Table of Contents
Advertisement
Quick Links
Maximal V Series
Dual Power Supply
Access Power Controllers (fused)
Models Include:
Maximal11V
- Power Supply 1:
12VDC @ 3.5A or 24VDC @ 2.7A.
- Power Supply 2:
12VDC @ 3.5A or 24VDC @ 2.7A.
- Sixteen (16) fuse protected outputs.
Maximal33V
- Power Supply 1:
12VDC @ 5.5A or 24VDC @ 5.7A.
- Power Supply 2:
12VDC @ 5.5A or 24VDC @ 5.7A.
- Sixteen (16) fuse protected outputs.
Installation Guide
Rev. DFV081011
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Maximal55V
- Power Supply 1: 12VDC @ 9.5A.
- Power Supply 2: 12VDC @ 9.5A.
- Sixteen (16) fuse protected outputs.
Maximal75V
- Power Supply 1: 12VDC @ 9.5A.
- Power Supply 2: 24VDC @ 9.7A.
- Sixteen (16) fuse protected outputs.
Maximal77V
- Power Supply 1: 24VDC @ 9.7A.
- Power Supply 2: 24VDC @ 9.7A.
- Sixteen (16) fuse protected outputs.
More than just power.
TM
Advertisement
Table of Contents
Related Manuals for Altronix Maximal V Series
Summary of Contents for Altronix Maximal V Series
- Page 1 Maximal V Series Dual Power Supply Access Power Controllers (fused) Models Include: Maximal11V Maximal55V - Power Supply 1: - Power Supply 1: 12VDC @ 9.5A. 12VDC @ 3.5A or 24VDC @ 2.7A. - Power Supply 2: 12VDC @ 9.5A. - Power Supply 2: - Sixteen (16) fuse protected outputs.
-
Page 2: Table Of Contents
Maximal V Series Configuration Chart ........ -
Page 3: Maximal V Series Overview
Maximal V Series Overview: Altronix Maximal V Access Power/Controllers distribute and switch power to access control systems and acces- sories. They convert a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into sixteen (16) independently controlled 12VDC or 24VDC fuse protected outputs. These Fail-Safe/Fail-Secure power outputs may be converted to dry form “C”... -
Page 4: Maximal V Installation Instructions
• Power supply input options: a) Factory installed power supplies provide common power for both ACM8 boards and all connected access control devices. b) An optional external access control power supply may be connected to isolate the ACM8 boards from the access control devices (only applicable on Maximal11V). - Page 5 (b) Fail-Secure Switched Power outputs: For Fail-Secure operation connect the positive (+) input of the access control devices to the terminal marked [NO]. Connect the negative (–) input of the access control devices to the terminal marked [COM]. (c) Form “C” outputs: When form “C”...
-
Page 6: Maintenance
Maintenance: Unit should be tested at least once a year for the proper operation as follows: FACP Supervision: To ensure proper connection and operation of the Fire Alarm disconnect hookup. Please follow the appropriate procedure below: Normally Open Input: Placing a short between terminals marked [T] and [+ INP] will trigger the Fire Alarm Disconnect. -
Page 7: Power Supply Board Terminal Identification
Power Supply Board Terminal Identification: Terminal Legend Function/Description L, N Connect 220VAC, 50/60Hz to these terminals: L to hot, N to neutral. Maximal11V - 12VDC @ 3.5A or 24VDC @ 2.7A to ACM8 boards. Maximal33V - 12VDC @ 5.5A or 24VDC @ 5.7A to ACM8 boards. Maximal55V - 12VDC @ 9.5A to ACM8 boards. -
Page 8: Power Supply Board Stand-By Battery Specifications
Power Supply Board Stand-by Battery Specifications: Altronix 20 Min. of 24 Hr. of Power Supply Board Battery 4 Hr. of Backup Model Backup Backup 12VDC/ 3.5A 0.5A AL400XB2V 40AH* (Refer to Fig. 1a, pg. 9 Maximal11 for Switch [SW1] 24VDC/ location and position) 2.7A... -
Page 9: Power Supply Board Output Voltage Settings
Power Supply Board Output Voltage Settings: Fig. 1a - Maximal11V and Maximal33V Power Supply Board Fig. 1b OFF - 24V ON - 12V OFF - 24V ON - 12V Access Power Controller Typical Application Diagram (for each ACM8): Fig. 2 Fig. -
Page 10: Maximal11V, Maximal33V, Maximal55V
Fig. 3 - Maximal11V, Maximal33V, Maximal55V Tamper Switch Power Supply Board BAT FAIL NC C NO NC C NO AC FAIL Line Neutral Ground Power Supply Board BAT FAIL NC C NO NC C NO AC FAIL Line Neutral Input 220VAC 50/60Hz CAUTION: When power supply board is set for 12VDC use only one (1) 12VDC stand-by battery. -
Page 11: Maximal75V Battery Hookup And Tamper Switch Installation
Fig. 4 - Maximal75V Tamper Switch Power Supply Board BAT FAIL NC C NO NC C NO AC FAIL Line Neutral Ground Power Supply Board BAT FAIL NC C NO NC C NO AC FAIL Line Neutral Input 220VAC 50/60Hz Optional 12VDC Optional 12VDC Rechargeable... -
Page 12: Maximal77V Battery Hookup And Tamper Switch Installation
Fig. 5 - Maximal77V Tamper Switch Power Supply Board BAT FAIL NC C NO NC C NO AC FAIL Line Neutral Ground Power Supply Board BAT FAIL NC C NO NC C NO AC FAIL Line Neutral Input 220VAC 50/60Hz Optional 12VDC Optional 12VDC Rechargeable... -
Page 13: Nec Power-Limited Wiring Requirements For Maximal11V
NEC Power-Limited Wiring Requirements for Maximal11V: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. -
Page 14: Nec Power-Limited Wiring Requirements For Maximal33V And Maximal55V
NEC Power-Limited Wiring Requirements for Maximal33V and Maximal55V: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. -
Page 15: Nec Power-Limited Wiring Requirements For Maximal75V
NEC Power-Limited Wiring Requirements for Maximal75V: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. -
Page 16: Nec Power-Limited Wiring Requirements For Maximal77V
NEC Power-Limited Wiring Requirements for Maximal77V: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. -
Page 17: Facp/Optional Power Supply Hook-Up Diagrams
FACP Hook-Up Diagrams: Fig. 10 Optional hook-up using two (2) isolated Fig. 11 Polarity reversal input from FACP power supply inputs signaling circuit output (polarity is (Only applicable on Maximal11V): referenced in alarm condition): CUT JUMPERS JUMPER J1 AND J2 FACP FACP OUTPUT EOL... - Page 18 - 18 - Maximal11V / Maximal33V / Maximal55V / Maximal75V / Maximal77V Access Power Controllers (Fused) Installation Guide...
- Page 19 Notes: Maximal11V / Maximal33V / Maximal55V / Maximal75V / Maximal77V Access Power Controllers (Fused) Installation Guide - 19 -...
-
Page 20: Enclosure Dimensions
(21.6mm) 4” (101.6mm) 2” (50.8mm) 19” (482.6mm) Altronix is not responsible for any typographical errors. –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIMaximal11V/33V/55V/75V/77V Series...
Need help?
Do you have a question about the Maximal V Series and is the answer not in the manual?
Questions and answers