Table of Contents
Advertisement
WARNING!
•
Do not leave the key fob in or near the vehicle (or
in a location accessible to children), and do not
leave the ignition in the ACC or ON/RUN position. A
child could operate power windows, other controls,
or move the vehicle.
CAUTION!
Damage to the transmission may occur if the follow-
ing precautions are not observed:
•
Shift into or out of PARK or REVERSE only after the
vehicle has come to a complete stop.
•
Do not shift between PARK, REVERSE, NEUTRAL,
or DRIVE when the engine is above idle speed.
•
Before shifting into any gear, make sure your foot
is firmly pressing the brake pedal.
To Turn On The Engine Using ENGINE START/STOP
Button
1. The transmission must be in PARK or NEUTRAL.
2. Press and hold the brake pedal while pushing the
ENGINE START/STOP button once.
To release the parking brake manually, the ignition
switch must be in the ON/RUN position. Press on the
brake pedal, then push the parking brake switch
momentarily.
If the driver shifts into PARK while moving, the vehicle
may Park.
PARK will engage ONLY when vehicle speed is 1.2 mph
(1.9 km/h) or less.
The message "Vehicle Speed Is Too High To Shift To P"
will display in the instrument cluster display if vehicle
speed is above 1.2 mph (1.9 km/h).
The gear position indicator will blink continuously until
the gear selector is returned to the proper position, or
the requested shift can be completed.
WARNING!
If vehicle speed is not below 1.2 mph (1.9 km/h)
when the driver shifts into PARK, the transmission will
default to NEUTRAL until the vehicle speed drops
below 1.2 mph (1.9 km/h) and the conditions are
met, enabling AutoPark. A vehicle left in the NEUTRAL
position can roll. As an added precaution, always
apply the parking brake when exiting the vehicle.
EXTENDED PARK STARTING
NOTE:
Extended Park condition occurs when the vehicle has
not been started or driven for at least 30 days.
1. Install a battery charger or jumper cables to the bat-
tery to ensure a full battery charge during the crank
cycle.
2. Place the ignition to the START position and release
it when the engine starts. For Keyless Enter 'n Go™
ignition systems, press and hold the brake pedal
while pushing the ENGINE START/STOP button once.
3. If the engine fails to start within 10 seconds, wait
10 to 15 seconds to allow the starter to cool, then
repeat the Extended Park Starting procedure.
4. If the engine fails to start after eight attempts, allow
the starter to cool for at least 10 minutes, then
repeat the Extended Park Starting procedure.
STARTING AND OPERATING
CAUTION!
To prevent damage to the starter, do not crank con-
tinuously for more than 10 seconds at a time. Wait
10 to 15 seconds before trying again.
IF ENGINE FAILS TO START
If the engine fails to start after you have followed the
"Normal Starting" procedure and the vehicle has not
experienced an Extended Park condition as previously
defined, it may be flooded. Push the accelerator pedal
all the way to the floor and hold it there while the
engine is cranking. This should clear any excess fuel in
case the engine is flooded.
The starter motor will engage automatically, run for
10 seconds, and then disengage. Once this occurs,
release the accelerator pedal and the brake pedal, wait
10 to 15 seconds, then repeat the "Normal Starting"
procedure
WARNING!
•
Never pour fuel or other flammable liquid into the
throttle body air inlet opening in an attempt to
start the vehicle. This could result in flash fire
causing serious personal injury.
•
Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic
transmission cannot be started this way. Unburned
fuel could enter the catalytic converter and once
the engine has started, ignite and damage the con-
verter and vehicle.
121
4
(Continued)
Advertisement
Table of Contents
