure 1 CLHMSC-220/440 Rev. 12/11/23... - Page 7 Conoco MV22 until the level is 2” to 3” from the bottom of the hole. 9. Install the breather vent plug [#7], provided with the crane, in the pump [#4] in the same hole the shipping plug [#6] was removed from in Step 7. Figure 3 CLHMSC-220/440 Rev. 12/11/23...
- Page 8 [#12] is attached to the pump bracket [#11] using two 5/16” X 3/4” bolts [#15] and two 5/16” lock washers [#16]. The 5/16” X 3/4” bolts [#15] thread into tapped holes in the air pump [#12]. Figure 5 CLHMSC-220/440 Rev. 12/11/23...
- Page 9 1-1/4” from the bottom of the hole. 7. Install the breather vent plug [#20], provided with the crane, in the pump [#12] in the same hole the shipping plug [#19] was removed from in Step 5. Figure 7 CLHMSC-220/440 Rev. 12/11/23...
-
Page 10: Hydraulic Cylinder Installation
5. Disconnect the hydraulic hose [#23] from the quick coupler [#22] once all the air has been purged from the cylinder. CLHMSC-220/440 Rev. 12/11/23... - Page 11 1” retaining ring [#31] into each of the Figure 11 grooves in the retaining pin. 10. Insert the hydraulic hose [#23] into the cylinder’s quick coupler [#22] and thread the quick coupler’s collar onto the hose. Figure 12 CLHMSC-220/440 Rev. 12/11/23...
-
Page 12: Operating Instructions
Operating the crane without the extension pin or with a load that exceeds capacity may result in equipment failure leading to property damage, serious personal injury, and/or death. CLHMSC-220/440 Rev. 12/11/23... -
Page 13: Adjusting The Legs
Ensure that the hook and chain assembly or other adequate load capturing device is directly above the load to be raised. Pay careful attention to how the load will react when raised. If the center CLHMSC-220/440 Rev. 12/11/23... -
Page 14: Adjusting Load Height
Before moving the crane and load, position the load at its lowest possible height. Once any height restricting obstacles (i.e. engine compartment) have been cleared by the load, stop and reposition the load to its then current lowest possible height and continue doing CLHMSC-220/440 Rev. 12/11/23... -
Page 15: Folding Legs For Storage
WARNING! Failing to properly secure the legs can cause the legs to fall unexpectedly and may result in property damage, serious personal injury, and/or death. CLHMSC-220/440 Rev. 12/11/23... -
Page 16: Maintenance And Lubrication Instructions
Inspect the condition of all decals on the crane. They should be legible and easy to read. If they become hard to read, clean with a mild soap and water solution or replace immediately. CLHMSC-220/440 Rev. 12/11/23... -
Page 17: Structural Inspection
Inspect the cylinder and cylinder rod for any signs of wear, damage, or oil leaks. The cylinder rod should be straight without any gouges, scratches, or marks. The cylinder must be free of dents, gouges, or other damage. NEVER use a cylinder that is damaged in any way. CLHMSC-220/440 Rev. 12/11/23... - Page 18 ONLY use repair parts supplied by the manufacturer to repair this crane. NEVER use spare parts from other sources; they may not be designed to be used on this crane or rated at the same capacity. CLHMSC-220/440 Rev. 12/11/23...
-
Page 19: Troubleshooting
Cylinder Installation” section to purge the air from the cylinder. The cylinder will need to be removed from the crane, purged, and then reinstalled as described in the “Hydraulic Cylinder Installation” section to properly remove the air. CLHMSC-220/440 Rev. 12/11/23... - Page 20 Model CLHMSC-220/440 P.N. 670-90557...