Advertisement
Table of Contents
- 1 Specifications
- 2 Vertical Clearance
- 3 Electrical Requirements
- 4 Safety Notices and Decals
- 5 Lock Release
- 6 Arm Installation
- 7 Owner /Operator Checklist
- 8 Operation Procedure
- 9 Owner /Employer Responsibilities
- 10 Lifting a Vehicle
- 11 Loweringa Vehicle
- 12 Maintenance
- 13 Parts Breakdown
- Download this manual
V
200 Cabel Street, P.O. Box 3944 Louisville, Kentucky 40201-3944
Email:
Office 800-648-5438
IMPORTANT:
IMPORTANT:
IMPORTANT:
IMPORTANT:
I I I I
NSTALLATION
NSTALLATION
NSTALLATION
NSTALLATION
& M
& M
& M
& M
AINTENANCE
AINTENANCE
AINTENANCE
AINTENANCE
ersymmetric
Surface Mounted Lift
M
ODEL
9,000
LBS
2250
sales@challengerlifts.com
/
502-625-0700 Fax 502-587-1933
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
, O
, O
, O
, O
Two Post
TM
CL9
. C
APACITY
.
A
LBS
PER
RM
Web site:
www.challengerlifts.com
PERATION
PERATION
PERATION
PERATION
M M M M
ANUAL
ANUAL
ANUAL
ANUAL
Rev. 10/9/03
A1151.doc
Advertisement
Table of Contents
Related Manuals for Challenger Lifts Versymmetric CL9
Summary of Contents for Challenger Lifts Versymmetric CL9
- Page 1 I I I I NSTALLATION NSTALLATION PERATION PERATION NSTALLATION NSTALLATION PERATION PERATION & M & M & M & M M M M M AINTENANCE AINTENANCE AINTENANCE AINTENANCE ANUAL ANUAL ANUAL ANUAL ersymmetric Two Post Surface Mounted Lift ODEL 9,000 APACITY 2250 200 Cabel Street, P.O.
-
Page 2: Specifications
Model CL9 Installation, Operation and Maintenance ENERAL PECIFICATIONS See Figure 1 CL9-1 CL9-2 11’-8” or 11’-2” 12’-8” or 12’-2” 13’-8” or 13’-2” Adjustable Column Height 11’-2” or 10’-8” 12’-2” or 11’-8” 13’-2” or 12’-8” Floor to Overhead Switch 74 5/8” Rise Height (Screw Pads Highest Position) 11’-11”... -
Page 3: Vertical Clearance
Model CL9 Installation, Operation and Maintenance Safety decals similar to those shown here are ERTICAL LEARANCE found on a properly installed lift. Be sure that all Check the height of the area where the lift is to safety decals have been correctly installed on the be installed. - Page 4 Standard open end wrenches 7/16”, 1/2", the shorted or damaged goods. Do this for your (2) 9/16”, (2) 11/16”, 3/4" own protection. g. 5/16” allen wrench Challenger Lifts NOTIFY AT ONCE if any h. Needle nose pliers hidden loss or damage is discovered after Hammer drill with 3/4”...
- Page 5 Model CL9 Installation, Operation and Maintenance 8) Shim both columns to plumb using the shims 13) Install Overhead Limit Switch to Power provided as shown in Fig 2. DO NOT shim Column using (1) 3/8” pivot pin, (1) 3/8” flat more than 1/2"...
- Page 6 Model CL9 Installation, Operation and Maintenance 15) Assemble the sheaves, spacers and washers onto the sheave pin as shown in Fig 5. Set in cradle with all assembly parts between the two plates. SHORT SHEAVE SPACER SHORT SHEAVE SPACER SHORT SHEAVE SPACER SHORT SHEAVE SPACER WASHER WASHER...
- Page 7 Model CL9 Installation, Operation and Maintenance YNCHRONIZER ABLE DJUSTMENT BULKHEAD BRANCH TEE BULKHEAD BRANCH TEE BULKHEAD BRANCH TEE BULKHEAD BRANCH TEE MALE #6 (9/16-18) MALE #6 (9/16-18) MALE #6 (9/16-18) MALE #6 (9/16-18) This method requires adjusting the cable SAE (JIC) 37° FLARE SAE (JIC) 37°...
-
Page 8: Lock Release
Model CL9 Installation, Operation and Maintenance 27) Route hydraulic hose from Idler column ELEASE across Overhead to the Power Column and 30) Attach Mechanical Lock Release Cable down inside of Power Column (routing is Assembly to Power Column Lock Release identical to Idler Column) to male #6 JIC Clevis using the 3/16”... -
Page 9: Arm Installation
Model CL9 Installation, Operation and Maintenance INAL DJUSTMENTS YDRAULICS 40) Lower the lift to the floor and raise the lift approximately one foot. 41) Start with Idler side first. Slowly and carefully loosen the bleed plug on top of the cylinder just enough to allow the entrapped air to escape. - Page 10 Model CL9 Installation, Operation and Maintenance Wiring Diagram Wiring Diagram Wiring Diagram Wiring Diagram * After wiring has been completed, test operation of Power Unit & Overhead Limit Switch. While raising * After wiring has been completed, test operation of Power Unit & Overhead Limit Switch. While raising * After wiring has been completed, test operation of Power Unit &...
-
Page 11: Owner /Operator Checklist
Owner/Employer shall establish questionnaires to: procedures to periodically maintain the lift in Challenger Lifts, Inc. accordance with lift manufacturer’s instructions or ANSI/ALIOIM-2000, American 200 Cabel Street National Standard for Automotive Lifts-Safety Louisville, KY. -
Page 12: Lifting A Vehicle
Replace as required with genuine above the desired working height. Challenger Lifts parts. 5) Lower the vehicle until the safety latches on • Check lock release cable adjustment per both columns engage. -
Page 13: Parts Breakdown
Replace all worn or broken parts with genuine Challenger Lifts Inc. parts. Contact your local Challenger Lifts Parts Distributor for pricing and availability. (Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area) Page 13 Rev. 10/9/03... - Page 14 Replace all worn or broken parts with genuine Challenger Lifts Inc. parts. Contact your local Challenger Lifts Parts Distributor for pricing and availability. (Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area) Page 14 Rev. 10/9/03...
- Page 15 Replace all worn or broken parts with genuine Challenger Lifts Inc. parts. Contact your local Challenger Lifts Parts Distributor for pricing and availability. (Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area) Page 15 Rev. 10/9/03...
- Page 16 Replace all worn or broken parts with genuine Challenger Lifts Inc. parts. Contact your local Challenger Lifts Parts Distributor for pricing and availability. (Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area) Page 16 Rev. 10/9/03...
- Page 17 Replace all worn or broken parts with genuine Challenger Lifts Inc. parts. Contact your local Challenger Lifts Parts Distributor for pricing and availability. (Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area) Page 17 Rev. 10/9/03...