Table of Contents
Advertisement
Quick Links
Installation, Operation & Maintenance Manual
CLHM-MR20
Email:
Office 800-648-5438
IMPORTANT:
Wheel Lift System
M
ODEL
AND
10,000
./ 15,000
LBS
LBS
20,000
./ 30,000
LBS
LBS
2311 South Park Rd Louisville, Kentucky 40219
sales@challengerlifts.com
/
502-625-0700 Fax 502-587-1933
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
CLHM-MR30
. C
APACITY PER LIFT
.
LIFT SYSTEM CAPACITY
Web site:
www.challengerlifts.com
Rev. 09/19/2019
Advertisement
Table of Contents
Related Manuals for Challenger Lifts CLHM-MR20
Summary of Contents for Challenger Lifts CLHM-MR20
- Page 1 Installation, Operation & Maintenance Manual Wheel Lift System ODEL CLHM-MR20 CLHM-MR30 10,000 ./ 15,000 APACITY PER LIFT 20,000 ./ 30,000 LIFT SYSTEM CAPACITY 2311 South Park Rd Louisville, Kentucky 40219 Email: Web site: sales@challengerlifts.com www.challengerlifts.com Office 800-648-5438 502-625-0700 Fax 502-587-1933...
- Page 2 Model MR20 AND MR30 Installation, Operation and Maintenance ENERAL PECIFICATIONS CLHM MR20 CLHM MR30 Maximum Capacity, each lift 10,000 lbs 15,000 lbs Maximum Capacity, system 20,000 lbs 30,000 lbs Maximum Air Pressure 160 psi Minimum Wheel Dia w/o Adapters 19” Minimum Wheel Dia with Adapters 16”...
-
Page 3: Receiving Inspection
Model MR20 AND MR30 Installation, Operation and Maintenance Receiving Inspection Before attempting to operate this system, thoroughly read and understand this manual. Inspect the jacks immediately upon delivery. If shipping damage is evident, inform the delivering carrier immediately and contact the manufacturer using the contact information on the back cover of this manual. Introduction Owner and / or Operator Responsibilities The owner and / or user must have an understanding of the manufacturer’s operating instructions and... - Page 4 Model MR20 AND MR30 Installation, Operation and Maintenance Location of the Load Retention Pin varies by model. Page 4 Rev 09/19/2019 CLHMR20-IOM-A.doc...
-
Page 5: Safety Instructions
Model MR20 AND MR30 Installation, Operation and Maintenance Safety Instructions To avoid serious injury or death, read this manual carefully before operating this system. Contact the manufacturer using the contact information on the back cover of this manual if you have any questions. Failure to understand and obey safety instructions may result in unsafe or improper use of this product. -
Page 6: Optional Adapters
Model MR20 AND MR30 Installation, Operation and Maintenance Optional Adapters To prevent serious injury or death from a falling vehicle, use MR-Adapters only for vehicles with rims between 16" and 19" in diameter. Install the MR-Adapters with both hooks in the holes of the lift pad. Proper installation is shown in figure Make sure the wheel rims on the vehicle to be raised are a minimum of 19"... -
Page 7: Preparing The Lifts And Vehicle
Model MR20 AND MR30 Installation, Operation and Maintenance Operating Instructions Figure 2 Lift table tube identification. Preparing the Lifts and Vehicle To prevent serious injury or death from a falling vehicle, make sure the vehicle’s rims are at least 19 inches in diameter (or 16"... -
Page 8: Raising A Vehicle
Model MR20 AND MR30 Installation, Operation and Maintenance Raising A Vehicle To prevent serious injury or death from a falling vehicle, operate both air control levers at the same time and keep the vehicle level as it is raised or lowered. 1. - Page 9 Model MR20 AND MR30 Installation, Operation and Maintenance Lowering a Vehicle to the Ground To prevent serious injury or death from a falling vehicle, operate both air control levers at the same time and keep the vehicle level as it is raised or lowered. To prevent serious injury or death, clear the work area of all tools and equipment.
-
Page 10: Using The Lifts With Support Stands
Model MR20 AND MR30 Installation, Operation and Maintenance Using the Lifts with Support Stands Transferring a Load to Support Stands To prevent serious injury or death from a falling vehicle, never put any part of your body under a vehicle supported by Lift system unless the lifts have the load retention pins properly inserted to pin the lifts as stands. -
Page 11: Removing Support Stands
Model MR20 AND MR30 Installation, Operation and Maintenance Removing Support Stands 1. Move the lifts into place at opposite ends of the axle to be lowered and position them so the lift pads will cradle the tires when contact is made. 2. -
Page 12: Maintenance Instructions
Model MR20 AND MR30 Installation, Operation and Maintenance Maintenance Instructions To prevent serious injury or death from a falling vehicle, all inspection and maintenance procedures must be performed after the jack has been removed from service. Position the lifts so you have clear access to all sides of the lift for inspection and service. - Page 13 Model MR20 AND MR30 Installation, Operation and Maintenance Occasionally, pieces of rust, scale or dirt from the air lines may become lodged under the rubber seals of the air control unit. This may cause minor air leakage and the lift system units may slowly raise or lower even though the air control levers have not been actuated.
-
Page 14: Structural Inspection
Model MR20 AND MR30 Installation, Operation and Maintenance Structural Inspection To prevent serious injury or death from a falling vehicle, all inspection and maintenance procedures must be performed after the jack has been removed from service. Position the lifts so you have clear access to all sides of the lift for inspection and service. -
Page 15: Troubleshooting
Model MR20 AND MR30 Installation, Operation and Maintenance Troubleshooting This section is a list, in which may be encountered and their solutions. If the solution listed fails to correct the problem, contact the manufacturer using the contact information on the back cover of this manual. Please have the model number, and serial number of your jack available.