Related Manuals for LinMot MagSpring MS01
Summary of Contents for LinMot MagSpring MS01
- Page 1 Installation Guide MagSpring MS01 NTI AG / LinMot Dok. Nr. 0185-0018-E_2V3_IG_MagSpring_MS01...
-
Page 2: Table Of Contents
Inserting the slider into the stator ....................11 Zero position of the slider and start position of the constant force ..........11 Mounting the Stator ......................... 13 4.7.1 MagSpring MS01-20 and MS01-37 ..................... 13 4.7.2 MagSpring MS01-40-SSC ......................14 Mounting the slider .......................... 15 Compensation of angular misalignment by spherical washers and conical seats ...... - Page 3 Installation Guide MagSpring 7.1.2 M01-37 stator series ........................23 7.1.3 MS01-40-SSC stator series ......................23 Mechanical dimensions standard slider ................... 24 Mechanical dimensions slider for linear rotary motors ..............24 NTI AG / LinMot MS01 Page 3 / 25...
-
Page 4: General Information
1.4 Liability NTI AG (as manufacturer of LinMot and MagSpring products) excludes any liability for itself and its employees for damages and expenses caused by incorrect use of the products. This also applies to incorrect applications caused by NTI AG's own information and instructions, for example in the course of sales, support or application activities. -
Page 5: Safety Instructions
For non-anti-magnetic clocks, double the minimum distance applies. Flammability When mechanically machining neodymium magnets, the drilling dust can easily ignite. It is not permitted to work on runners and the magnets they contain. NTI AG / LinMot MS01 Page 5 / 25... - Page 6 • Keep large magnets at least one metre away from your body. Temperature resistance Keep the sliders away from open flame and heat. At temperatures above 80°C the slider is demagnetised. Page 6 / 25 MS01 NTI AG / LinMot...
-
Page 7: Intended Use
Efficient element for load compensation in vertical applications, without the need for compressed air or energy through electricity. • Application of a basic force (working point force) in the resting position. NTI AG / LinMot MS01 Page 7 / 25... -
Page 8: Mounting Options Depending On Functional Requirements
The position of the MagSpring on the guide unit depends on the desired stroke range. 3.3.1 MagSpring Stators MS01-20 und MS01-37 For MagSpring MS01-20 and MS01-37 stators, special attention must be paid to the parallel alignment of the MagSpring in relation to the linear unit. -
Page 9: Magspring Stators Ms01-40 Ssc
With factory-fitted MagSpring stators of the MS01-40 SSC series, the MagSpring is always oriented towards the load. The result is a retraction movement of the moving part. Mounting on an SM guide generate a retracting movement NTI AG / LinMot MS01 Page 9 / 25... -
Page 10: Installation Instructions
If the slider's anti-twist device becomes loose, this can cause a sudden reversal of force. • With Force-Extended Series MagSprings, exceeding the maximum stroke can result in an abrupt reversal of force. 4.4 Material data MagSpring MS01-20 and MS01-37 Component Material Stator Iron, chemical nickel plated Slider Stainless steel 1.4301... -
Page 11: Inserting The Slider Into The Stator
At a distance of 35 mm from the end of the stator is the Starting Position of the constant force (SP). NTI AG / LinMot MS01 Page 11 / 25... - Page 12 The constant force start position (SP) indicates the start of the constant force range (measured 35 mm (1.38 in) from the four-edged working end of the slider to the end of the stator). Page 12 / 25 MS01 NTI AG / LinMot...
-
Page 13: Mounting The Stator
Installation Guide MagSpring 4.7 Mounting the Stator 4.7.1 MagSpring MS01-20 and MS01-37 The MagSpring stators MS01-20 und MS01-37 can be mounted via a clamp. Suitable mounting flanges are available for both sizes. The stator must not be deformed by the clamping! -
Page 14: Magspring Ms01-40-Ssc
Installation Guide MagSpring 4.7.2 MagSpring MS01-40-SSC The MagSpring MS01-40-SSC stators are mounted on the front with a suitable mounting flange over all lengths. This provides a form-fit mounting option. Note the tightening torque of the screws: M = 4.5 Nm. -
Page 15: Mounting The Slider
(see following illustrations). • The tightening torque for the M5 screw on the slider is 4.5 Nm. Incorrect assembly Correct M = 4,5 Nm assembly NTI AG / LinMot MS01 Page 15 / 25... -
Page 16: Compensation Of Angular Misalignment By Spherical Washers And Conical Seats
10.5 mm 10.5 mm 9.5 mm 0.5 mm 2.0 mm 2.1 mm 3.2 mm (0.20 in) (0.24 in) (0.41 in) (0.41 in) (0.37 in) (0.02 in) (0.08 in) (0.08 in) (0.13 in) Page 16 / 25 MS01 NTI AG / LinMot... -
Page 17: Ordering Information For Fixed Bearing Set
No separate sale. The ring is offered and delivered with the modules. Function: The clearance ring allows for minimal movement (0.05 - 0.2 mm) along the longitudinal axis between the MagSpring and the corresponding guide. NTI AG / LinMot MS01 Page 17 / 25... -
Page 18: Minimum Distances For Magspring Sliders
MagSpring sliders and other magnetic components must be taken into account in the design. The latter include permanent magnetic parts, such as other MagSpring sliders and LinMot sliders or ferromagnetic elements made of iron or steel. 4.11.1 Minimum distances to ferromagnetic parts Minimum distance “d”... -
Page 19: Minimum Distances To Linmot Motors
MagSpring 4.11.2 Minimum distances to LinMot motors A minimum distance must also be taken into account between MagSpring sliders and LinMot motors. Forces can arise both between the two sliders and between the MagSpring slider and LinMot stator. Minimum distance “d” from the MagSpring axis to the axis of the LinMot linear motor... -
Page 20: Minimum Distances To Magsprings
60 mm (2.36 in) 66 mm (2.60 in) ML01-12x290/240... 60 mm (2.36 in) 68 mm (2.68 in) 72 mm (2.83 in) ML01-12x370/320... 64 mm (2.52 in) 74 mm (2.91 in) 80 mm (3.15 in) Page 20 / 25 MS01 NTI AG / LinMot... -
Page 21: Maintenance And Inspection Instructions
Clean the slider and stator with soft disposable paper, ideally with the aid of LU06 cleaning spray (alternatively methylated spirits or alcohol). Do not use cleaning fluids containing solvent additives, petroleum or similar products. NTI AG / LinMot MS01 Page 21 / 25... -
Page 22: Detergent / Lubricant
5.2.4 Detergent / Lubricant For cleaning MagSpring stators and slider, the cleaning spray LU06 is recommended. LinMot grease LU02 is prescribed to improve the sliding properties between the chrome-nickel steel surface of the slider and the plastic plain bearing. Ordering information... -
Page 23: Dimensions
1320 g (2.7 lb) MS01-40x325 0250-1008 305 mm [+1/-0.2] (12.0 in) 40 mm (1.46 in) 1750 g (3.6 lb) MS01-40x400 0250-1009 380 mm [+1/-0.2] (14.9 in) 40 mm (1.46 in) 2180 g (4.5 lb) NTI AG / LinMot MS01 Page 23 / 25... - Page 24 188 g (0.41 lb) ML01-12x375/160-20 0250-2326 375 mm (14.76 in) 12 mm (0.47 in) 188 g (0.41 lb) ML01-12x650/320-20 0250-2343 650 mm (25.59 in) 12 mm (0.47 in) 321 g (0.71 lb) Page 24 / 25 MS01 NTI AG / LinMot...
- Page 25 ALL LINEAR MOTION FROM A SINGLE SOURCE Headquarters Europe / Asia Headquarters North / South America NTI AG - LinMot & MagSpring LinMot USA Inc. Bodenaeckerstrasse 2 N1922 State Road 120, Unit 1 CH-8957 Spreitenbach Lake Geneva, WI 53147 Switzerland Sales / Administration: +41 56 419 91 91 Sales / Administration: 262.743.2555...