Language Selection; Master Transmitter Memorisation; Wizard Setup - CDVI DIGIWAY PLUS Manual

DIGIWAY PLUS
Fully automated operator for inward or outward opening doors

LANGUAGE SELECTION

Press and hold the OK button on the keyboard until the Press and hold the OK button on the keyboard until the
1
display enters the main menu. display enters the main menu.
Select the language by scrolling through the list using the UP Select the language by scrolling through the list using the UP
2
and Down buttons. and Down buttons.
Press OK to confirm: the display shows the message "OK" and Press OK to confirm: the display shows the message "OK" and
3
then displays all messages in the new language. then displays all messages in the new language.
4
Exit the menu with the ESC button. Exit the menu with the ESC button.

MASTER TRANSMITTER MEMORISATION

Scroll through the main menu, select TX MANAGEMENT Scroll through the main menu, select TX MANAGEMENT
5
submenu and press OK. submenu and press OK.
6
Select the option ADD TX MASTER and press OK Select the option ADD TX MASTER and press OK
Press the OK key on the transmitter (top-left button): Press the OK key on the transmitter (top-left button):
7
the display will show the serial number, confirming the the display will show the serial number, confirming the
memorisation. memorisation.
8 Exit the menu with the ESC button. Exit the menu with the ESC button.
9 Exit the main menu selecting EXIT MENU. Exit the main menu selecting EXIT MENU.
NOTES: NOTES:
The system accepts only ONE Master Transmitter. Any other transmitters must be memorised The system accepts only ONE Master Transmitter. Any other transmitters must be memorised
as "regular" and will only serve to trigger the door operation. as "regular" and will only serve to trigger the door operation.
In case of loss of the Master Transmitter it is possible to replace it with an identical 4-button In case of loss of the Master Transmitter it is possible to replace it with an identical 4-button
Transmitter. Transmitter.
A Master transmitter cannot be memorised as a Regular transmitter. A Master transmitter cannot be memorised as a Regular transmitter.
A Regular transmitter cannot be memorised as a Master transmitter. A Regular transmitter cannot be memorised as a Master transmitter.
Important: Important: do not issue this transmitter to the end user as programming or factory defaults do not issue this transmitter to the end user as programming or factory defaults
could be applied unintentionally. could be applied unintentionally.
20
EN
Up Up
ESC ESC
Down Down
Up Up
ESC ESC
Down Down
EN
Fully automated operator for inward or outward opening doors
The setup of the operator can be divided into The setup of the operator can be divided into 4 steps
• • PART PART I I : CONFIGURATION (setup of the basic operating mode) : CONFIGURATION (setup of the basic operating mode)
• • PART II PART II : DOOR CALIBRATION (automatic detection of the door characteristics) : DOOR CALIBRATION (automatic detection of the door characteristics)
• • PART PART III : ADJUSTMENTS (further adjustments and personalisation) III : ADJUSTMENTS (further adjustments and personalisation)
• • PART PART IV : SPECIAL PARAMETERS (setup of the advanced parameters) IV : SPECIAL PARAMETERS (setup of the advanced parameters)

WIZARD SETUP

In the Main menu select the Wizard setup to initiate a basic setup of the operator. The guided
menu will ask you to specify the main parameters for basic operation of the unit and will
complete the adjustment with the calibration of the door.
At the end of the procedure the door will operate in a basic manner.
To complete the setup and tailor the settings to the installation site of the automated door, go
to the remaining parameters in the Configuration, Main, and Advanced Settings submenus.
Main Menu
Main Menu Lock Type is
Setup Wizard Magnet
Electrolock time
.........................0,5S
NOTE: NOTE: the command the command
ESC will abort the ESC will abort the
Pause time
..........................10S
procedure procedure
Push Button Mode
OPEN/CLOSE
Spring mode
ENABLE
Arm type is
SLIDING
SWITCH DOOR TO
FREE MODE
Follow the steps
requested for the
door calibration
Disable Test FTC/S
Y/N
SETUP COMPLETED Disable test FTC
SET SWITCH to I Y/N
DIGIWAY PLUS
4 steps: :
Set the lock: no-lock, Magnet or
Strike
Set the lock release time
Set the pause time
Follow the indications to proceed with Follow the indications to proceed with
the calibration the calibration
Disable the tests on the safety inputs Disable the tests on the safety inputs
(5-6-7) if they are shorted. (5-6-7) if they are shorted.
21