Table of Contents
Advertisement
chimney fire. Inspect the system at the stove connection and
at the chimney top. Cooler surfaces tend to build creosote
deposits quicker, so it is important to check the chimney
from the top as well as from the bottom. The creosote
should be removed with a brush specifically designed for
the type of chimney in use. A qualified chimney sweep can
perform this service. It is also recommended that before
each heating season the entire system be professionally
inspected, cleaned and, if necessary, repaired. To clean the
chimney, disconnect the vent from the stove.
FLY ASH
This accumulates in the horizontal portion of an exhaust
run. Though non-combustible, it may impede the normal
exhaust flow. It should therefore be periodically removed.
ASH REMOVAL & DISPOSAL
CAUTION:
ALLOW THE STOVE TO COOL BEFORE PERFORMING
ANY MAINTENANCE OR CLEANING. ASHES MUST
BE DISPOSED IN A METAL CONTAINER WITH A TIGHT
FITTING LID. THE CLOSED CONTAINER OF ASHES SHOULD
BE PLACED ON A NON-COMBUSTIBLE SURFACE OR ON
THE GROUND, WELL AWAY FROM ALL COMBUSTIBLE
MATERIALS, PENDING FINAL DISPOSAL.
Remove the ashes periodically to avoid unnecessary ash
build up. Remove ashes when unit has cooled. Ashes
should be placed in a metal container with a tight fitting
lid. The closed container of ashes should be placed on a
noncombustible floor or on the ground, well away from
all combustible materials, pending final disposal. If the
ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container
until all embers have been thoroughly cooled. The container
shall not be used for other trash or waste disposal. If
combined with combustible substances, ashes and embers
may ignite. Ash removal is as follows:
1. Let the fire burn out and allow the unit to cool to room
temperature.
2. Make sure the pellet stove is at room temperature before
touching. Clean the heat exchanger tubes.
3. Remove the burnpots inner section by grasping it and
pulling straight up.
4. Empty ashes from the inner section and scrape with
cleaning tool; make sure holes are not plugged.
5. Vacuum to remove ashes from the burn chamber interior
and the burnpot shell. WARNING: Make sure ashes are
cool to the touch before using a vacuum (see "Vacuum
Use").
© 2024 Breckwell
6. Dispose of ashes properly (see "Ash Removal").
7. Replace inner section into burnpot; make sure it is level
and pushed all the way back down and that the igniter
hole is to the rear when it is reinstalled.
8. Make sure the burnpot is level and pushed all the way
in. If the collar on the burnpot, attached to the fresh air
tube, is not pushed back to meet the firebox wall. The
igniter will not work properly.
SMOKE & CO MONITORS
Burning wood naturally produces smoke and carbon
monoxide(CO) emissions. CO is a poisonous gas when
exposed to elevated concentrations for extended periods
of time. While the modern combustion systems in heaters
drastically reduce the amount of CO emitted out the chimney,
exposure to the gases in closed or confined areas can be
dangerous. Make sure you stove gaskets and chimney joints
are in good working order and sealing properly to ensure
unintended exposure. It is recommended that you use both
smoke and CO monitors in areas having the potential to
generate CO.
CHECK & CLEAN THE HOPPER
Check the hopper periodically to determine if there is any
sawdust (fines) that is building up in the feed system or
pellets that are sticking to the hopper surface. Clean as
needed.
DOOR & GLASS GASKETS
Inspect the main door and glass window gaskets periodically.
The main door may need to be removed to have frayed,
broken, or compacted gaskets replaced by your authorized
dealer. This unit's door uses a 3/4" diameter rope gasket.
BLOWER MOTORS
Clean the air holes on the motors of both the exhaust and
distribution blowers annually. Remove the exhaust blower
from the exhaust duct and clean out the internal fan blades
as part of your fall start-up. If you have indoor pets your
power motors should be inspected monthly to make sure
they are free of animal hair build up. Animal hair build up
in blowers can result in poor performance or unforeseen
safety hazards.
PAINTED SURFACES
Painted surfaces may be wiped down with a damp cloth. If
scratches appear, or you wish to renew your paint, contact
your authorized dealer to obtain a can of suitable high-
temperature paint.
16
MAINTENANCE
Advertisement
Table of Contents
