Part V: Advanced Settings - CDVI DIGIWAY PLUS Manual

DIGIWAY PLUS
Fully automated operator for inward or outward opening doors

PART V: ADVANCED SETTINGS

DIGIWAY Plus is equipped with many additional parameters (all adjustable) to better suit any
type of installation. From the main menu select ADVANCED SET to enter this submenu, which
allows more adjustments.
Advanced Setting
Electrolock Time
1) 1)
Electrolock Time ||||||||||||||||......0,5 SEC.
It is possible to set the electrolock release time from 0.1 to 40 sec. depending on the lock/door type. It is possible to set the electrolock release time from 0.1 to 40 sec. depending on the lock/door type.
Press the UP or DOWN buttons to increase or decrease the pause time and confirm with OK. Press the UP or DOWN buttons to increase or decrease the pause time and confirm with OK.
Default value = 0.5 sec Default value = 0.5 sec
Advanced Setting
Opening Jolt Time
2) 2)
Opening Jolt Time ||||||||||||||||......0,5 SEC.
The opening jolt, when enabled, is a short closing motion before the operator begins opening - this The opening jolt, when enabled, is a short closing motion before the operator begins opening - this
relieves the pressure of "side-load" for some locking devices. You can adjust this time from 0.1 to 40 sec. relieves the pressure of "side-load" for some locking devices. You can adjust this time from 0.1 to 40 sec.
depending on the type of electrolock and door. Press the UP or DOWN buttons to increase or decrease depending on the type of electrolock and door. Press the UP or DOWN buttons to increase or decrease
the time and confirm with OK. the time and confirm with OK.
Default value = 0.5 sec. Default value = 0.5 sec.
Advanced Setting
Open Jolt Torque
3) 3)
Open Jolt Torque |||||||||||||||||...........20%
It is possible to adjust the torque of the motor during the opening jolt pulse. This is adjusted depending It is possible to adjust the torque of the motor during the opening jolt pulse. This is adjusted depending
on the mechanical resistance of the door. Press the UP or DOWN buttons to increase or decrease the on the mechanical resistance of the door. Press the UP or DOWN buttons to increase or decrease the
value and confirm with OK. value and confirm with OK.
Default value = 20%. Default value = 20%.
Advanced Setting Open Delay Time
4) 4)
Open Delay |||||||||||||||||.....0,5 SEC.
It is possible to add a short delay to the door motion to allow the electrolock bolt to fully exit from its It is possible to add a short delay to the door motion to allow the electrolock bolt to fully exit from its
keeper, ensuring the door is fully unlocked. This can be useful when using motorised locks. The open keeper, ensuring the door is fully unlocked. This can be useful when using motorised locks. The open
delay is set by pressing UP or DOWN buttons to increase or decrease from 0.1 to 40 sec and confirm delay is set by pressing UP or DOWN buttons to increase or decrease from 0.1 to 40 sec and confirm
with OK. with OK.
Default value Default value = 0.5 sec. = 0.5 sec.
Lock Lock
Motor Motor
Start Start
Advanced Setting Wind Stop Torque
5) 5)
Wind Stop Torque |||||||||||||||||............10%
It is possible to adjust the torque of the motor when the wind stop function is enabled. This allows you It is possible to adjust the torque of the motor when the wind stop function is enabled. This allows you
to change the value of the force applied by the door relative to the wind pressure. Press the UP or to change the value of the force applied by the door relative to the wind pressure. Press the UP or
DOWN buttons to increase or decrease the torque and confirm with OK. DOWN buttons to increase or decrease the torque and confirm with OK.
Default value Default value = 50%. = 50%.
28
Delay Delay
EN EN
Fully automated operator for inward or outward opening doors
Advanced Setting
Enable / Disable
6) 6)
Dynamic Pause
Dynamic pause is a function which automatically adjusts the programmed pause time, preventing too Dynamic pause is a function which automatically adjusts the programmed pause time, preventing too
many close attempts of the door in high traffic situations. When enabled, this function increases the many close attempts of the door in high traffic situations. When enabled, this function increases the
programmed pause time by 1 sec. each time it detects a passage through the door during the closing programmed pause time by 1 sec. each time it detects a passage through the door during the closing
phase, and restarts the time when passage is detected when the door is open. phase, and restarts the time when passage is detected when the door is open.
Once the door completes its cycle up to the closed status, the pause time is reset to the programmed Once the door completes its cycle up to the closed status, the pause time is reset to the programmed
value. value.
Press UP or DOWN buttons to enable or disable the function and confirm with OK. Press UP or DOWN buttons to enable or disable the function and confirm with OK.
Default value = DISABLE. Default value = DISABLE.
Advanced Setting
FTC-S Exclusion
7) 7)
FTC-S Exclusion
|||||||||||||||||.................
FTC-S active FTC-S active zone
Door Door
Wall Wall
WARNING: the excluded zone may become a health & safety hazard because it not protected! WARNING: the excluded zone may become a health & safety hazard because it not protected!
Advanced Setting
8) 8) Enable / Disable
Ex Power Open
When enabled, this adds one more OPENING pulse at the end of the opening cycle to compensate for When enabled, this adds one more OPENING pulse at the end of the opening cycle to compensate for
possible friction or door imbalance. Enable or disable this function with the UP or DOWN buttons and possible friction or door imbalance. Enable or disable this function with the UP or DOWN buttons and
confirm with OK. confirm with OK.
Default value = DISABLE. Default value = DISABLE.
Advanced Setting
9) 9) Ex Open Torque
Ex Open Torque
|||||||||||||||||..................
This function allows you to set the TORQUE of the OPENING extra pulse. This function allows you to set the TORQUE of the OPENING extra pulse.
Change the value by pressing the UP or DOWN buttons and confirm with OK. Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value Default value = 50%. = 50%.
Advanced Setting Extra Open Time
10) 10)
Extra Open Time
|||||||||||||||||...............
This function allows to set the duration TIME of the OPENING extra pulse. This function allows to set the duration TIME of the OPENING extra pulse.
Change the value by pressing the UP or DOWN buttons and confirm with OK. Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value Default value = 0 sec. = 0 sec.
Advanced Setting
11) 11)
Ex Power Close
When enabled, this adds one more CLOSING pulse after the regular CLOSING cycle to compensate for When enabled, this adds one more CLOSING pulse after the regular CLOSING cycle to compensate for
possible friction or door imbalance. Enable or disable this function with the UP or DOWN buttons and possible friction or door imbalance. Enable or disable this function with the UP or DOWN buttons and
confirm with OK. confirm with OK.
Default value = DISABLE. . Default value = DISABLE
DIGIWAY PLUS
000
If the door is next to a wall and is using a curtain protection device, it If the door is next to a wall and is using a curtain protection device, it
may be necessary to prevent the device being activated by the wall to may be necessary to prevent the device being activated by the wall to
allow a complete opening of the leaf. allow a complete opening of the leaf.
zone
Set the zone width as a percentage of the full door motion using the Set the zone width as a percentage of the full door motion using the
UP or DOWN buttons to increase or decrease the value. UP or DOWN buttons to increase or decrease the value.
000 = Door OPEN 000 = Door OPEN
100 = Door CLOSED 100 = Door CLOSED
Example: if you want to disable the curtain device when the leaf is Example: if you want to disable the curtain device when the leaf is
open at 80% of the complete travel, set the value to 20. open at 80% of the complete travel, set the value to 20.
50 %
0 SEC.
Enable / Disable
29