CDVI DIGIWAY PLUS Manual page 16

DIGIWAY PLUS
Fully automated operator for inward or outward opening doors
Advanced Setting Ex Close Torque
12) 12)
Ex Close Torque
|||||||||||||||||...................
This function allows to set the TORQUE of the CLOSING extra pulse. Change the value by pressing the This function allows to set the TORQUE of the CLOSING extra pulse. Change the value by pressing the
UP or DOWN buttons and confirm with OK. UP or DOWN buttons and confirm with OK.
Default value = 50%. Default value = 50%.
Advanced Setting Extra Close Time
13) 13)
|||||||||||||||||.........0 SEC.
Extra Close Time
This function allows you to set the duration TIME of the CLOSING extra pulse. Change the value by This function allows you to set the duration TIME of the CLOSING extra pulse. Change the value by
pressing the UP or DOWN buttons and confirm with OK. pressing the UP or DOWN buttons and confirm with OK.
Default value Default value = 0 sec. = 0 sec.
Fonctions Avanc
14) 14) Relache incendie
Relache incendie
Ouvert/Libre/Fermé
When the Fire Release function is enabled, it's possible to set the reaction of the door depending on the When the Fire Release function is enabled, it's possible to set the reaction of the door depending on the
failure of the Fire Power (V+, V-): failure of the Fire Power (V+, V-):
• • DOOR FREE = In case of Fire Power failure the door becomes FREE (System Off) DOOR FREE = In case of Fire Power failure the door becomes FREE (System Off)
• • DOOR OPEN = In case of Fire Power failure the door opens and stays OPEN until the Fire Power is DOOR OPEN = In case of Fire Power failure the door opens and stays OPEN until the Fire Power is
reset or the function of the Menu Configuration is disabled. reset or the function of the Menu Configuration is disabled.
• • DOOR CLOSED LOCKED = Door CLOSED and lock active DOOR CLOSED LOCKED = Door CLOSED and lock active
• • DOOR CLOSED UNLOCKED = Door CLOSED and lock disactive DOOR CLOSED UNLOCKED = Door CLOSED and lock disactive
Advanced Setting Max Cycles Obst
15) 15)
Max Obst Cycles |||||||||||||||||.............000
When the door meets an obstacle during closing, it re-opens immediately. At the end of the pause time, When the door meets an obstacle during closing, it re-opens immediately. At the end of the pause time,
it re-closes. If the obstacle is still present the cycle restarts. This parameter sets the max number of re- it re-closes. If the obstacle is still present the cycle restarts. This parameter sets the max number of re-
closing attempts before the door stops and waits for an external command. closing attempts before the door stops and waits for an external command.
Range : from 1 to 256 . Value 0 of the parameter means no limit. Range : from 1 to 256 . Value 0 of the parameter means no limit.
Default value = 100 tentatives. Default value = 100 tentatives.
NOTE: At the end of the attempts the door remains stopped, until a different mode i set as NOTE: At the end of the attempts the door remains stopped, until a different mode i set as
described in the parameters Restart Time-out and Restart O/C Retry. described in the parameters Restart Time-out and Restart O/C Retry.
Advanced Setting OD on Closing
16) 16)
OD on Closing
Reopen
After the detection of an obstacle during closing the door will react in a different way, according to the After the detection of an obstacle during closing the door will react in a different way, according to the
following settings: following settings:
• • Reopen: Reopen: The door reopens and, after the pause time, recloses The door reopens and, after the pause time, recloses
• • Stop & Wait: Stop & Wait: The door stops and, after the pause time, recloses The door stops and, after the pause time, recloses
• • STOP: STOP: The door stops and waits for a command to reopen and for a further command to reclose. The door stops and waits for a command to reopen and for a further command to reclose.
Advanced Setting Approach speed
17) 17)
Approach speed
|||||||||||||||||......................
It is possible to change the approach speed as the door approaches the final close point. This is useful if It is possible to change the approach speed as the door approaches the final close point. This is useful if
the door senses an obstacle or finishes short of a strike. The door will accelerate a small amount when the door senses an obstacle or finishes short of a strike. The door will accelerate a small amount when
increased. increased.
Default value Default value = = 5. 5.
30
50 %
5
EN EN
Fully automated operator for inward or outward opening doors
Advanced Setting
18) 18)
Obst. detection %
It is possible to change the percentage at which the door does not detect an obstacle during the full door It is possible to change the percentage at which the door does not detect an obstacle during the full door
cycle allowing the door to close. cycle allowing the door to close.
100% = fully open, 0% = fully close 100% = fully open, 0% = fully close
Advanced Setting
19) 19)
Min Open Speed
It is possible to change the approach speed during the OPENING. This can be useful if the door meets It is possible to change the approach speed during the OPENING. This can be useful if the door meets
some friction in the approaching motion where it is searching for the open position. some friction in the approaching motion where it is searching for the open position.
Default value Default value = = 5. 5.
Advanced Setting
20) 20)
% Min Open Speed
It is possible to change the percentage of the It is possible to change the percentage of the
complete open trip after which the speed remains complete open trip after which the speed remains
at the value set with the parameter "Min Open at the value set with the parameter "Min Open
Speed". Speed".
Default value = = 2% Default value 2%
Advanced Setting
22) 22)
Test FTC
It is possible to disable the test on the re-open It is possible to disable the test on the re-open
photocell FTC: photocell FTC:
ATTENTION!! If the test is DISABLED the ATTENTION!! If the test is DISABLED the
operator must work in Low Energy Mode operator must work in Low Energy Mode
otherwise it doesn't operate in compliance otherwise it doesn't operate in compliance
with the EN16005 with the EN16005 Standard Standard. .
Advanced Setting
24) 24)
Test FTC Fail
In case the FTC safety photocells malfunction, you In case the FTC safety photocells malfunction, you
can set the operating mode to either: can set the operating mode to either:
STOP / LOW ENERGY STOP / LOW ENERGY
26) 26) Advanced Setting
Low Energy
The software calculates the minimum opening/ The software calculates the minimum opening/
closing time when the malfunction mode is set to closing time when the malfunction mode is set to
Low Energy, according to the doorset diameter (in Low Energy, according to the doorset diameter (in
metres) and weight (in kilograms). metres) and weight (in kilograms).
Advanced Setting
28) 28)
Latch ctrl pos
Sets the point in % that follows the Latch control Sets the point in % that follows the Latch control
torque setting. Useful for releasing over strikes. torque setting. Useful for releasing over strikes.
0% door closed - 100% door open 0% door closed - 100% door open
DIGIWAY PLUS
Obst. detection %
2%
|||||||||||||||||......................
Min Open Speed
5
|||||||||||||||||......................
% Min Open Speed
21) 21) Advanced Setting
.2%
|||||||||||||||||.................. O.D. Cycle
It is possible to set the type of cycle after an It is possible to set the type of cycle after an
obstacle detection: obstacle detection:
FAST: FAST: the door keeps normal speed after the the door keeps normal speed after the
detection of an obstacle. detection of an obstacle.
SLOW: SLOW: the speed of the door after an obstacle is the speed of the door after an obstacle is
reduced. reduced.
ENABLED / Advanced Setting
23) 23)
DISABLED Test FTC-S
It is possible to disable the test on the stop It is possible to disable the test on the stop
photocell FTC-S: photocell FTC-S:
ATTENTION!!: If the test is DISABLED the ATTENTION!!: If the test is DISABLED the
operator must work in Low Energy Mode operator must work in Low Energy Mode
otherwise it doesn't operate in compliance otherwise it doesn't operate in compliance
with the EN16005 Standard with the EN16005
STOP /
Advanced Setting
25) 25) ² ²
LOW ENERGY Test FTC-S Fail
In case the FTC-S safety photocells malfunction, In case the FTC-S safety photocells malfunction,
you can set the operating mode to either: you can set the operating mode to either:
STOP / LOW ENERGY STOP / LOW ENERGY
Diameter (m)
Advanced Setting
27) 27)
1,2 Low Energy
|||||||||||||||||......................
Sets the doorset weight in kilograms. Sets the doorset weight in kilograms.
Latch ctrl pos
Advanced Setting
29) 29)
3%
Latch ctrl torque
|||....................................
Boost the starting torque of the OPENING: Boost the starting torque of the OPENING:
setting of the torque value. setting of the torque value.
Default value = 0 Default value = 0
O.D. Cycle
Fast
ENABLED /
DISABLED
Standard. .
STOP /
LOW ENERGY
Weight ( Kg )
120
|||||||||||||||||...................
Latch ctrl torque
|||||||||||||||||...............5
31