Page 1 CHRYSLER PACIFICA HYBRID 2019 USER GUIDE...
Page 2 The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. FCA US LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road.
Page 3: How To Find Your Owner's Manual Online
Congratulations on selecting your new FCA US This User Guide has been prepared to help you For more detailed descriptions of the topics dis- LLC vehicle. Be assured that it represents precision quickly become acquainted with the important fea- cussed in this User Guide, as well as information workmanship, distinctive styling, and high quality.
Page 4: How To Use This Manual How To Use This Manual
HOW TO USE THIS To identify the chapter with the information needed WARNINGS AND you can consult the index at the end of this User MANUAL CAUTIONS Guide. Essential Information While reading this User Guide you will find a series Chapters can be rapidly identified with dedicated of WARNINGS to be followed to prevent incorrect graphic tabs, at the side of each odd page.
Page 5: Graphical Table Of Contents
GRAPHICAL TABLE OF CONTENTS GETTING TO KNOW YOUR VEHICLE GETTING TO KNOW YOUR INSTRUMENT PANEL SAFETY STARTING AND OPERATING IN CASE OF EMERGENCY SERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS MULTIMEDIA CUSTOMER ASSISTANCE INDEX...
Page 6: Table Of Contents
WELCOME FROM FCA US LLC DOORS ......27 Rear Wiper And Washer ....49 Keyless Enter-N-Go —...
Page 7 INTERNAL EQUIPMENT ....71 Supplemental Restraint Systems (SRS) ..105 PARKSENSE REAR PARK ASSIST — Power Outlets ..... 71 IF EQUIPPED .
Page 8 FUSES ......168 Wheel And Wheel Trim Care ... . 209 Pairing The Remote .
Page 9: Instrument Panel
INSTRUMENT PANEL Instrument Panel 1 — Multifunction Lever 7 — Glove Compartment 12 — Gear Selector 2 — Instrument Cluster Display Controls 8 — Climate Controls 13 — Ignition 3 — Instrument Cluster 9 — Switch Panel 14 — Speed Controls 4 —...
Page 10: Interior
INTERIOR Interior Features 1 — Power Window/Door Lock Switches 3 — Seats 2 — Door Handles...
Page 11: High Voltage Battery
HIGH VOLTAGE High Voltage Battery Service Disconnect NOTE: BATTERY • During vehicle start up and shut down a clicking The High Voltage Battery Service Disconnect is noise may be heard from within the vehicle. When located under the access panel, in front of the sec- Your vehicle is equipped with a Lithium-ion high the ignition is in the ON position, the high voltage ond row passenger seating.
Page 12: High Voltage Charging Operation
• Under cold or hot temperatures, while the vehicle is plugged-in and the ignition is in the OFF posi- tion, the vehicle may wake-up to pre-condition the high voltage battery for usage. • It is recommended that the vehicle be plugged-in over night where possible to maximize the electric range of the vehicle.
Page 13 To access the portable charging cord set, open the WARNING! WARNING! door of the cargo area storage bin, on the driver’s • Do not use Portable EVSE Cordset with an uids to pour or drip on the EVSE. If water side, and remove the charging cord set from the extension cord.
Page 14 2. Check to see if the charging cordset is ready to 3. If the charging cordset is ready to charge, ensure charge by reviewing the indicator lights. After a the vehicle is in PARK, and then connect the brief self-check, where the indicator light will charge connector to the vehicle’s charge inlet.
Page 15: Ac Level 2 Charging (240V, 30 Amp Or 32 Amp)
uled time and day of the week. If a charging AC Level 2 Charging (240V, 30 Amp for this charging event by plugging in the charge schedule has been enabled in the vehicle, and connector, unplugging it, and then plugging it Or 32 Amp) it is outside the time and day of the week, you back into the vehicle charge inlet.
Page 16: Vehicle Charge Indicators
NOTE: Vehicle Charge Indicators Instrument Panel State Of Charge Indicator • The charging times below are estimates based on Instrument Cluster High Voltage Battery Dis- In addition to the battery display, your vehicle is charging a high voltage battery that has a <1% play equipped with a visual state of charge indicator.
Page 17: Hybrid Electric Pages
NOTE: Hybrid Electric Pages Number Of Indicator Percent Of Battery The lights scroll one at a time when the vehicle is Lights Illuminated Charge Within your Uconnect 4C/4C NAV system is the plugged in outside of its charging schedule time/ Lights turn on one at a Indicates system is wait- “Hybrid Electric Pages”...
Page 18 Power Flow When one day of the week exceeds 100 miles (160 km) driven, the values of miles (km) driven in The first screen within the “Hybrid Electric Pages” Electric and Hybrid modes will be listed above the App is the Power Flow screen. The Power Flow bar graph in respective colors (teal for Electric and screen shows the current power readings for all of blue for Hybrid).
Page 19: Keys
end time, allowing the vehicle to continue to charge NOTE: The charging schedule can also be overridden if the for an amount of time after the start time until the If the vehicle is plugged in outside of the charging EVSE is plugged in, unplugged, and then plugged vehicle is fully charged, as long as the vehicle is schedule set in the Uconnect 4C radio, the vehicle’s...
Page 20 NOTE: In case the ignition switch does not change with the The key fob may not be found if it is located next to push of a button, the key fob may have a low or fully a mobile phone, laptop or other electronic device; depleted battery.
Page 21 To Unlock The Doors NOTE: Uconnect Settings lets you program the system to unlock either the driver's side doors on the first push (default) or unlock all doors on the first push of the unlock button on the key fob. To change the default setting, refer to “Uconnect Settings”...
Page 22 To Lock The Doors And Liftgate Request For Additional Remote Controls Push and release the lock button on the key fob to NOTE: lock all doors and liftgate. The hazard lights will Only key fobs that are programmed to the vehicle flash once and the horn will chirp once to acknowl- electronics can be used to start and operate the edge the signal.
Page 23 KeySense Features — If Equipped Start Up Display Features General Information • Unique splash screen graphic This feature provides the vehicle owner with the The following regulatory statement applies to all ability to customize vehicle settings that can be radio frequency (RF) devices equipped in this ve- •...
Page 24: Ignition Switch
IGNITION SWITCH The Keyless Push Button Ignition has four operat- ing positions; three of which are labeled and will This feature allows the driver to start the vehicle illuminate when in position. The three positions are with the push of a button, as long as the key fob is in OFF, ACC, and ON/RUN.
Page 25 • Engine Temporarily Operating in “Fuel and Oil WARNING! Maintenance Mode” • Some electrical devices are available. • When leaving the vehicle, always remove the • Hood Opened with Ignition in Run Post-Start • Mechanical power (Vehicle Propulsion) is not key fob from the vehicle and lock your Mode (eliminate unexpected engine start-ups) available.
Page 26: Remote Starting System - If Equipped
REMOTE STARTING How To Use Remote Start CAUTION! SYSTEM — IF EQUIPPED All of the following conditions must be met before An unlocked vehicle is an invitation. Always re- the vehicle will remote start: move the key from the ignition and lock all the NOTE: •...
Page 27: To Enter Remote Start Mode
NOTE: NOTE: WARNING! Changes or modifications not expressly approved • The vehicle can be started two consecutive times by the party responsible for compliance could void • Do not start or run an engine in a closed (two 15-minute cycles) from the key fob. However, the user’s authority to operate the equipment.
Page 28: To Disarm The System
• For vehicles equipped with Keyless Enter- • Grasp the Passive Entry Unlock Door Handle (if • When the vehicle security alarm is armed, the N-Go — Passive Entry, make sure the vehicle equipped, refer to "Keyless Enter-N-Go — Pas- interior power door lock switches will not unlock ignition system is OFF.
Page 29: Doors
DOORS • The key fob may not be able to be detected by the vehicle passive entry system if it is located next to Keyless Enter-N-Go — Passive Entry a mobile phone, laptop, wireless charging pad, or other electronic device; these devices may block The Passive Entry system is an enhancement to the the key fob’s wireless signal and prevent the pas- vehicle’s Remote Keyless Entry system and a fea-...
Page 30 To Unlock From The Passenger Side: • A lock request is made by the door panel switch To Enter The Liftgate while the door is open. With a valid key fob within 5 ft (1.5 m) of the With a valid key fob within 5 ft (1.5 m) of the liftgate, When any of these situations occur, after all open passenger door handle, grab the front passenger cycle the handle to open the liftgate and pull the...
Page 31 The vehicle doors can also be locked by using the key fob lock button, or the lock button located on the vehicle’s interior door panel. General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this ve- hicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS stan-...
Page 32: Power Sliding Side Door - If Equipped
Power Sliding Side Door — If Equipped The power sliding door may be power opened or closed in several ways: • Key fob • Inside or outside handles • Buttons located: – In the overhead console – Just inside the sliding door –...
Page 33: Hands-Free Sliding Doors - If Equipped
handles are manual. When the LED is lit, pushing Hands-Free Sliding Doors — the power sliding door power off button will return If Equipped the handles to power operation. NOTE: • If anything obstructs the power sliding side door while it is closing or opening, the door will auto- matically reverse to the closed or open position and an audible tone will sound, provided it meets sufficient resistance.
Page 34: Child Locks
When a valid kicking motion is completed, the slid- • If the power sliding doors encounters multiple ob- structions within the same cycle, the system will ing door will chime, the hazard lights will flash and automatically stop. the sliding door will open almost instantaneously. This assumes all options are enabled in the radio The Hands-Free Sliding Doors feature may be settings.
Page 35: Seats
• To avoid unintentional operation of the power NOTE: Manual Adjustment (Rear Seats) sliding door from the rear seats, push the Slid- • After disengaging (or engaging) the Child Pro- ing Door Power Off button, located in the over- WARNING! tection Door Lock, always test the inside door head console.
Page 36 Easy Entry Slide Second Row Seating 4. To put the seat back into original position, just pull back on the seatback and lock the seat into The second row seats can be tilted and slid forward position. for easy entry into the third row. 1.
Page 37: Driver Memory Seat - If Equipped
Reinstalling Seat To Unfold Third Row Seats Driver Memory Seat — If Equipped 1. To reinstall the seat, align the seat’s front attach- 1. Pull up on the assist strap to lift the seat out of the The Memory Buttons (1) and (2) on the driver's ments into the detent positions on the floor.
Page 38 Programming The Memory Feature Linking And Unlinking The Remote Keyless 5. Push and release the lock button on the key fob within 10 seconds. Entry Key Fob To Memory To create a new memory profile, perform the fol- lowing: Your key fob can be programmed to recall one of NOTE: two pre-programmed memory profiles by pushing Your key fob can be unlinked to your memory set-...
Page 39: Heated Seats
A recall can be cancelled by pushing any of the • When the ignition is cycled to the OFF position, You can choose from HI, LO, or OFF heat settings. the driver seat will move to a position 0.3 inches The indicator lights in each switch indicate the level memory buttons on the driver's door during a recall (7.7 mm) forward of the rear stop if the driver seat...
Page 40: Ventilated Seats - If Equipped
Vehicles Equipped With Remote Start Ventilated Seats — If Equipped This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in On models that are equipped with remote start, the Located in the first row seat cushions are small fans “Multimedia”...
Page 41: Head Restraints
HEAD RESTRAINTS Head Restraints — Front Seats The front driver and passenger seats are equipped Head restraints are designed to reduce the risk of with four-way head restraints. injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.
Page 42: Head Restraints - Second Row
NOTE: Head Restraints — Second Row NOTE: To remove the head restraint, raise it as far as it can To remove the head restraint, raise it as far as it can The second row outboard head restraints are ad- go. Then, push the release button and the adjust- go then push the release button and the adjustment justable.
Page 43: Head Restraints - Third Row
Head Restraints — Third Row The head restraint in the center position can be raised and lowered for tether routing or height ad- The outboard head restraints can be manually justment. Refer to “Occupant Restraint Systems” in folded forward for improved rearward visibility. Pull “Safety”...
Page 44: Steering Wheel
STEERING WHEEL ward as desired. To lengthen or shorten the steering The heated steering wheel control button is located column, pull the steering wheel outward or push it within the Uconnect system. You can gain access to Tilt/Telescoping Steering Column inward as desired.
Page 45: Mirrors
Resetting The Power Folding Outside Mirrors WARNING! You may need to reset the power folding mirrors if must exercise care when using the steering the following occurs: wheel heater. It may cause burns even at low • The mirrors are accidentally blocked while folding. temperatures, especially if used for long peri- ods.
Page 46: Exterior Lights
EXTERIOR LIGHTS Headlight Switch Rotate the headlight switch clockwise to the second detent for parking light and instrument panel light The headlight switch is located on the left side of Multifunction Lever operation. Rotate the headlight switch to the third the instrument panel.
Page 47: Automatic High Beam - If Equipped
Automatic High Beam — If Equipped 3. Push the multifunction lever away from you to Flash-To-Pass switch the headlights to the high beam position. The Automatic High Beam system provides in- You can signal another vehicle with your headlights Refer to “Multifunction Lever” for further creased forward lighting at night by automating by lightly pulling the multifunction lever toward you.
Page 48: Headlights On With Wipers - If Equipped
Headlights On With Wipers — When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60, or 90 sec- If Equipped onds or not remain on. To change the timer setting, When your headlights are in the AUTO mode and select the proper setting through the Uconnect the vehicle is running, the headlights will automati- System.
Page 49: Windshield Wiper And Washers
NOTE: WARNING! If either light remains on and does not flash, or there vehicles or other obstacles. To avoid sudden ic- is a very fast flash rate, check for a defective outside ing of the windshield during freezing weather, light bulb. If an indicator fails to light when the lever warm the windshield with the defroster before is moved, it would suggest that the indicator bulb is and during windshield washer use.
Page 50: Rain Sensing Wipers - If Equipped
tent interval previously selected. If the lever is pulled the operator desires more wiping sensitivity, they unless the wiper control on the multifunction lever is moved, the vehicle speed becomes greater than while the wipers are in the off position, the wipers may select sensitivity position 4.
Page 51: Rear Wiper And Washer
Rear Wiper And Washer Automatic Climate Controls Rear Windshield Wiper Operation The front controls are located on the touchscreen (if equipped) and on the instrument panel below Rotate the windshield wiper lever center ring up- the radio. The rear climate controls are located on wards to operate one of two modes for the rear the touchscreen and in the rear headliner, on the window wiper:...
Page 52 Automatic Climate Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. NOTE: The MAX A/C setting is only available on the touchscreen.
Page 53 Icon Description Rear Defrost Button Push and release the Rear Defrost Control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ten minutes. Rear Climate Control Button Rear Climate Press and release this button to access the rear climate controls.
Page 54 Icon Description Modes Control Knob Modes Control Faceplate: Push the button in the center of the knob to change the airflow distribution mode. Touchscreen: Select Mode by pressing one of the Mode Buttons on the touchscreen. MODE The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.
Page 55: Automatic Temperature Control (Atc) - If Equipped
Climate Control Functions MAX A/C Automatic Temperature Control (ATC) — If Equipped A/C (Air Conditioning) MAX A/C sets the control for maximum cooling performance. Automatic Operation The Air Conditioning (A/C) button allows the op- erator to manually activate or deactivate the air Press and release to toggle between MAX A/C and 1.
Page 56 To provide you with maximum comfort in the auto- Controlling The Rear Climate Controls From • To return to the front screen on the Uconnect system, press the "Front Climate" on the matic mode, during cold start-ups, the blower fan The Front ATC Touchscreen touchscreen.
Page 57 Icon Description Rear Passenger Temperature Up And Down Buttons Provides the rear passengers with independent temperature control. Push the up arrow button on the touchscreen to increase the tem- perature. Push the down arrow button on the touchscreen to decrease the temperature. When the SYNC feature is active, the passenger’s temperature moves up and down with the driver’s temperature.
Page 58 Icon Description Bi-Level Mode Bi-Level Mode Press this button on the touchscreen to change the air distribution mode to Bi-Level Mode. In Bi-Level Mode, air comes from the instru- ment panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 59 Icon Description Rear Mode Control Push this button on the Rear Climate Hard Controls to change the air distribution mode for the rear passengers to one of the following: Panel Mode Panel Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow.
Page 60: Operating Tips
Icon Description Rear Blower Control The rear blower control can be manually set to off, or any fixed blower speed by pushing the blower control buttons. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle. The larger of the two icons increases blower speed, whereas the smaller of the two icons decreases the blower speed.
Page 61: Windows
Window Fogging Outside Air Intake The controls will operate only when the ignition switch is in the ON/RUN or ACC position and Vehicle windows tend to fog on the inside in mild, Make sure the air intake, located directly in front of during power accessory delay.
Page 62 NOTE: NOTE: NOTE: The controls will not operate if the driver has acti- Power Window controls will also remain active for • If the window runs into any obstacle during auto- vated the Power Window Lockout. up to 10 minutes after the ignition switch has been closure, it will reverse direction and then go back turned to OFF, depending upon the accessory de- down.
Page 63: Panoramic Sunroof - If Equipped
Wind Buffeting PANORAMIC SUNROOF The Power Shade switch is located to the right between the sun visors on the overhead console. — IF EQUIPPED Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in WARNING! the ears.
Page 64: Opening Sunroof
Opening Sunroof NOTE: Power Sun Shade — If Equipped If the sunshade is in the closed position when the Express Mode The sunshade has two programmed open positions: vent switch is pushed, the sunshade will automati- half-open and full-open. When opening the sun- Push the switch rearward and release it within one cally cycle to the halfway open position prior to the shade from the closed position, the sunshade will...
Page 65: Pinch Protect Feature
cally to the full-open position. Any release of the Pinch Protect Feature HOOD switch will stop the movement and the sunshade will This feature will detect an obstruction in the closing Opening remain in a partially opened condition until the of the sunroof during the Express Close operation.
Page 66: Closing
• If the vehicle was actively charging the HV battery when the hood was opened, the vehicle will stop charging until the hood is closed. Closing 1. Hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab.
Page 67: Liftgate
the outside handle will unlock and release the lift- Closing CAUTION! gate, with a valid Passive Entry key fob within 5 ft To Close The Liftgate (1.5 m) of the liftgate. To prevent possible damage, do not slam the Grasp the liftgate closing handle and initiate lower- hood to close it.
Page 68: Power Liftgate - If Equipped
Power Liftgate — If Equipped Hands-Free Liftgate foot activation (if equipped) will unlock and open the liftgate, with a valid Passive The power liftgate may be opened or closed in Entry key fob within 5 ft (1.5 m) of the liftgate several ways: handle.
Page 69: Hands-Free Liftgate - If Equipped
Lock The Vehicle To open the liftgate using hands-free activation, use NOTE: a straight in and out kicking motion under the ve- • The Hands-Free Liftgate will only operate when With a valid Passive Entry key fob within 5 ft (1.5 m) hicle activation zone in the general location below the transmission is in Park.
Page 70: Universal Garage Door Opener (Homelink)
• The HomeLink buttons that are located in the WARNING! WARNING! overhead console or sunvisor designate the three travel path is clear. Make sure the liftgate is different HomeLink channels. • Driving with the liftgate open can allow poi- closed and latched before driving away. sonous exhaust gases into your vehicle.
Page 71: Erasing All The Homelink Channels
If you have any problems, or require assistance, Rolling Code Devices Programming HomeLink To A Garage please call toll-free 1-800-355-3515 or, on the Inter- Door Opener To determine if your device has a rolling code, a net at HomeLink.com for information or assistance. good indicator is its manufacturing date.
Page 72: Programming Homelink To A Miscellaneous Device
NOTE: Non-Rolling Code Garage Door Opener Final Programming HomeLink To A Make sure the garage door opener motor is Steps Miscellaneous Device plugged in before moving on to the rolling code/ 1. Push and hold the programmed HomeLink but- Refer to “Programming HomeLink To A Garage non-rolling code final steps.
Page 73: Reprogramming A Single Homelink Button
Reprogramming A Single HomeLink General Information INTERNAL EQUIPMENT Button The following regulatory statement applies to all Power Outlets To reprogram a single HomeLink button that has Radio Frequency (RF) devices equipped in this ve- Your vehicle is equipped with 12 Volt (15 Amp) been previously trained, without erasing all the hicle: power outlets, that can be used to power cellular...
Page 74 CAUTION! CAUTION! Power outlets are designed for accessory plugs • Many accessories that can be plugged in draw only. Do not insert any other object in the power power from the vehicle's battery, even when outlets as this will damage the outlet and blow not in use (i.e., cellular phones, etc.).
Page 75: Power Inverter - If Equipped
Power Inverter — If Equipped The Power Inverter turns on when the device is plugged in, and the ignition is in RUN mode. It turns There is a 115 Volt, 150 Watt Power Inverter outlet off when the device is unplugged or the ignition is located on the right side of the vehicle, before the no longer in RUN mode.
Page 76: Instrument Cluster Display
INSTRUMENT CLUSTER Instrument Cluster Display Location The system allows the driver to select information by pushing the following buttons mounted on the And Controls DISPLAY steering wheel: The Instrument Cluster Display is located in the Your vehicle is equipped with an instrument cluster center of the instrument cluster.
Page 77: Oil Life Reset
• Right Arrow Button • Unless reset, this message will continue to display Secondary Method For Oil Life Reset Procedure each time the ignition is cycled to the ON/RUN Push and release the right arrow button to access 1. Without pushing the brake pedal, place the igni- position.
Page 78: Instrument Cluster Display Menu Items
With KeySense in use there will be multiple associated messages shown in the following table: Setting Instrument Cluster Display Message None – With vehicle ignition ON “KeySense in use. Max vehicle speed set to xx MPH/or km/h” • “Max speed reached. KeySense in use” supported by a chime Max Vehicle Speed •...
Page 79: Warning Lights And Messages
WARNING LIGHTS AND until the fault is cleared. If the light is either not on If the light remains on when the parking brake has during startup, stays on, or turns on while driving, been disengaged, and the fluid level is at the full MESSAGES have the system inspected at an authorized dealer mark on the master cylinder reservoir, it indicates a...
Page 80 If brake failure is indicated, immediate repair is The light also will turn on when the parking brake is If the light turns on while driving, safely pull over necessary. applied with the ignition switch in the ON/RUN and stop the vehicle. If the A/C system is on, turn it position.
Page 81 If the light continues to flash when the vehicle is — Oil Temperature Warning Light or slightly faster, with the transmission in PARK or running, immediate service is required and you may NEUTRAL, until the light turns off. Once the light This warning light will illuminate to indicate the experience reduced performance, an elevated/ turns off, you may continue to drive normally.
Page 82 — Hood Open Warning Light — Hybrid Electric Vehicle System Ser- • “Issue Detected Check External Charging Sta- tion” – If you see this message, the charging sta- vice Light This warning light will illuminate when the hood is tion maybe powered off, having internal fault or This warning light will illuminate when service to the left open and not fully closed.
Page 83: Yellow Warning Lights
Yellow Warning Lights vated. It should go out with the engine running. If — Electronic Park Brake Warning Light the “ESC Indicator Light” comes on continuously This warning light will illuminate to indicate the — Anti-Lock Brake (ABS) Warning with the engine running, a malfunction has been Electronic Park Brake is not functioning properly Light detected in the ESC system.
Page 84 — Low Washer Fluid Warning Light — If — Engine Check/Malfunction Indica- WARNING! Equipped tor Warning Light (MIL) mable substances such as dry plants, wood, card- This warning light will illuminate when the wind- The Engine Check/Malfunction Indicator Light board, etc. This could result in death or serious shield washer fluid is low.
Page 85 Should one or more tires be in the condition men- tires as soon as possible, and inflate them to the ways check the TPMS malfunction telltale after tioned above, the display will show the indications proper pressure. Driving on a significantly under- replacing one or more tires or wheels on your ve- corresponding to each tire.
Page 86: Yellow Indicator Lights
Yellow Indicator Lights — KeySense Indicator Light — — Adaptive Cruise Control (ACC) Set If Equipped With No Target Detected Light — — Forward Collision Warning Off Indica- If Equipped The KeySense indicator is illuminated when a Key- tor Light — If Equipped Sense key is detected upon startup of the vehicle.
Page 87: White Indicator Lights
— Park/Headlight On Indicator Light • “Plugged in and Charging Complete” — Cruise Control ON Indicator Light This indicator light will illuminate when the park This indicator light will illuminate when the elec- NOTE: tronic speed control is ON, but a speed has not lights or headlights are turned on.
Page 88: Onboard Diagnostic System - Obd
ONBOARD DIAGNOSTIC CAUTION! WARNING! SYSTEM — OBD II • Prolonged driving with the MIL on could • ONLY an authorized service technician Your vehicle is equipped with a sophisticated On- cause further damage to the emission control should connect equipment to the OBD II con- board Diagnostic system called OBD II.
Page 89: Safety Features
SAFETY FEATURES AUXILIARY DRIVING SYSTEMS Regenerative Braking System (RBS) — Hybrid Blind Spot Monitoring Your vehicle has a Regenerative Braking System The Blind Spot Monitoring (BSM) system uses two (RBS). The RBS replenishes the vehicle's high volt- radar-based sensors located inside the rear bumper age battery during deceleration, and is particularly fascia to detect highway licensable vehicles (auto- useful in stop-and-go city traffic.
Page 90 exposed. The RCP system will then have a clear WARNING! view of the cross traffic and if an oncoming vehicle is driver detect an oncoming vehicle in a parking detected, alert the driver. lot situation. Drivers must be careful when back- RCP monitors the rear detection zones on both ing up, even when using RCP.
Page 91: Forward Collision Warning (Fcw)
Blind Spot Alert Lights/Chime NOTE: NOTE: Changes or modifications not expressly approved • The BSM system will store the current operating When operating in Blind Spot Alert Lights/Chime by the party responsible for compliance could void mode when the vehicle is shut off. Each time the mode, the BSM system will provide a visual alert in the user’s authority to operate the equipment.
Page 92 • To turn the FCW system back on, press the for- More cautious drivers that do not mind frequent mous braking, or additional brake support if the ward collision button again to turn the system on. warnings may prefer this setting. driver is not braking adequately in the event of a potential frontal collision.
Page 93: Tire Pressure Monitor System (Tpms)
1. This device may not cause harmful interference. The tire pressure will vary with temperature by ap- nates, you must increase the tire pressure to the proximately 1 psi (7 kPa) for every 12°F (6.5°C). recommended cold placard pressure in order for 2.
Page 94 NOTE: • Seasonal temperature changes will affect tire pres- CAUTION! sure, and the TPMS will monitor the actual tire When filling warm tires, the tire pressure may need • After inspecting or adjusting the tire pressure pressure in the tire. to be increased up to an additional 4 psi (28 kPa) always reinstall the valve stem cap.
Page 95 Tire Pressure Monitoring Low Pressure Should this occur, you should stop as soon as pos- no longer flash, and the “SERVICE TPM SYSTEM” sible and inflate the tires with low pressure (those in message will no longer display, and a pressure value Warnings a different color in the instrument cluster display will display in place of the dashes.
Page 96 and a chime will sound. In addition, the graphic in active road tires. The vehicle may need to be dashes (--) will remain in place of the pressure the instrument cluster will still display a different driven for up to 20 minutes above 15 mph values.
Page 97: Occupant Restraint Systems
(2) This device must accept any interference re- Important Safety Precautions 5. You should read the instructions provided with ceived, including interference that may cause unde- your child restraint to make sure that you are Please pay close attention to the information in this sired operation.
Page 98: Seat Belt Systems
Enhanced Seat Belt Use Reminder System BeltAlert Warning Sequence WARNING! (BeltAlert) The BeltAlert warning sequence is activated when • Never install a rear-facing child restraint in the the vehicle is moving above a specified vehicle Driver and Passenger BeltAlert (if equipped) front seat of a vehicle.
Page 99 The outboard front passenger seat BeltAlert is not you under normal conditions. However, in a collision WARNING! active when the outboard front passenger seat is the seat belt will lock and reduce your risk of striking • Be sure everyone in your vehicle is in a seat unoccupied.
Page 100 the latch plate and pull out the seat belt. Slide the WARNING! WARNING! latch plate up the webbing as far as necessary to as strong as shoulder bones. Wear the seat belt won’t be at the strong hip and pelvic bones, allow the seat belt to go around your lap.
Page 101 4. Position the lap belt so that it is snug and lies low 2. At about 6 to 12 inches (15 to 30 cm) above the across your hips, below your abdomen. To re- latch plate, grasp and twist the seat belt webbing move slack in the lap belt portion, pull up on the 180 degrees to create a fold that begins imme- shoulder belt.
Page 102 NOTE: Second Row Center (If Equipped) And Third The adjustable upper shoulder belt anchorage is Row Center Seat Belt Operating Instructions equipped with an Easy Up feature. This feature The second row center (if equipped) and third row allows the shoulder belt anchorage to be adjusted in center seat belts feature a seat belt with a mini-latch the upward position without pushing or squeezing plate and buckle, which allows the seat belt to de-...
Page 103 9. To release the seat belt, push the red button on the buckle. 10. To disengage the mini-latch plate from the mini-buckle for storage, insert the regular latch plate into the center red slot on the mini-buckle. The seat belt will automatically retract to its stowed position.
Page 104 Seat Belt Extender Position the lap belt snug and low below the abdo- WARNING! men and across the strong bones of the hips. Place If a seat belt is not long enough to fit properly, even Remove and store the Seat Belt Extender the shoulder belt across the chest and away from when the webbing is fully extended and the adjust- when not needed.
Page 105 Energy Management Feature Allow the webbing to retract completely in this case and then carefully pull out only the amount of web- The front outboard seat belt system is equipped bing necessary to comfortably wrap around the oc- with an Energy Management feature that may help cupant’s mid-section.
Page 106 How To Engage The Automatic Locking Mode WARNING! 1. Buckle the combination lap and shoulder belt. • Do not use the Automatic Locking Mode to 2. Grasp the shoulder portion and pull downward restrain occupants who are wearing the seat until the entire seat belt is extracted.
Page 107: Supplemental Restraint Systems (Srs)
Supplemental Restraint Systems • Supplemental Knee Air Bags (SRS) • Front and Side Impact Sensors Some of the safety features described in this section • Seat Belt Pretensioners may be standard equipment on some models, or • Seat Track Position Sensors may be optional equipment on others.
Page 108 tarily or continuously. A single chime will sound to For additional information regarding the Redun- WARNING! alert you if the light comes on again after initial dant Air Bag Warning Light refer to “Getting To startup. Know Your Instrument Panel” section of this Ignoring the Air Bag Warning Light in your in- manual.
Page 109 The first stage inflator is triggered immediately dur- WARNING! ing an impact that requires air bag deployment. A • Never place a rear-facing child restraint in low energy output is used in less severe collisions. A front of an air bag. A deploying passenger higher energy output is used for more severe colli- front air bag can cause death or serious injury sions.
Page 110 On the other hand, depending on the type and Occupant Classification System (OCS) — WARNING! location of impact, front air bags may deploy in Front Passenger Seat harm if the vehicle is in a collision severe crashes with little vehicle front-end damage but that The OCS is part of a Federally regulated safety produce a severe initial deceleration.
Page 111 Bag deployment based on occupant classification. Front Passenger Seat Front Passenger Air WARNING! In order for the OCS to operate as designed, it is Occupant Status Bag Output • Children 12 years or younger should always important for the front passenger to be seated Properly seated adult Full-power deployment ride buckled up in the rear seat of a vehicle...
Page 112 • Sitting with their back against the seatback and the of the occupant that it detects. The OCS will detect • Objects are lodged between the front passenger seatback in an upright position seat and center console. the front passenger’s decreased or increased seated weight, which may result in an adjusted inflation rate •...
Page 113 WARNING! • Do not carry or hold any objects (e.g., back- packs, boxes, etc.) while seated in the front passenger seat. Holding an object may pro- vide an output signal to the OCS that is dif- ferent than the occupant’s properly seated weight input, which may result in serious injury or death in a collision.
Page 114 The passenger seat assembly contains critical OCS • Do not add a secondary seat cover or mat. Knee Impact Bolsters components that may affect the Passenger Ad- • At no time should any Supplemental Restraint The Knee Impact Bolsters help protect the knees of vanced Front Air Bag inflation.
Page 115 Supplemental Side Air Bags WARNING! Supplemental Seat-Mounted Side Air Bags Do not use accessory seat covers or place ob- (SABs) jects between you and the Side Air Bags; the This vehicle is equipped with Supplemental Seat- performance could be adversely affected and/or Mounted Side Air Bags (SABs).
Page 116 properly, or if items are positioned in the area where Side Impacts the SABICs inflate. Children are at an even greater The Side Air Bags are designed to activate in cer- risk of injury from a deploying air bag. tain side impacts. The Occupant Restraint Control- The SABICs may help reduce the risk of partial or ler (ORC) determines whether the deployment of complete ejection of vehicle occupants through...
Page 117 ployment is appropriate. In the event the vehicle WARNING! WARNING! experiences a rollover or near rollover event, and • Being too close to the Side Air Bags during deployment of the Side Air Bags is appropriate, the • Occupants, including children, who are up deployment could cause you to be severely rollover sensing system will also deploy the seat belt against or very close to Side Air Bags can be...
Page 118 • Supplemental Knee Air Bags • As the air bags deflate, you may see some smoke- • After any collision, the vehicle should be taken to like particles. The particles are a normal by- an authorized dealer immediately. • Front and Side Impact Sensors product of the process that generates the non- Enhanced Accident Response System •...
Page 119 • Cut off battery power to the: Enhanced Accident Response System Reset WARNING! – Engine Procedure trim cover or the upper passenger side of the – Electric Motor (if equipped) After an event occurs requiring activation of the instrument panel. Do not modify the front –...
Page 120: Child Restraints
Event Data Recorder (EDR) NOTE: Children 12 years or younger should ride properly EDR data are recorded by your vehicle only if a buckled up in a rear seat, if available. According to This vehicle is equipped with an event data recorder non-trivial crash situation occurs;...
Page 121 Before buying any restraint system, make sure that it NOTE: • Canadian residents should refer to Transport Canada’s website for additional information: has a label certifying that it meets all applicable • For additional information, refer to http:// http://www.tc.gc.ca/eng/motorvehiclesafety/ Safety Standards. You should also make sure that www.nhtsa.gov/parents-and-caregivers or call: safedrivers-childsafety-index-53.htm you can install it in the vehicle where you will use it.
Page 122 Infant And Child Restraints WARNING! WARNING! Safety experts recommend that children ride rear- Do not install a rear-facing car seat using a rear • Never place a rear-facing child restraint in facing in the vehicle until they are two years old or support leg in this vehicle.
Page 123 Older Children And Child Restraints 2. Do the child’s knees bend comfortably over the WARNING! front of the vehicle seat – while the child is still Children who are two years old or who have outgrown directions exactly when installing an infant or sitting all the way back? their rear-facing convertible child seat can ride child restraint.
Page 124 Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Use Any Attachment Method Shown With An “X” Below Child + Child Restraint LATCH – Lower Seat Belt Only LATCH – Lower Anchors Seat Belt + Top Anchors Only + Top Tether Anchor Tether Anchor Rear-Facing Child Restraint...
Page 125 Frequently Asked Questions Use the LATCH anchorage system until the combined weight What is the weight limit (child’s weight + weight of the child of the child and the child restraint is 65 lbs (29.5 kg). Use the restraint) for using the LATCH anchorage system to attach the 65 lbs (29.5 kg) seat belt and tether anchor instead of the LATCH system once child restraint?
Page 126 NOTE: Locating The LATCH Anchorages If the folding, non-adjustable head restraint inter- The lower anchorages are round bars that are feres with the installation of the child restraint, the found at the rear of the seat cushion where it meets head restraint may be folded and the child seat the seatback, below the anchorage symbols on the installed in front of it.
Page 127 Locating The Upper Tether Anchorages There are tether strap anchorages located behind all second row seating positions. The third row has a tether anchor on the 40% seat for the right outboard position and in the center of the 60% seat for either the center or left outboard seating posi- tion.
Page 128 Center Seat LATCH If a child restraint installed in the center position To Install A LATCH-Compatible Child Re- blocks the seat belt webbing or buckle for the out- straint This vehicle has 4 lower LATCH anchorages in the board position, do not use that outboard position. If If the selected seating position has a Switchable third row, rear seat.
Page 129 3. Attach the lower hooks or connectors of the How To Stow An Unused Switchable-ALR WARNING! child restraint to the lower anchorages in the (ALR) Seat Belt: selected seating position. • Improper installation of a child restraint to the When using the LATCH attaching system to install 4.
Page 130 Installing Child Restraints Using The Vehicle The seat belts in the passenger seating positions are Lap/Shoulder Belt Systems For Installing equipped with a Switchable Automatic Locking Re- Child Restraints In This Vehicle Seat Belt tractor (ALR) that is designed to keep the lap por- Child restraint systems are designed to be secured tion of the seat belt tight around the child restraint in vehicle seats by lap belts or the lap belt portion of...
Page 131 Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight of the child Always use the tether anchor when using the seat belt to install restraint) for using the Tether Anchor with the seat belt to Weight limit of the Child Restraint a forward facing child restraint, up to the recommended weight attach a forward facing child restraint?
Page 132 NOTE: WARNING! If the folding, non-adjustable head restraint inter- feres with the installation of the child restraint, the • Improper installation or failure to properly se- head restraint may be folded and the child seat cure a child restraint can lead to failure of the installed in front of it.
Page 133 3. Slide the latch plate into the buckle until you hear 8. If the child restraint has a top tether strap and the Seat Belt Park Stitch — If Equipped a “click.” seating position has a top tether anchorage, con- The rear outboard seat belts may be equipped with nect the tether strap to the anchorage and 4.
Page 134 If the park stitch interferes with the lock-off features Installing Child Restraints Using the Top 1. Look behind the seating position where you plan of the child restraint, do not use the lock-off feature. Tether Anchorage to install the child restraint to find the tether Instead, switch the seat belt to the locking mode, as anchorage.
Page 135 and where possible, route the tether strap under 2. If the car seat is in the center, raise the center WARNING! the head restraint and between the two posts. If head restraint and route the tether strap around not possible, lower the head restraint and pass the inboard (left) side of the head restraint sup- •...
Page 136: Transporting Pets
Transporting Pets WARNING! Air Bags deploying in the front seat could harm your • Do not allow people to ride in any area of your pet. An unrestrained pet will be thrown about and vehicle that is not equipped with seats and possibly injured, or injure a passenger during panic seat belts.
Page 137: Safety Checks You Should Make Inside The Vehicle
Safety Checks You Should Make detected. It will stay on until the fault is removed. If WARNING! the light comes on intermittently or remains on Inside The Vehicle • If it is necessary to sit in a parked vehicle with while driving, have an authorized dealer service the the engine running, adjust your heating or vehicle immediately.
Page 138 WARNING! WARNING! WARNING! • ONLY use the driver’s side floor mat on the • If the vehicle carpet has been removed and An improperly attached, damaged, folded, or driver’s side floor area. To check for interfer- re-installed, always properly attach carpet to stacked floor mat, or damaged floor mat fasten- ence, with the vehicle properly parked with the the floor and check the floor mat fasteners are...
Page 139: Periodic Safety Checks You Should Make Outside The Vehicle
Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges.
Page 140: Starting The Vehicle
STARTING THE VEHICLE Request Propulsion System Active (PSA) or “Ve- 3. The READY indicator will appear in the cluster hicle is Ready to Drive” mode with the gear selector when the vehicle is in ready to drive mode, which Before starting your vehicle, adjust your seat, adjust in the PARK position.
Page 141 NOTE: AutoPark ALWAYS DO A VISUAL CHECK that your ve- hicle is in PARK by looking for the “P” in the Instru- • The vehicle is not able to be driven in the AutoPark is a supplemental feature to assist in plac- ment Cluster Display and on the shifter.
Page 142 to the PARK position. The Electric Park Brake • Vehicle is not in PARK WARNING! SAFE HOLD feature will also activate in some • Vehicle speed is 1.2 MPH (1.9 km/h) or less cator solidly indicates PARK (P) without blink- conditions.
Page 143: After Starting
(1.9 km/h). The gear position indicator will blink WARNING! CAUTION! continuously until the selector is returned to the • When exiting the vehicle, always make sure • Before shifting into any gear, make sure your proper position, or the requested shift can be the ignition is in the OFF mode, remove the foot is firmly pressing the brake pedal with the completed.
Page 144: Engine Break-In Recommendations
3. If the gear selector is not in PARK, with vehicle opening and closing of any passenger compart- The engine oil installed in the engine at the factory ment door (requires all doors to be closed before is a high-quality energy conserving type lubricant. speed less than 5 mph (8 km/h), when the EN- the FOB check will occur).
Page 145: Park Brake
PARK BRAKE To release the park brake manually, the ignition • The park brake can be engaged even when the ignition switch is OFF. However, it can only be switch must be in the ON/RUN position. Press on Electric Park Brake (EPB) disengaged when the ignition switch is in the ON/ the brake pedal, then push the parking brake switch RUN position.
Page 146: Automatic Transmission
AUTOMATIC WARNING! CAUTION! TRANSMISSION ous for a number of reasons. A child or others If the Brake System Warning Light remains on could be seriously or fatally injured. Children with the parking brake released, a brake system WARNING! should be warned not to touch the parking malfunction is indicated.
Page 147: Hybrid Transmission
Hybrid Transmission WARNING! WARNING! The transmission is controlled using a rotary elec- • It is dangerous to shift out of PARK or NEU- could be seriously or fatally injured. Children tronic gear selector located on the center console. TRAL if your foot is not firmly pressing the should be warned not to touch the park brake, The transmission gear range (PRNDL) is displayed brake pedal.
Page 148: Speed Control
NOTE: NOTE: You must press the brake pedal to shift the transmis- In order to ensure proper operation, the Speed sion out of PARK (or NEUTRAL, when stopped or Control System has been designed to shut down if moving at low speeds). multiple Speed Control functions are operated at the same time.
Page 149: To Set A Desired Speed
To Resume Speed ADAPTIVE CRUISE WARNING! CONTROL (ACC ) — To resume a previously set speed, push the RES Leaving the Speed Control system on when not button and release. Resume can be used at any IF EQUIPPED in use is dangerous. You could accidentally set speed above 20 mph (32 km/h).
Page 150: To Activate/Deactivate
Adaptive Cruise Control (ACC) increases the driv- WARNING! WARNING! ing convenience provided by cruise control while • Will bring the vehicle to a complete stop driving involvement. It is always the driver’s traveling on highways and major roadways. How- while following a target vehicle and hold responsibility to be attentive of road, traffic, ever, it is not a safety system and not designed to the vehicle for approximately 3 minutes...
Page 151: To Set A Desired Acc Speed
To turn the system off, push and release the Adap- NOTE: • ACC cannot be resumed if there is a stationary vehicle in-front of your vehicle in close proximity. tive Cruise Control (ACC) on/off button again. At ACC cannot be set if there is a stationary vehicle in this time, the system will turn off and the instrument front of your vehicle in close proximity.
Page 152: Setting The Following Distance In Acc
U.S. Speed (mph) Panel” in the Owner’s Manual. The speed incre- • When you use the SET (-) button to decelerate, if ment shown is dependant on the speed of U.S. the powertrain braking power does not slow the • Pushing the SET (+) button once will result in a (mph) or Metric (km/h) units: vehicle sufficiently to reach the set speed, the 1 mph increase in set speed.
Page 153: General Information
To increase the distance setting, push the Distance PARKSENSE REAR PARK • The automatic braking function may not provide enough vehicle deceleration to avoid colliding Setting — Increase button and release. Each time ASSIST — IF EQUIPPED with a detected obstacle depending on vehicle the button is pushed, the distance setting increases speed, road conditions, and brake capability.
Page 154: Parksense Sensors
• The driver must stay in full control of the vehicle's ParkSense Sensors Enabling And Disabling ParkSense acceleration and braking and is responsible for the The four ParkSense sensors, located in the rear vehicle's movements. ParkSense can be enabled and disabled fascia/bumper, monitor the area behind the vehicle with the ParkSense switch, located on Refer to “ParkSense System Usage Precautions”...
Page 155: Parksense System Usage Precautions
NOTE: • Clean the ParkSense sensors regularly, taking care WARNING! not to scratch or damage them. The sensors must When KeySense feature is present, the ParkSense not be covered with ice, snow, slush, mud, dirt or backing up. You are responsible for safety and System will reject customer input to turn the system debris.
Page 156: Parksense Front And Rear Park Assist - If Equipped
NOTE: The automatic braking function is intended to assist CAUTION! the driver in avoiding possible collisions with de- • The driver can override the automatic braking cated above or below the sensors will not be tected obstacles when backing up in REVERSE function by pressing the gas pedal, turning detected when they are in close proximity.
Page 157: Parksense Sensors
speed, a warning will appear in the instrument clus- Enabling And Disabling ParkSense NOTE: ter display indicating the vehicle speed is too fast. When KeySense feature is present, the ParkSense The system will become active again if the vehicle System will reject customer input to turn the system ParkSense can be enabled and disabled speed is decreased to speeds less than approxi- off via the hard switch.
Page 158: Enabling And Disabling The Parksense Active Park Assist System
NOTE: Enabling And Disabling The LANESENSE — ParkSense Active Park Assist System • The driver is always responsible for controlling the IF EQUIPPED vehicle, responsible for any surrounding objects, LaneSense Operation and must intervene as required. The ParkSense Active Park Assist system can be enabled and disabled •...
Page 159: Turning Lanesense On Or Off
ter display to prompt the driver to remain within the NOTE: yellow (on/off), while the outside lane line on the left of the display will remain solid yellow. The lane. When only a single lane marking is detected, a The LaneSense system will retain the last system LaneSense telltale changes from solid white haptic (torque) warning will not be provided.
Page 160: Changing Lanesense Status
• When the LaneSense system senses the lane has • The system will not apply torque to the steering When the vehicle is shifted out of REVERSE (with been approached and is in a lane departure situa- wheel whenever a safety system engages. (anti- camera delay turned off), the rear camera mode is tion, the left inside lane line flashes yellow (on/off) lock brakes, traction control system, electronic sta-...
Page 161: Surround View Camera System - If Equipped
NOTE: NOTE: CAUTION! If snow, ice, mud, or any foreign substance builds up The Surround View Camera System has program- recommended that the driver look frequently on the camera lens, clean the lens, rinse with water, mable settings that may be selected through the over his/her shoulder when using ParkView.
Page 162 Different colored zones indicate the distance to the Rear View Deactivation rear of the vehicle. This is the Default view of the system in REVERSE The system can be deactivated in the following Modes Of Operation and is paired with a Top view of the vehicle with conditions: active guide lines for the projected path when en- •...
Page 163: Refueling The Vehicle
REFUELING THE 3. The button press will initiate a sequence of WARNING! events to depressurize the fuel system. A mes- VEHICLE sage will display in the cluster letting you know Drivers must be careful when backing up even 1. Put the vehicle in the PARK postion. when the vehicle is ready to be fueled.
Page 164 • The fuel door could take up to 15 seconds to NOTE: 2. Insert funnel into same filler pipe opening as the open. It may take longer to open in some fuel nozzle, ensure funnel is inserted fully to hold In certain cold conditions, ice may prevent the situations, such as high ambient tempera- both flapper doors open.
Page 165: Materials Added To Fuel
Emergency Fuel Door Release 4. After removing green handle from retention Materials Added To Fuel bracket, then pull the green handle directly away 1. Cycle the vehicle's ignition to the RUN position from the bracket to release the fuel door. Designated TOP TIER (PSA not active) Detergent Gasoline con-...
Page 166: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF The Ground All Models Flat Tow NONE NOT ALLOWED Front Dolly Tow Rear NOT ALLOWED On Trailer NOTE: Recreational Towing — All Models CAUTION! • To avoid inadvertent Electric Park Brake engage- DO NOT flat tow this vehicle.
Page 167 5. Turn the ignition OFF. 6. Properly secure the front wheels to the dolly, following the dolly manufacturer's instructions. 7. Turn the ignition to the ON/RUN mode, but do not start the vehicle. 8. Press and hold the brake pedal. 9.
Page 168: Hazard Warning Flashers
HAZARD WARNING flash on and off to warn oncoming traffic of an When you must leave the vehicle to seek assistance, the Hazard Warning flashers will continue to oper- emergency. Push the switch a second time to turn FLASHERS ate even though the ignition is placed in the OFF off the Hazard Warning flashers.
Page 169 Exterior Bulbs Lamps Bulb Number Projector Halogen Low Beam - 9005HL+ Halogen Headlamp High Beams - 9005LL Dedicated Daytime Running Lamp (If Equipped) LED (Serviced at Authorized Dealer) Front Turn Signal Lamp PWY24WNA Side Marker Lamp Front Park Lamp LED (Serviced At Authorized Dealer) Front Fog Lamp H11LL LED Front Fog Lamp...
Page 170: Fuses
FUSES Before any procedure is done on the PDC, make WARNING! sure engine is turned off. • If the replaced fuse blows again, contact an WARNING! Remove the cover by unlatching the two locks lo- authorized dealer. cated at each side of the PDC cover, avoid the •...
Page 171 Cavity Cartridge Fuse Blade Fuse Description – – Not Used F14A – Media Hub 1, 2, 3 10 Amp Red F14B – Pwr Lumbar Switch 40 Amp Green – CBC / Power Locks – 20 Amp Yellow – – Not Used 40 Amp Green –...
Page 172 Cavity Cartridge Fuse Blade Fuse Description 20 Amp Blue – 30 Amp Pink – Power Liftgate Module 25 Amp Clear – Rear Door Control Module - Lt 25 Amp Clear – Sunroof Control Module – – Not Used 40 Amp Green –...
Page 173 Cavity Cartridge Fuse Blade Fuse Description F55A – RF Hub/KIN/ESL - BUX Only 15 Amp Blue F55B – DVD / VRM F56A – FRT. & RR HVAC CTRL/ OCM / ESL 10 Amp Red F56B – B. EPS / ESC - Electric Stability Ctr –...
Page 174 Cavity Cartridge Fuse Blade Fuse Description – 5 Amp Tan Overhead Console / Rear ICS – 20 Amp Yellow Uconnect / DCSD / Telematics Rear Entertainment / Media HUB / 3RD & 2ND Row USB CHRG / F77A – Vacuum Cleaner SW Backlight / 3RD Row Recliner SW Backlight / 10 Amp Red 2ND Row Stow N Go SW Backlight / LT&RT Sliding Door Backlight F77B...
Page 175 Cavity Cartridge Fuse Blade Fuse Description F92A – 5 Amp Tan Security Gateway F92B – – Not Used – – Not Used 40 Amp Green – ESC - Motor Pump F95A – USB Charge Only Port 10 Amp Red F95B –...
Page 176: Jacking And Tire Changing
JACKING AND TIRE WARNING! CHANGING The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. NOTE: Your vehicle is not equipped with a jack or spare tire. Preparations For Jacking This section describes wheel removal and 1.
Page 177 1. Loosen (but do not remove) the wheel lug nuts WARNING! by turning them to the left one turn while the • Turn on the Hazard Warning flasher. wheel is still on the ground. • Block the wheel diagonally opposite the wheel 2.
Page 178 WARNING! WARNING! Being under a jacked-up vehicle is dangerous. Raising the vehicle higher than necessary can The vehicle could slip off the jack and fall on you. make the vehicle less stable. It could slip off the You could be crushed. Never get any part of jack and hurt someone near it.
Page 179: Road Tire Installation
Refer to “Torque Specifications” in “Technical Specifications” for proper wheel lug nut torque. If in doubt about the correct tightness, have them checked with a torque wrench by an autho- rized dealer or at a service station. 9. Lower the jack to its fully lowered position. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of...
Page 180 4. Install the remaining lug nuts with the cone pattern until each nut has been tightened twice. WARNING! shaped end of the nut toward the wheel. Lightly Refer to “Torque Specifications” in “Technical tighten all the lug nuts until the wheel sits flush Specifications”...
Page 181: Tire Service Kit - If Equipped
TIRE SERVICE KIT — Tire Service Kit Storage IF EQUIPPED The Tire Service Kit is secured with a strap and is stored in the storage bin located behind the rear cargo trim panel. Tire Service Kit And Components And Opera- tion Tire Service Kit (Bottom View) 1 —...
Page 182 Selecting Sealant Mode • When the Tire Service Kit sealant is in a liquid WARNING! form, clean water, and a damp cloth will remove Push in the Mode Select Knob and turn to this the material from the vehicle or tire and wheel •...
Page 183 2. Verify that the valve stem (on the wheel with the NOTE: WARNING! deflated tire) is in a position that is near to the Do not remove foreign objects (e.g., screws or nails) are serious or fatal to you, your passengers, ground.
Page 184 2. Connect the Power Plug to a different 12 Volt If the tire does not inflate to at least 26 psi Drive Vehicle: power outlet in your vehicle or another vehicle, if (1.8 Bar) pressure within 15 minutes: Immediately after injecting sealant and inflating the available.
Page 185 2. Place the Tire Service Kit flat on the ground next NOTE: Sealant Bottle Replacement: to the deflated tire. If the tire becomes over-inflated, push the De- 1. Unwrap the power cord. flation Button to reduce the tire pressure to the 3.
Page 186: Jump Starting
JUMP STARTING the vehicle's "jump posts" and then shifting the Jump starting can be dangerous if done improperly transmission from PARK into NEUTRAL. Power so please follow the procedures in this section care- The vehicle requires its 12V battery power to "turn- provided by the jumper cables will also allow the fully.
Page 187: Preparations For Jump Start
Preparations For Jump Start 3. If using another vehicle to jump start the 12V WARNING! electrical system, park the vehicle within the jumper cables reach, set the parking brake and You can be seriously injured or killed working on make sure the ignition is OFF. or around a motor vehicle: •...
Page 188: Refueling In Emergency
Connecting The Jumper Cables 5. Start the vehicle that has the booster battery, let If frequent jump starting is required to start your the vehicle run a few minutes, and then cycle the vehicle, you should have the battery and charging 1.
Page 189: If Your Engine Overheats
IF YOUR ENGINE NOTE: WARNING! Shifts between DRIVE and REVERSE can only be OVERHEATS hood, do not open the hood until the radiator achieved at wheel speeds of 5 mph (8 km/h) or less. has had time to cool. Never try to open a cooling Whenever the transmission remains in NEUTRAL In any of the following situations, you can reduce system pressure cap when the radiator or coolant...
Page 190: Towing A Disabled Vehicle
WARNING! CAUTION! CAUTION! (48 km/h) or for longer than 30 seconds continu- every five rocking-motion cycles. This will the wheels faster than 15 mph (24 km/h), or ously without stopping when you are stuck and minimize overheating and reduce the risk of drivetrain damage may result.
Page 191 Proper towing or lifting equipment is required to If flatbed equipment is not available, this vehicle • Use approved receptacle location to free the dis- abled vehicle from its environment. prevent damage to your vehicle. Use only tow bars must towed with the front wheels OFF the ground and other equipment designed for this purpose, (using a towing dolly, or wheel lift equipment with following equipment manufacturer’s instructions.
Page 192: Enhanced Accident Response System (Ears)
EVENT DATA RECORDER CAUTION! CAUTION! (EDR) • Be applied parallel to the center line of the • When securing the vehicle to a flatbed truck, length of the vehicle. do not attach to front or rear suspension com- This vehicle is equipped with an Event Data Re- •...
Page 193: Scheduled Servicing
SCHEDULED SERVICING message can be reset by referring to “Vehicle Info” • Check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed. in “Instrument Cluster Display” in “Getting To Know Your vehicle is equipped with an automatic oil Your Instrument Panel”...
Page 194 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Inspect front accessory drive belt, tensioner, idler pulley, and replace if necessary. Additional Maintenance Replace engine air cleaner filter.
Page 195: Heavy Duty Use Of The Vehicle
WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your ve- hicle to a competent mechanic.
Page 196: Engine Compartment - Hybrid
ENGINE COMPARTMENT — HYBRID 1 — Battery Coolant Reservoir* 5 — Remote Jump Start Positive Terminal 9 — Power Electronics Coolant Reservoir* 2 — Engine Coolant Reservoir 6 — Power Distribution Center (Fuses) 10 — Washer Fluid Reservoir 3 — Engine Oil Fill 7 —...
Page 197: Raising The Vehicle
RAISING THE VEHICLE Tire Markings • European — Metric tire sizing is based on Euro- pean design standards. Tires designed to this stan- In the case where it is necessary to raise the vehicle, dard have the tire size molded into the sidewall go to an authorized dealer or service station.
Page 198 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 199 EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or • C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load –...
Page 200 Tire Terminology And Definitions Term Definition The vehicle B-Pillar is the structural member of the body located behind the front door. B-Pillar Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at Cold Tire Inflation Pressure least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 201 Tire Loading And Tire Pressure This placard tells you important information about the: NOTE: 1. Number of people that can be carried in the The proper cold tire inflation pressure is listed on vehicle. the driver’s side B-Pillar or the rear edge of the 2.
Page 202 To determine the maximum loading conditions of (4) The resulting figure equals the available Metric Example For Load Limit your vehicle, locate the statement “The combined amount of cargo and luggage load capacity. For example, if “XXX” amount equals 635 kg and weight of occupants and cargo should never exceed For example, if “XXX”...
Page 204: Tires - General Information
Safety NOTE: WARNING! • Unequal tire pressures from side to side may cause WARNING! Overloading of your tires is dangerous. Over- erratic and unpredictable steering response. loading can cause tire failure, affect vehicle han- • Unequal tire pressure from side to side may cause •...
Page 205 At least once a month: Tire pressures change by approximately 1 psi (7 kPa) WARNING! per 12°F (7°C) of air temperature change. Keep this • Check and adjust tire pressure with a good quality in mind when checking tire pressure inside a garage, High speed driving with your vehicle under pocket-type pressure gauge.
Page 206 ∕ • The puncture is no greater than a of an inch NOTE: WARNING! (6 mm). TPM Sensor must be replaced after driving the stuck, and do not let anyone near a spinning vehicle on a flat tire condition. Consult an authorized tire dealer for tire repairs and wheel, no matter what the speed.
Page 207 Refer to “Replacement Tires” in this section for NOTE: It is recommended to replace the two front tires or further information. Wheel Valve Stem must be replaced as well when two rear tires as a pair. Replacing just one tire can installing new tires due to wear and tear in existing seriously affect your vehicle’s handling.
Page 208: Tire Types
MS designation on the tire sidewall. Use all season WARNING! WARNING! tires only in sets of four; failure to do so may ad- injury or death. Driving too fast for conditions sizes with load ratings approved for your ve- versely affect the safety and handling of your ve- also creates the possibility of loss of vehicle con- hicle.
Page 209: Spare Tires - If Equipped
(120 km/h) refer to original equipment or an autho- Refer to the “Towing Requirements - Tires” in Since this tire has limited tread life, the original rized tire dealer for recommended safe operating “Starting And Operating” in the Owner’s Manual equipment tire should be repaired (or replaced) and speeds, loading and cold tire inflation pressures.
Page 210 description on the Tire and Loading Information hicle handling. Since it is not the same as your WARNING! Placard located on the driver’s side door opening or original equipment tire, replace (or repair) the origi- Be sure to follow the warnings, which apply to on the sidewall of the tire.
Page 211: Wheel And Wheel Trim Care
Wheel And Wheel Trim Care NOTE: CAUTION! If you intend parking or storing your vehicle for an All wheels and wheel trim, especially aluminum and Only car wash soap, Mopar Wheel Cleaner or extended period after cleaning the wheels with chrome plated wheels, should be cleaned regularly equivalent is recommended.
Page 212: Department Of Transportation Uniform Tire Quality Grades
DEPARTMENT OF tive performance of tires depends upon the Temperature Grades actual conditions of their use, however, and TRANSPORTATION The Temperature grades are A (the high- may depart significantly from the norm due est), B, and C, representing the tire's resis- UNIFORM TIRE QUALITY to variations in driving habits, service prac- tance to the generation of heat and its abil-...
Page 213 WARNING! The temperature grade for this tire is es- tablished for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, ei- ther separately or in combination, can cause heat buildup and possible tire fail- ure.
Page 214: Wheel And Tire Torque Specifications
WHEEL AND TIRE Inspect the wheel mounting surface prior to mount- After 25 miles (40 km) check the lug nut/bolt ing the tire and remove any corrosion or loose torque to be sure that all the lug nuts/bolts are TORQUE particles.
Page 215: Fluid Capacities
FLUID CAPACITIES U.S. Metric Fuel (Approximate) 3.6L Engines 16.5 Gallons 62 Liters Engine Oil With Filter 3.6 Liter Engine (SAE 0W-20 , API Certified) 5 Quarts 4.7 Liters Cooling System* 3.6 Liter Engine Coolant (Mopar Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula with deion- 14.6 Quarts 13.8 Liters ized, or distilled water for proper corrosion protection)
Page 216: Fluids And Lubricants
FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) with deionized, or distilled water for proper corrosion protection or equivalent meeting the requirements of FCA Material Standard MS.90032.
Page 217: Chassis
CAUTION! CAUTION! CAUTION! additional rust inhibitors or antirust products, ant (antifreeze). If a non-OAT engine coolant • Mixing of engine coolant (antifreeze) other as they may not be compatible with the radia- (antifreeze) is introduced into the cooling sys- than specified Organic Additive Technology tor engine coolant and may plug the radiator.
Page 218: Mopar Accessories
MOPAR ACCESSORIES • In choosing Authentic Accessories you gain far • For the full line of Authentic Chrysler Accessories more than expressive style, premium protection, by Mopar visit your local dealership or online at Authentic Accessories By Mopar or extreme entertainment, you also benefit from mopar.com for U.S.
Page 219 ELECTRONICS: • Remote Start • Mopar Connect (WiFi) • Wireless Phone Charger • Electronic Vehicle Tracking System • Overhead DVD Player Media System CARRIERS: • Hitch-mount Bike Carrier • Roof Mount Bike Carrier • Roof Mount Cargo Carrier • Roof Mount Ski and Snowboard Carrier •...
Page 220: Cybersecurity
CYBERSECURITY • To help further improve vehicle security and mini- WARNING! mize the potential risk of a security breach, vehicle Your vehicle may be a connected vehicle and may owners should: • It is not possible to know or to predict all of the be equipped with both wired and wireless networks.
Page 221: Tips Controls And General Information
TIPS CONTROLS AND • Push the button in the center to select the next • Never use alcohol, gas and derivatives to clean the preset station (radio) or to change CDs if display lens. GENERAL equipped with a CD Player. •...
Page 222 3rd Row USB Charging Port Front Center Stack AUX Jack And USB Ports NOTE: 1 — USB Port 2 — Aux Jack Center Console USB Charging Port The USB “Charge Only” ports will recharge battery operated USB devices when connected. NOTE: There are multiple USB “charge only”...
Page 223: Uconnect Theater - If Equipped
UCONNECT THEATER — Getting Started There are three different ways to operate the fea- tures of the Uconnect Theater: IF EQUIPPED • The Remote Control Uconnect Theater Overview • The Uconnect System Your Uconnect Theater is designed to give your •...
Page 224: Unpairing The Remote
5. Test to make sure the remote is successfully 2. Press the “Remote” button towards the bottom 1. Gesture Pad — Control pointer position by run- of the Uconnect Theater touchscreen, within the paired by dragging your finger across the ges- ning your finger over this area and tapping to settings menu.
Page 225: General Information
9. Screen Selector Button — Push the screen se- 3. Install new batteries, making sure to orient them Play A DVD/Blu-ray Or USB Media lector to toggle between screen 1 (Driver Side), according to the polarity diagram shown inside File From Uconnect System or screen 2 (Passenger Side).
Page 226 5. To play a DVD/Blu-ray disc on both screens NOTE: After selecting “Press to Enter” or the Movie Snap- simultaneously, select “Disc” from both screen shot, the control functions for that screen appears. drop downs, or choose “Disc Source” on one These controls only apply to the individual screen screen and push the “View Screen”...
Page 227: Disc Menu
5. Listen In Uconnect Theater Apps Select the Apps source card to play pre-loaded games. Pressing the “Help” button teaches users Select this button to play one of the rear how to play each game. Pick from games: screens audio over the vehicle’s audio system. •...
Page 228: Using The Rear Video Usb Port
Are We There Yet? — Uconnect 4C NAV Using The Rear Video USB Port NOTE: To view USB media on the rear theater screens, insert a USB drive into the port next to the DVD/ Blu-ray disc player. The USB drive port is located under the radio controls in the instrument panel.
Page 229: Play Video Games
Play Video Games NOTE: Certain high-end video games will exceed the Connect the video game console to the HDMI 1 or power limit of the vehicle's Power Inverter. Refer to 2 ports, located behind the first row seat. “Power Inverter” in “Getting To Know Your Vehicle” in this guide for further information.
Page 230 NOTE: To replace the batteries: Uconnect Theater must be turned on before sound 1. Locate the battery compartment on the left ear can be heard from the headphones. To conserve cup of the headphones, and then slide the bat- battery life, the headphones will automatically turn tery cover downward.
Page 231: Display Settings
REGARDING DEFECTIVE PRODUCTS, AND What Does This Warranty Not Cover? This war- Wireless Streaming — If Equipped IS IN LIEU OF ALL OTHER WARRANTIES (EX- ranty does not cover any damage or defect that Your Uconnect Theater System may be equipped PRESS OR IMPLIED), INCLUDING ANY WAR- results from misuse, abuse or modification of the with Wireless Streaming functionality that allows...
Page 232 NOTE: Your phone will be added as an additional source Refer to your device's Owners Manual or card on the Uconnect Theater touchscreens. www.uconnectphone.com for further informa- NOTE: tion. The Authentication Screen will appear on both rear 3. Select “Pacifica Wireless Network” from the list touchscreens.
Page 233 Settings Refer to the Wireless Streaming video on the Uconnect YouTube Channel at www.youtube.com/ Below is a list of the settings available for the Wire- DriveUconnect for tips and additional information less Streaming feature of your Uconnect Theater on the Wireless Streaming function. system: Wireless Streaming Settings •...
Page 234: If You Need Assistance
IF YOU NEED • If an authorized dealer is unable to resolve the In Mexico Contact concern, you may contact the manufacturer's cus- ASSISTANCE Av. Prolongacion Paseo de la Reforma, 1240 tomer center. Sante Fe C.P. 05109 The manufacturer and its authorized dealer are vi- Any communication to the manufacturer's cus- tally interested in your satisfaction.
Page 235: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
Customer Assistance For The Hearing Vehicle Limited Warranty expires. The manufac- We appreciate that you have made a major invest- Or Speech Impaired (TDD/TTY) turer stands behind only the manufacturer's service ment when you purchased the vehicle. An autho- contracts. If you purchased a manufacturer's service rized dealer has also made a major investment in To assist customers who have hearing difficulties, contract, you will receive Plan Provisions and an...
Page 236: Reporting Safety Defects
• The Owner's Manual and User Guide electronic 1-800-333-0510 http:// LLC. files are also available on the Chrysler, Jeep, Ram Truck, Dodge and SRT websites. www.tc.gc.ca/roadsafety/. • Click on the “For Owners” tab, select “Owner/ Service Manuals”. Then select your desired model...
Page 237: Index
INDEX Accessories ....216 Air Pressure Jump Starting ....184 Mopar .
Page 238 Child Restraint ....118 Delay (Intermittent) Wipers ...47 Overheating ....187 Child Restraints Diagnostic System, Onboard .
Page 239 Octane Rating ....214 Intermittent Wipers (Delay Wipers) ..47 Brake Warning ....77 Specifications .
Page 240 Maintenance ....63 Recommendation ....213 Radio Frequency Viscosity ....213 Maintenance Schedule .
Page 241 Safety Tips ....134 Heated ....37 Starting.
Page 242 Changing ....174, 195 Wheel Nut Torque ....212 Uniform Tire Quality Grades ..210 Compact Spare .
Page 243 This guide has been prepared to help you get quickly acquainted with your new Chrysler brand vehicle and to provide a convenient reference for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation/Uconnect manuals found on the website on the back cover and other Warning Labels in your vehicle.
Page 244 Simply download the app, select your make and model and enjoy the ride. To get this app, go directly to the App Store® or Google Play® Store and enter the search keyword “Chrysler” (U.S. residents only). www.chrysler.com/en/owners (U.S.) provides special offers tailored to your needs, customized vehicle galleries, personalized service records and more.

Chrysler PACIFICA HYBRID 2019 User Manual

How to Find Your Owner's Manual Online

How to Use this Manual How to Use this Manual

Warnings and Cautions

Graphical Table of Contents

Instrument Panel

Interior

Gettingtoknow Yourvehicle

High Voltage Battery

High Voltage Charging Operation

Keys

Ignition Switch

Remote Starting System - if Equipped

Vehicle Security Alarm - if Equipped

Doors

Seats

Head Restraints

Steering Wheel

Mirrors

Exterior Lights

Windshield Wiper and Washers

Climate Controls

Windows

Panoramic Sunroof - if Equipped

Hood

Liftgate

Universal Garage Door Opener (Homelink)

Internal Equipment

Instrument Cluster Display

Warning Lights and Messages

Onboard Diagnostic System - Obd

Safety Features

Auxiliary Driving Systems

Occupant Restraint Systems

Safety Tips

Starting the Vehicle

Engine Break-In Recommendations

Park Brake

Automatic Transmission

Speed Control

Adaptive Cruise Control (Acc) - if Equipped

Parksense Rear Park Assist - if Equipped

Parksense Front and Rear Park Assist - if Equipped

Parksense Active Park Assist System - if Equipped

Lanesense - if Equipped

Parkview Rear Back up Camera

Surround View Camera System - if Equipped

Refueling the Vehicle

Trailer Towing

Recreational Towing (Behind Motorhome, Etc.)

Hazard Warning Flashers

Bulb Replacement

Fuses

Jacking and Tire Changing

Tire Service Kit - if Equipped

Jump Starting

Refueling in Emergency

If Your Engine Overheats

Freeing a Stuck Vehicle

Towing a Disabled Vehicle

Enhanced Accident Response System (Ears)

Event Data Recorder (Edr)

Servicingand Maintenance

Scheduled Servicing

Engine Compartment - Hybrid

Raising the Vehicle

Tires

Department of Transportation Uniform Tire Quality Grades

Wheel and Tire Torque Specifications

Fluid Capacities

Fluids and Lubricants

Mopar Accessories

Cybersecurity

Tips Controls and General Information

Aux/Usb/Mp3 Control

Uconnect Theater - if Equipped

Customerassistance

If You Need Assistance

Reporting Safety Defects

Publication Order Forms