Page 1 O W N E R ’ S M A N U A L 2 0 2 4 C H R Y S L E R P A C I F I C A...
Page 2 Please disregard any features CALL 1-800-521-2779 OR VISIT CHRYSLER.RSAHELP .COM (USA) and equipment described in this manual that are not on this vehicle. FCA US CALL 1-800-363-4869 OR VISIT FCA.ROADSIDEAID.COM (CANADA)
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION................7 GETTING TO KNOW YOUR VEHICLE.
Page 4 REMOTE START SYSTEM (BEV) — IF EQUIPPED . . . 27 INTRODUCTION Plastic Grocery Bag Retainer Hooks ..53 How To Use Remote Start ... . . 27 Head Restraints .
Page 5 INTERIOR STORAGE AND EQUIPMENT ..77 Canadian/Gate Operator Programming ..61 GETTING TO KNOW YOUR Storage ..... . . 77 Security .
Page 6 ALL-WHEEL DRIVE (AWD) — IF EQUIPPED ..134 STARTING AND OPERATING LaneSense Warning Message ..153 ACTIVE NOISE CANCELLATION ... . 134 Changing LaneSense Status .
Page 7 MULTIMEDIA Using The Video USB Port ... . 190 Periodic Safety Checks You Should Play Video Games ....191 Make Outside The Vehicle .
Page 8 SERVICING AND MAINTENANCE Snow Traction Devices ....302 Materials Added To Fuel ... . . 311 Tire Rotation Recommendations .
Page 9: Introduction
FCA US LLC aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. When it comes to service, remember that authorized dealers know your Chrysler vehicle best, have factory-trained technicians, genuine Mopar® parts, and care about your satisfaction.
Page 10: Symbols Key
INTRODUCTION SYMBOLS KEY VEHICLE MODIFICATIONS/ALTERATIONS WARNING! WARNING! These statements apply to operating pro- cedures that could result in a collision, Any modifications or alterations to this vehicle could seriously affect its roadworthi- bodily injury and/or death. ness and safety and may lead to a collision resulting in serious injury or death. CAUTION! These statements apply to procedures that could result in damage to your...
Page 11 INTRODUCTION Red Warning Lights Red Warning Lights Door Open Warning Light Oil Pressure Warning Light page 111 page 112 Electric Power Steering Fault Warning Light Oil Temperature Warning Light page 112 page 112 Electronic Throttle Control (ETC) Warning Light Seat Belt Reminder Warning Light page 112 page 113 Engine Coolant Temperature Warning Light...
Page 12 INTRODUCTION Red Warning Lights Yellow Warning Lights Plug Status Fault Warning Light Electronic Stability Control (ESC) OFF Warning Light page 113 page 114 Engine Check/Malfunction Indicator Warning Light Torque Limited Warning Light page 113 page 114 Yellow Warning Lights Fuel Level Sensor Fail Warning Light page 115 Adaptive Cruise Control (ACC) Fault Warning Light page 114...
Page 13 INTRODUCTION Yellow Warning Lights Green Indicator Lights Adaptive Cruise Control (ACC) Set With Target Vehicle Detected Indi- Service AWD Warning Light cator Light page 115 page 116 Service Forward Collision Warning (FCW) or Pedestrian Emergency Adaptive Cruise Control (ACC) Set With No Target Detected Indicator Braking (PEB) Warning Light Light page 115...
Page 14 INTRODUCTION Green Indicator Lights White Indicator Lights Parking/Headlights On Indicator Light Cruise Control Ready Indicator Light page 116 page 117 LaneSense Indicator Light Turn Signal Indicator Lights page 116 page 117 Max Regeneration Indicator Light Set Speed Display Indicator Light page 117 page 117 Blue Indicator Lights...
Page 15: Getting To Know Your Vehicle
GETTING TO KNOW YOUR VEHICLE Disposal of the High Voltage Battery HIGH VOLTAGE BATTERY WARNING! Your vehicle’s high voltage battery is designed to last • the life of your vehicle. See an authorized dealer for Your vehicle is equipped with a Lithium-ion high voltage Never try to remove the high voltage battery ser- information on the disposal of the battery if it should battery that is used to power the electric powertrain...
Page 16: Battery Conditioning
GETTING TO KNOW YOUR VEHICLE NOTE: • If the vehicle is plugged in at these battery tempera- WARNING! tures, the instrument cluster will display the mes- • During vehicle start up and shut down, a clicking sage “Please Leave Key In RUN — Battery Condition- Since the fluid leak may be Lithium Manganate noise may be heard from within the vehicle.
Page 17: High Voltage Charging Operation
GETTING TO KNOW YOUR VEHICLE HIGH VOLTAGE CHARGING OPERATION WARNING! Please be sure to follow these warnings. Failure to do SAE J1772 CHARGING INLET so may result in serious injury or death. • Discontinue use of the Portable Charging Cordset Your vehicle uses an industry standard SAE (EVSE) immediately if the plug or outlet becomes J1772 charge inlet (vehicle charge inlet) for both AC...
Page 18: Ac Level 2 Charging (240 Volt, 32 Amp)
GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! WARNING! After use, the Portable Charging Cordset (EVSE) should • • be placed in the storage bag and put back in the cargo Do not put fingers or objects into the Portable Ensure that the Portable Charging Cordset (EVSE) area storage bin if equipped.
Page 19: Vehicle Charge Indicators
GETTING TO KNOW YOUR VEHICLE When using public charging stations, ensure the charg- VEHICLE CHARGE INDICATORS ing station is ready to provide charge and the vehicle is Instrument Cluster High Voltage Battery Display in PARK before the Level 2 EVSE is plugged into the vehicle’s charge inlet.
Page 20: Hybrid Electric App
GETTING TO KNOW YOUR VEHICLE • HYBRID ELECTRIC APP Battery - Shows the amount of power (in kW) the Number Of Indicator Percent Of Battery high voltage battery is currently providing/ Lights Illuminated Charge Within the Uconnect system is the Hybrid Electric App absorbing.
Page 21 GETTING TO KNOW YOUR VEHICLE 2. Select the schedule to be set (1, 2, or 3) by pressing the appropriate arrow on the right side of the screen. 3. Select “Charge Schedule”. Driving History Screen Set Charge Schedule Charging Schedule 6.
Page 22: Keys
GETTING TO KNOW YOUR VEHICLE the week set in the schedule. Otherwise, charging KEYS will automatically begin when the selected charge time/day of the week occurs or whenever the KEY FOB vehicle is plugged in with no charge schedule set. •...
Page 23 GETTING TO KNOW YOUR VEHICLE Key Left Vehicle Feature NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate • If a valid key fob is no longer detected inside the vehicle A low key fob battery condition may be indicated by for further information.
Page 24: Sentry Key
GETTING TO KNOW YOUR VEHICLE 4. Fit a new battery ensuring that the positive (+) side are programmed to the vehicle can be used to start and WARNING! is facing upwards. Push the battery into the pocket operate the vehicle. The system cannot reprogram a until it is firmly seated in place and secured under key fob obtained from another vehicle.
Page 25: Ignition Switch
GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH The push button ignition can be placed in the following modes: KEYLESS ENTER ‘N GO™ IGNITION • The engine is stopped If applicable, refer to the “Hybrid Supplement” for • Some electrical devices (e.g. power locks, alarm, additional information.
Page 26: Keyless Enter 'N Go™ Ignition - Hybrid Models Only
GETTING TO KNOW YOUR VEHICLE The START/STOP ignition button has four operating The ignition can be placed in the following positions: CAUTION! positions; three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and An unlocked car is an invitation for thieves.
Page 27: Remote Start - If Equipped
GETTING TO KNOW YOUR VEHICLE • REMOTE START — IF EQUIPPED When the hood is open with the ignition in ON/RUN, WARNING! post-START mode (eliminates unexpected engine start-ups) • If applicable, refer to the “Hybrid Supplement” for Do not leave the key fob in or near the vehicle, or additional information.
Page 28: To Exit Remote Start Mode
GETTING TO KNOW YOUR VEHICLE NOTE: • Pushing the Remote Start button a third time shuts the Vehicle Security Light flashing engine off. • Ignition in OFF position • For vehicles equipped with the Keyless Enter ‘n Go™ To drive the vehicle, push the unlock button, and place •...
Page 29: Remote Start Windshield Wiper De-Icer Activation - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: REMOTE START SYSTEM (BEV) — REMOTE START WINDSHIELD If the vehicle is equipped with a rear climate system, it WIPER DE-ICER ACTIVATION — IF EQUIPPED will remain off to allow for optimal front row IF EQUIPPED performance.
Page 30: To Exit Remote Start Mode
GETTING TO KNOW YOUR VEHICLE NOTE: • Malfunction Indicator Light (MIL) is off while vehicle SCHEDULED CABIN CONDITIONING is in propulsion system active (SCC) • With Remote Start, the vehicle will only run for • Electronic Throttle Control (ETC) Warning Light is not 15 minutes.
Page 31: Vehicle Security System - If Equipped
GETTING TO KNOW YOUR VEHICLE The SCC will continue for a maximum of 15 minutes 3. Select the schedule to be set (1,2, or 3) by pressing 7. Select the days that this SCC event will occur. The after the scheduled departure time. the appropriate arrow on the right side of the “Repeat”...
Page 32: To Arm The System
GETTING TO KNOW YOUR VEHICLE NOTE: TO ARM THE SYSTEM SECURITY SYSTEM MANUAL • The driver's door key cylinder and the liftgate button OVERRIDE Follow these steps to arm the Vehicle Security system: on the key fob cannot arm or disarm the Vehicle 1.
Page 33: Power Door Locks - If Equipped
GETTING TO KNOW YOUR VEHICLE If you push the power door lock switch while the ignition WARNING! is in the ACC or ON/RUN position, and any front door is • open, the power locks will not operate. This prevents When exiting the vehicle, always make sure the you from accidentally locking your key fob in the vehicle.
Page 34 GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: • If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door The vehicle will only unlock the doors when a valid Pas- • Either the driver door only or all doors will unlock handle, the unlock sensitivity can be affected, sive Entry key fob is detected inside the vehicle, and no when you grab hold of the front driver’s door handle,...
Page 35: Automatic Unlock Doors On Exit - If Equipped
GETTING TO KNOW YOUR VEHICLE To Unlock/Enter The Liftgate Do NOT grab the door handle when pushing the door MANUAL SLIDING SIDE DOOR handle button. This could unlock the door(s). The liftgate Passive Entry unlock feature is built into the The sliding door may be opened from the inside or the electronic liftgate release handle.
Page 36: Power Sliding Side Door - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: • There is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep your • If anything obstructs the power sliding side door sliding door open on any incline. To close the sliding while it is closing or opening, the door will automati- door after the hold-open latch is activated, you must cally reverse to the closed or open position and an...
Page 37: Hands-Free Sliding Doors - If Equipped
GETTING TO KNOW YOUR VEHICLE • HANDS-FREE SLIDING DOORS — With every movement of the Hands-Free Sliding Doors, an audible tone will sound and the turn sig- IF EQUIPPED nals will flash. You can turn these alerts on or off in the Uconnect system page 169.
Page 38: Steering Wheel
GETTING TO KNOW YOUR VEHICLE • To avoid unintentional operation of the power slid- STEERING WHEEL WARNING! ing door from the rear seats, push the Sliding Door Power Off button, located in the overhead console. Do not adjust the steering column while driving. TILT/TELESCOPING STEERING When the overhead console power OFF LED is illumi- Adjusting the steering column while driving or driving...
Page 39: Driver Memory Settings - If Equipped
GETTING TO KNOW YOUR VEHICLE The Driver Memory Settings switch is located on the 1. Place the vehicle’s ignition in the ON/RUN position WARNING! driver door, next to the door handle, and consists of (do not start the engine). three buttons: •...
Page 40: Memory Position Recall
GETTING TO KNOW YOUR VEHICLE Manual Front Adjuster NOTE: SEATS Your key fob can be unlinked from your memory set- Both front seats are adjustable forward or rearward. tings by pushing the set (S) button, and then, within Seats are a part of the Occupant Restraint system of The manual seat adjustment handle is located under 10 seconds, pushing the unlock button on the key fob.
Page 41: Manual Adjustment Rear Seats
GETTING TO KNOW YOUR VEHICLE MANUAL ADJUSTMENT REAR SEATS While sitting in the seat, pull up on the handle and slide WARNING! the seat forward or rearward. Release the bar once you • have reached the desired position. Then, using body Seats should be adjusted before fastening the seat WARNING! pressure, move forward and rearward on the seat to be...
Page 42 GETTING TO KNOW YOUR VEHICLE To recline, lean forward slightly, lift the lever, and push The release strap is located on the front of the seat, back to the desired position and release the lever. Lean near the floor. To remove the seat, pull the release forward and lift the lever to return the seatback to its strap to release the rear latches.
Page 43 GETTING TO KNOW YOUR VEHICLE Easy Entry Easy Tilt Seat — With Or Without Child Seat Installed The second row seats can be tilted forward for easy entry into the third row with or without a child seat installed. 1. Located in the seatback of the second row seat is a lever (or handle for Stow ‘n Go seats) that provides easier access to the third row by tilting the seat forward.
Page 44 GETTING TO KNOW YOUR VEHICLE NOTE: This process is for when there is no child seat installed. Use the easy entry lever if a child seat is installed. Second Row Removable Quad Seat The second row quad seats, not equipped with the Stow ‘n Go feature, are removable for added cargo space.
Page 45 GETTING TO KNOW YOUR VEHICLE Seat Release Strap Seat Removal Installing Seat Reinstalling Seat 4. To remove the seat, pull the release strap to release 2. Tilt seat rearward to lock the seat back into its origi- the rear latches. nal position.
Page 46 GETTING TO KNOW YOUR VEHICLE Manually Folding Third Row Seats — To Unfold Third Row Seats 3. Pull release strap marked “2” and tumble the seat If Equipped rearward into the storage bin. 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the NOTE: anchors latch.
Page 47 GETTING TO KNOW YOUR VEHICLE A one-touch Auto Advance ‘n Return button is located 1. Push and release the Auto Advance ‘n Return WARNING! on the B-pillar trim panel, just in front of the power slid- button. ing door. • In a collision, you or others in your vehicle could be 2.
Page 48 GETTING TO KNOW YOUR VEHICLE SECOND ROW STOW 'N GO 2. Pull the latch located near the second row seat to 5. Fold the armrest upward and stow the seat by grab- open the floor panel. bing the strap on the lower part of the seatback, For Manual Seats: To stow the seat in the floor, move and guide the seat into the storage area.
Page 49 GETTING TO KNOW YOUR VEHICLE 7. Close the floor by pulling the floor panel backwards 1. To access the storage area, remove the floor mat WARNING! by the bottom corner edge of the panel. (if equipped) and place the lock rod in the unlocked position.
Page 50 GETTING TO KNOW YOUR VEHICLE 3. Pull the floor panel and position it toward the front 7. Lay the floor panel flat and push down until it clicks seats while folding the top half down and rest it into position. against the front seats.
Page 51: Power Adjustment Front Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE Reclining The Seatback POWER ADJUSTMENT FRONT WARNING! SEATS — IF EQUIPPED The angle of the seatback can be adjusted forward or • Do not ride with the seatback reclined so that the rearward. Push the seatback switch forward or rear- Some models may be equipped with eight-way power shoulder belt is no longer resting against your ward, the seat will move in the direction of the switch.
Page 52: Power Adjustment Rear Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE Power Lumbar — If Equipped • When the ignition is placed in the OFF position, the WARNING! driver seat will move about 2.4 inches (6.8 cm) rear- ward if the driver seat position is greater than or •...
Page 53 GETTING TO KNOW YOUR VEHICLE NOTE: To move the selected seat(s) to the normal (seated) position, push and release the “Normal” button. The • The outer head restraints will lower automatically as seat will automatically stop when the Normal position is necessary when the power seat begins to move.
Page 54: Heated Seats
GETTING TO KNOW YOUR VEHICLE Rear Heated Seats — If Equipped • 3. To abort seat operation while seat is in motion, push Press the heated seat button a third time to turn the a different seat position selector switch to stop the heating elements off.
Page 55: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: When the HI-level setting is selected, the heater will HEAD RESTRAINTS provide a boosted heat level during the initial stages of To remove the head restraint, raise it as far as it can go. Head restraints are designed to reduce the risk of injury operation.
Page 56 GETTING TO KNOW YOUR VEHICLE Head Restraints — Third Row WARNING! The outboard head restraints can be manually folded • ALL the head restraints MUST be reinstalled in the forward for improved rearward visibility. Pull the release vehicle to properly protect the occupants. Follow strap to fold them forward.
Page 57: Uconnect Voice Recognition - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: Use this QR code to access your digital experience. • The head restraints can be folded downward using the Head Restraint button or using the manual release strap. The head restraints must be raised manually when occupying the third row.
Page 58: Additional Information
GETTING TO KNOW YOUR VEHICLE Automatic Dimming Mirror — MIRRORS If Equipped INSIDE REARVIEW MIRROR The mirror head can be adjusted up, down, left, and right. The mirror should be adjusted to center on the Manual Mirror — If Equipped view through the rear window.
Page 59: Illuminated Vanity Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE ILLUMINATED VANITY MIRRORS — OUTSIDE MIRRORS WITH TURN IF EQUIPPED SIGNAL AND APPROACH LIGHTING — IF EQUIPPED To access an illuminated vanity mirror, flip down one of the visors and lift the cover. Driver and passenger outside mirrors with turn signal and approach lighting contain four LEDs, which are located in the upper outer corner of each mirror.
Page 60: Power Folding Outside Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: • The power mirror controls consist of mirror select but- Opening the door, then pushing the lock button on tons and a four-way mirror control switch. To adjust a the door panel, followed by closing the door. If the vehicle speed is greater than 10 mph (16 km/h), mirror, push either the L (left) or R (right) to select the •...
Page 61: Tilt Side Mirrors In Reverse - If Equipped
GETTING TO KNOW YOUR VEHICLE Use this QR code to access your digital TILT SIDE MIRRORS IN REVERSE — ERASING ALL THE HOMELINK® experience. IF EQUIPPED CHANNELS • HomeLink® replaces up to three Tilt Side Mirrors In Reverse provides automatic outside To erase the channels, follow this procedure: hand-held transmitters that operate mirror positioning which will aid the driver’s view of the...
Page 62: Programming Homelink® To A Garage Door Opener
GETTING TO KNOW YOUR VEHICLE NOTE: Rolling Code Garage Door Opener Final Steps WARNING! The “LEARN” or “TRAIN” button is not the button you NOTE: • normally use to operate the device. Do not run your vehicle in a closed garage or con- You have 30 seconds in which to initiate rolling code Non-rolling Code Devices fined area while programming the transmitter.
Page 63: Reprogramming A Single Homelink® Button
GETTING TO KNOW YOUR VEHICLE Reprogramming A Single HomeLink® Button REPROGRAMMING A SINGLE 1. Place the ignition in the ON/RUN position. (Canadian/Gate Operator) HOMELINK® BUTTON NOTE: To reprogram a channel that has been previously For vehicles equipped with Keyless Enter ‘n Go™, To reprogram a single HomeLink®...
Page 64: Exterior Lights
GETTING TO KNOW YOUR VEHICLE HEADLIGHT SWITCH WARNING! The headlight switch is located on the left side of the • Vehicle exhaust contains carbon monoxide, a dan- instrument panel. The switch controls the operation of gerous gas. Do not run your vehicle in the garage the headlights, parking lights, instrument panel lights, while programming the transmitter.
Page 65: Daytime Running Lights (Drls) - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: HIGH/LOW BEAM SWITCH For vehicles sold in Canada, rotate the headlight switch This system will not activate until the vehicle is at, or Push the multifunction lever toward the instrument clockwise from the parking light and instrument panel above 16 mph (25 km/h).
Page 66: Automatic Headlights - If Equipped
GETTING TO KNOW YOUR VEHICLE AUTOMATIC HEADLIGHTS — HEADLIGHT TIME DELAY — IF EQUIPPED IF EQUIPPED This system automatically turns your headlights on or This feature provides the safety of headlight illumina- off based on ambient light levels. To turn the system tion for up to 90 seconds after exiting your vehicle.
Page 67: Lane Change Assist - If Equipped
GETTING TO KNOW YOUR VEHICLE Turn Signal Warning Rear Courtesy/Reading Lights — INTERIOR LIGHTS If Equipped If the vehicle electronics sense that the vehicle has INTERIOR COURTESY LIGHTS traveled for about 1 mile (1.6 km) with the turn signals Located above the rear passengers are courtesy/reading on, a chime will sound and a message will display in the lights.
Page 68: Windshield Wiper And Washers
GETTING TO KNOW YOUR VEHICLE intermittent settings for high-speed wiper operation. To turn the switch at the end of the lever to select the turn the windshield wipers off, rotate the switch within desired delay interval. There are four delay settings, the lever all the way down to OFF.
Page 69: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE Neutral Wipe Inhibit — The Rain Sensing feature will • CLIMATE CONTROLS RAIN SENSING WIPERS — not operate when the ignition is ON, when the trans- IF EQUIPPED mission gear selector is in the NEUTRAL position The Climate Control system allows you to regulate the and the vehicle speed is less than 3 mph (5 km/h), This feature senses rain or snowfall on the windshield...
Page 70 GETTING TO KNOW YOUR VEHICLE AUTO Button NOTE: • Set your desired temperature and press the If the system is in Mix or Defrost Mode, the A/C can AUTO button on the touchscreen, or push the be turned off, but the A/C system shall remain button on the faceplate.
Page 71 GETTING TO KNOW YOUR VEHICLE Rear Defrost Button Touchscreen: Blower speed can be selected by • Push the blue button on the faceplate or touchscreen or press and slide the tempera- pressing the blower bar area between the icons. Press and release the Rear Defrost Control ture bar towards the blue arrow button on Press the desired blower speed from 1-7.
Page 72 GETTING TO KNOW YOUR VEHICLE Floor Mode FRONT CLIMATE BUTTON Air comes from the floor outlets. A slight Press and release the Front button to amount of air is directed through the defrost change the display on the Uconnect system and side window demister outlets.
Page 73 GETTING TO KNOW YOUR VEHICLE BLOWER CONTROL REAR PASSENGER CLIMATE CONTROL OFF 1. Adjust the rear blower, rear temperature and the rear modes to suit your comfort needs. BUTTON Blower Control is used to regulate the 2. ATC is selected by pushing the AUTO button. amount of air forced through the Climate Press and release the OFF button to turn the Control system.
Page 74: Manual Climate Control Descriptions And Functions
GETTING TO KNOW YOUR VEHICLE A/C Button REAR BLOWER CONTROL REAR CLIMATE CONTROL/BLOWER OFF The rear blower control can be manually set To manually set the rear blower controls to Press and release the A/C button to change to off, or any fixed blower speed by pushing off, press the Rear Climate Control/Blower the current setting.
Page 75 GETTING TO KNOW YOUR VEHICLE Continuous use of the Recirculation mode may make matically exit this feature. Pressing SYNC on the touch- CAUTION! the inside air stuffy and window fogging may occur. screen while in the Front Climate screen synchronizes Extended use of this mode is not recommended.
Page 76 GETTING TO KNOW YOUR VEHICLE Panel Mode Climate Control OFF Button REAR TEMPERATURE CONTROL These buttons provide the rear passengers with inde- Air comes from the outlets in the instrument Press and release this button to turn the pendent temperature control. panel.
Page 77 GETTING TO KNOW YOUR VEHICLE Rear Manual Temperature Control (MTC) PANEL MODE REAR TEMPERATURE CONTROL Press this button on the touchscreen to The rear Manual Temperature Control (MTC) system has To change the temperature in the rear of the change the air distribution mode to Panel floor air outlets at the rear right side of the third row vehicle, push temperature control up button Mode.
Page 78: Automatic Temperature Control (Atc) - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: OPERATING TIPS In many temperature positions, the Bi-Level mode is • It is not necessary to move the temperature settings Refer to the chart at the end of this section for sug- designed to provide cooler air out of the headliner out- for cold or hot vehicles.
Page 79: Interior Storage And Equipment
GETTING TO KNOW YOUR VEHICLE Cabin Air Filter Front Door Storage INTERIOR STORAGE AND EQUIPMENT The Climate Control system filters out dust and pollen Both interior front door panels have multiple pockets for from the air. Contact an authorized dealer to service storage.
Page 80 GETTING TO KNOW YOUR VEHICLE Storage Drawers — If Equipped Front Seatback Storage — If Equipped 1. To access the storage bins with front seats in the rearward position, place the lock rod in the unlocked There may be a storage drawer located in the lower cen- The front seatbacks have a storage pocket on some position so the load floor can fold upwards towards ter of the instrument panel, or as part of the center con-...
Page 81: Lighted Cupholders - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! WARNING! In the event of an individual being locked inside the • Do not drive the vehicle with the storage bin covers storage bin, the storage bin cover can be opened from In a collision, serious injury could result if the seat open.
Page 82: Usb/Aux Control
GETTING TO KNOW YOUR VEHICLE For example, if a device is plugged into the Type A USB port and another device is plugged into the Type C USB port, a message will appear and allow you to select which device to use. Sun Screen Extended Charge Only USB In The Center Console NOTE:...
Page 83: Power Outlets
GETTING TO KNOW YOUR VEHICLE POWER OUTLETS Your vehicle is equipped with 12 Volt (15 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets can be labeled with either a “key”...
Page 84 GETTING TO KNOW YOUR VEHICLE WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
Page 85: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE POWER INVERTER — IF EQUIPPED Your mobile phone must be designed for Qi® wireless WARNING! charging. If the phone is not equipped with Qi® wireless There is a 115 Volt, 150 W Power Inverter outlet charging functionality, an aftermarket sleeve or a spe- To avoid serious injury or death: located on the right side of the vehicle, before the third...
Page 86: Windows
GETTING TO KNOW YOUR VEHICLE • • If the phone moves on the pad causing the red light Do not place the key fob or any other type of metal/ The driver may lock out the rear power windows by push- to illuminate, the phone will have to be picked up magnetized object inside the mobile phone housing ing the bar control just below the power window controls.
Page 87: Automatic Window Features
GETTING TO KNOW YOUR VEHICLE NOTE: To close the window part way, lift the window switch WIND BUFFETING briefly and release it when you want the window to stop. The controls will not operate if the driver has activated Wind buffeting can be described as the perception of the Power Window Lockout.
Page 88: Opening And Closing The Sunroof
GETTING TO KNOW YOUR VEHICLE NOTE: Push the sunshade close switch and release it within WARNING! one second and the sunshade will close automatically • During Express Open or Express Close operation, from any position. If the sunroof is completely closed, •...
Page 89: Venting Sunroof
GETTING TO KNOW YOUR VEHICLE NOTE: HOOD 3. Push the safety latch release lever toward the pas- senger side of the vehicle. The safety latch is If three consecutive sunroof close attempts result in located behind the center front edge of the hood. Pinch Protect reversals, Pinch Protect will disable and OPENING the sunroof must be closed in Manual Mode.
Page 90: Closing
GETTING TO KNOW YOUR VEHICLE • For Hybrid models: Electric drive mode will not be LIFTGATE TO LOCK/CLOSE THE LIFTGATE available while the hood is open. A message will To manually close the liftgate, grab the liftgate closing show in the instrument cluster display to alert the handle and pull in a downward motion.
Page 91: Hands-Free Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: Push the Power Liftgate button on the overhead con- sole to open or close the liftgate. If the power liftgate will not fully open or latch close, • To open the liftgate, the Hands-Free Liftgate foot check the latch for damage or obstacles that may be Push the liftgate button on the key fob twice within five activation (if equipped) requires a valid Passive...
Page 92 GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With A Trailer Tow Package CAUTION! WARNING! NOTE: • The Hands-Free Liftgate feature may be turned on or Driving with the liftgate open can allow poisonous If your vehicle is equipped with the Trailer Tow Package, off in Uconnect Settings.
Page 93: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE IMPORTANT SAFETY INSTRUCTIONS CARGO AREA FEATURES WARNING! Read all instructions before using. When using your Cargo Area Storage • Do not vacuum any flammable liquids, such as vacuum, basic precautions should be followed, includ- ing the following: gasoline, or use around explosive vapors.
Page 94 GETTING TO KNOW YOUR VEHICLE NOTE: 3. Install desired attachment if needed. WARNING! The vacuum system will run for 10 minutes off bat- tery power and then the vacuum will shut down. A This equipment incorporates parts such as switches, low battery indication light (LOW PWR) located below motors, or the like that tend to produce arcs or sparks the vacuum nozzle storage location will come on...
Page 95 GETTING TO KNOW YOUR VEHICLE 4. Push the vacuum on/off button located under WARNING! WARNING! the vacuum nozzle storage location. Use vacuum as needed. • Keep hair, loose clothing, fingers, and all parts of For in vehicle use ONLY. To reduce the risk of fire, body away from openings and moving parts.
Page 96 GETTING TO KNOW YOUR VEHICLE NOTE: Vacuum Troubleshooting • The debris bin must be fully installed and locked for the DO NOT use with any opening blocked. If an object vacuum to function properly. becomes lodged in the hose, attempt to fully extend Hose Access Port the hose in a straight line while the vacuum motor is running.
Page 97: Stow 'N Place Roof Rack - If Equipped
GETTING TO KNOW YOUR VEHICLE STOW ‘N PLACE ROOF RACK — 2. Open the small access panel on the upper right DEPLOYING THE CROSSBARS side, and unclip the hose from the hose access port by pushing the yellow vacuum hose release lever IF EQUIPPED 1.
Page 98: Stowing The Crossbars
GETTING TO KNOW YOUR VEHICLE STOWING THE CROSSBARS CAUTION! 1. Starting with one crossbar, completely loosen the Use care when removing and handling the crossbars thumb screws at both ends. Lift the crossbar away to prevent damage to the vehicle. from the matching letter to remove it from the deployed position.
Page 99 GETTING TO KNOW YOUR VEHICLE NOTE: 3. Then, position the crossbar along the correct side 5. Once the driver’s side crossbar is in place, tighten rail. Make sure the letters on the crossbar align with the thumb screws completely. • To help control wind noise, stow the crossbars in the the matching letters on the side rail.
Page 100 GETTING TO KNOW YOUR VEHICLE CAUTION! • Load should always be secured to cross bars first, with tie down loops used as additional securing points if needed. Tie loops are intended as supple- mentary tie down points only. Do not use ratchet- ing mechanisms with the tie loops.
Page 101: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 102 GETTING TO KNOW YOUR INSTRUMENT PANEL...
Page 103: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL Use this QR code to access your digital WARNING! experience. A hot engine cooling system is dangerous. You or oth- ers could be badly burned by steam or boiling cool- ant. You may want to call an authorized dealer for Scan me service if your vehicle overheats page 276.
Page 104: Instrument Cluster - Hybrid Models
GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — HYBRID MODELS...
Page 105: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL ○ INSTRUMENT CLUSTER 4. Left Reconfigurable Screen With Four Customer Pro- All Range Values: shows values for electric, grammable Options hybrid and total range, along with a white gauge DESCRIPTIONS ○ showing the total range. Efficiency Coach: This gauge provides visual ○...
Page 106: Instrument Cluster Display Location And Controls
GETTING TO KNOW YOUR INSTRUMENT PANEL • Right Arrow Button INSTRUMENT CLUSTER DISPLAY If the light turns on while driving, stop the vehicle in a Push and release the right safe location as soon as possible. Have the vehicle arrow button to LOCATION AND CONTROLS transported to an authorized dealer.
Page 107: Engine Oil Life
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: • This message will be displayed continuously INSTRUMENT CLUSTER DISPLAY • This procedure should only be performed after sched- Cannot be cleared with button press MENU ITEMS uled maintenance is completed. Resetting oil life other •...
Page 108 GETTING TO KNOW YOUR INSTRUMENT PANEL Driver Assist — If Equipped • If the Tire Pressure system requires service, “Service System Off Tire Pressure System” is displayed. • ACC Proximity Warning Push and release the up or down arrow button Tire PSI is an information only function and cannot be •...
Page 109 GETTING TO KNOW YOUR INSTRUMENT PANEL Efficiency Coach • • The gauge bar color will transition smoothly up and When Rotary Shifter is shifted back to P/R/N/D: ○ down, and have a gradual change based on Max Regen Telltale goes away ○...
Page 110 GETTING TO KNOW YOUR INSTRUMENT PANEL Fuel Economy Messages TRIP INFO PHEV Push and release the up or down Push and release the up or down Push and release the up or down arrow button arrow button arrow button until the Fuel Economy Menu item is highlighted in the until Trip Info is highlighted in the instrument cluster until Messages is highlighted in the instrument cluster display.
Page 111 GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER DISPLAY PHEV INSTRUMENT CLUSTER DISPLAY Upper Left or Upper Right SCREEN SETUP OPTIONS SCREEN SETUP OPTIONS None Compass Outside Temp (If Equipped) Left Side Lower Left or Lower Right Average (MPG, Time Range L/100km,...
Page 112: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL • BATTERY SAVER ON/BATTERY The following are electrical loads that may be switched The battery was used for an extended period with off (if equipped), and vehicle functions which can be the engine not running to supply radio, lights, char- SAVER MODE MESSAGE —...
Page 113: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL Brake Warning Light WARNING LIGHTS AND MESSAGES WARNING! This warning light monitors various brake The warning/indicator lights will illuminate in the instru- Driving a vehicle with the red brake light on is danger- functions, including brake fluid level and ment panel together with a dedicated message and/or ous.
Page 114 GETTING TO KNOW YOUR INSTRUMENT PANEL Electric Power Steering Fault Warning Liftgate Open Warning Light The light will come on when the ignition is placed in the Light ON/RUN or ACC/ON/RUN position and remain on briefly This warning light will illuminate when the as a bulb check.
Page 115: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Seat Belt Reminder Warning Light Vehicle Security Warning Light — NOTE: If Equipped This warning light indicates when the driver • Older or non-compliant J1772 EVSE models may not or passenger seat belt is unbuckled. When support charging of this vehicle.
Page 116 GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Fault Electronic Stability Control (ESC) OFF WARNING! Warning Light — If Equipped Warning Light — If Equipped A malfunctioning catalytic converter can reach higher This warning light will illuminate to indicate a This warning light indicates the ESC is off.
Page 117 GETTING TO KNOW YOUR INSTRUMENT PANEL Low Fuel Warning Light Service LaneSense Warning Light — Each tire, including the spare (if provided), should be If Equipped checked monthly when cold and inflated to the inflation When the fuel level reaches approximately pressure recommended by the vehicle manufacturer on 1.85 gal (7 L) this warning light will turn on, This warning light will illuminate when the...
Page 118: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped TPMS malfunctions may occur for a variety of reasons, GREEN INDICATOR LIGHTS including the installation of replacement or alternate The LaneSense indicator light illuminates Adaptive Cruise Control (ACC) Set With tires or wheels on the vehicle that prevent the TPMS solid green when both lane markings have from functioning properly.
Page 119: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Max Regeneration Indicator Light WHITE INDICATOR LIGHTS BLUE INDICATOR LIGHTS This indicator light will illuminate to indicate Adaptive Cruise Control (ACC) Ready High Beam Indicator Light that Max Regeneration is on and capable. Light — If Equipped This indicator light will illuminate to indicate that the high beam headlights are on.
Page 120: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL 2. As soon as you cycle the ignition switch to the ON WARNING! CAUTION! position, you will see the Malfunction Indicator Light ○ (MIL) symbol come on as part of a normal bulb Access, or allow others to access, information •...
Page 121: Starting And Operating
STARTING AND OPERATING NOTE: STARTING THE ENGINE NORMAL STARTING Only press one pedal at a time while driving the vehicle. To Turn On The Engine Using the ENGINE START/STOP Torque performance of the vehicle could be reduced if Before starting your vehicle, adjust your seat, adjust Button both pedals are pressed at the same time.
Page 122 STARTING AND OPERATING ALWAYS DO A VISUAL CHECK that your vehicle is in • Driver’s door is ajar WARNING! • Driver’s seat belt is unbuckled PARK by looking for the “P” in the instrument cluster Ensure that the vehicle is completely stopped, and •...
Page 123: Extended Park Starting
STARTING AND OPERATING The gear position indicator will blink continuously until WARNING! CAUTION! the gear selector is returned to the proper position, or • the requested shift can be completed. Do not leave the key fob in or near the vehicle (or To prevent damage to the starter, do not crank con- in a location accessible to children), and do not tinuously for more than 10 seconds at a time.
Page 124: Cold Weather Operation (Below -22°F Or −30°C)
STARTING AND OPERATING If the gear selector is not in PARK and the ENGINE WARNING! WARNING! START/STOP button is pushed once, the instrument • cluster will display a “Vehicle Not In Park” message • If the vehicle has a discharged battery, booster Do not leave children or animals inside parked and the engine will remain running.
Page 125: Autopark
STARTING AND OPERATING ALWAYS DO A VISUAL CHECK that your vehicle is in 3. The READY indicator will appear in the cluster when 4. Push the ENGINE START/STOP button a third time, the vehicle is in Ready to Drive mode, which may without brake pedal being pressed, to return the PARK by looking for the “P”...
Page 126 STARTING AND OPERATING AutoPark will engage when all of these conditions are WARNING! WARNING! met: • • • The transmission may not engage PARK if the Do not leave the key fob in or near the vehicle (or Vehicle is equipped with a gear selector vehicle is moving.
Page 127: After Starting
STARTING AND OPERATING If the driver shifts into PARK while moving, the vehicle ENGINE BLOCK HEATER — IF EQUIPPED 3. If the gear selector is not in PARK, with vehicle may park. speed less than 5 mph (8 km/h), when the ENGINE Park will engage ONLY when vehicle speed is 1.2 mph START/STOP button is pushed, the instrument clus- The engine block heater warms the engine and permits...
Page 128: Engine Break-In Recommendations
STARTING AND OPERATING PARKING BRAKE in the instrument cluster and an indicator on the switch WARNING! will illuminate. If your foot is on the brake pedal while you apply the parking brake, you may notice a small Remember to disconnect the engine block heater ELECTRIC PARK BRAKE (EPB) amount of brake pedal movement.
Page 129 STARTING AND OPERATING NOTE: In the unlikely event of a malfunction of the EPB sys- WARNING! tem, a yellow EPB Warning Light will illuminate. This When parking on a hill, it is important to turn the front • may be accompanied by the Brake Warning Light flash- wheels toward the curb on a downhill grade and away Always fully apply the parking brake when leaving ing.
Page 130: Automatic Transmission
STARTING AND OPERATING Brake Service Mode WARNING! WARNING! We recommend having your brakes serviced by an • It is dangerous to shift out of PARK or NEUTRAL if You can be badly injured working on or around a authorized dealer. You should only make repairs for the engine speed is higher than idle speed.
Page 131: Ignition Park Interlock
STARTING AND OPERATING 9-SPEED AUTOMATIC TRANSMISSION Only shift from DRIVE to PARK or REVERSE when the CAUTION! accelerator pedal is released and the vehicle is The transmission is controlled using a rotary electronic stopped. Be sure to keep your foot on the brake pedal Damage to the transmission may occur if the follow- gear selector located on the center console.
Page 132 STARTING AND OPERATING NEUTRAL (N) When parking on a hill, apply the parking brake before If the transmission becomes extremely hot, the Trans- shifting the transmission to PARK. As an added precau- mission Temperature Warning Light will illuminate, a Use this range when the vehicle is standing for prolonged tion, turn the front wheels toward the curb on a downhill warning message will appear in the instrument cluster, periods with the engine running.
Page 133: Automatic Transmission - Hybrid
STARTING AND OPERATING NOTE: In the event of a momentary problem, the transmission WARNING! can be reset to regain all forward gears by performing The torque converter clutch will not engage until the the following steps: • engine and/or transmission is warm (usually after 1 to It is dangerous to shift out of PARK or NEUTRAL if 3 miles [2 to 5 km] of driving).
Page 134: Ignition Park Interlock
STARTING AND OPERATING pressed. The brake pedal must also be pressed to shift CAUTION! from NEUTRAL (N) into DRIVE (D) or REVERSE (R) when the vehicle is stopped or moving at low speeds. Damage to the transmission may occur if the follow- ing precautions are not observed: HYBRID TRANSMISSION •...
Page 135 STARTING AND OPERATING NEUTRAL (N) DRIVE (D) NOTE: This vehicle incorporates an Electric Park Brake activa- Use this range when the vehicle is standing for pro- This range should be used for most city and highway tion feature which engages automatically when the longed periods with the propulsion system active.
Page 136: All-Wheel Drive (Awd) - If Equipped
STARTING AND OPERATING NOTE: 5. Restart the vehicle. ACTIVE NOISE CANCELLATION 6. Shift into the desired gear range. If the problem is • Driving the vehicle in LOW will make the transitions Your vehicle is equipped with an Active Noise Cancella- no longer detected, the transmission will return to between vehicle accelerating and coasting, as well tion system.
Page 137: Stop/Start System - If Equipped
STARTING AND OPERATING • If the “Service Power Steering" or "Power AUTOSTOP MODE Battery temperature is too warm or cold. Steering Assist Off - Service System” mes- • Battery charge is low. During this time a message The Stop/Start feature is enabled after every driver key sage and a steering wheel icon are displayed will display “Stop/Start Not Ready Battery start.
Page 138: To Start The Engine While In Autostop
STARTING AND OPERATING TO START THE ENGINE WHILE IN TO MANUALLY TURN OFF THE SYSTEM MALFUNCTION AUTOSTOP STOP/START SYSTEM If there is a malfunction in the Stop/Start system, the system will not shut down the engine. A “Service STOP/ While in a forward gear, the engine will start when the START System”...
Page 139: Cruise Control
STARTING AND OPERATING To Activate U.S. Speed (mph) CRUISE CONTROL Pushing the SET (+), or SET (-) button once will • Push the on/off button to activate the Cruise Control. When engaged, the Cruise Control takes over accelera- result in a 1 mph speed adjustment. Each subse- The Cruise Control Set Indicator Light in the instrument tor operations at speeds greater than 20 mph quent tap of the button results in an adjustment of...
Page 140: Adaptive Cruise Control (Acc)
STARTING AND OPERATING NOTE: WARNING! WARNING! • If the ACC sensor detects a vehicle ahead, ACC will • The ACC system: Cruise Control can be dangerous where the system apply limited braking or accelerate (not to exceed ○ Does not react to pedestrians, oncoming cannot maintain a constant speed.
Page 141 STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation Adaptive Cruise Control (ACC) Menu Activating Adaptive Cruise Control (ACC) The buttons on the right side of the steering wheel The instrument cluster displays the current ACC system The minimum set speed for the ACC system is 20 mph operate the ACC system.
Page 142 STARTING AND OPERATING NOTE: The following conditions will only cancel the ACC WARNING! system: Fixed Speed Cruise Control cannot be set below • 20 mph (32 km/h). Driver seat belt is unbuckled at low speeds Leaving the Adaptive Cruise Control (ACC) system on If either system is set when the vehicle speed is above •...
Page 143 STARTING AND OPERATING NOTE: WARNING! When you override and push the SET (+) button or SET (-) buttons, the new set speed will be the current speed The Resume function should only be used if traffic of the vehicle. and road conditions permit. Resuming a set speed When ACC Is Active that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate...
Page 144 STARTING AND OPERATING ACC Operation At Stop Display Warnings And Maintenance The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the In the event that the ACC system brings your vehicle to “WIPE FRONT RADAR SENSOR”...
Page 145 STARTING AND OPERATING Precautions While Driving With ACC • Do not remove any screws from the sensor. Doing so The “ACC/AEB Limited Functionality Clean Front Wind- could cause an ACC system malfunction or failure shield” message can sometimes be displayed while In certain driving situations, ACC may have detection and require a sensor realignment.
Page 146 STARTING AND OPERATING TURNS AND BENDS LANE CHANGING When driving on a curve with ACC engaged, the system ACC may not detect a vehicle until it is completely in the may increase or decrease the vehicle speed for stabil- lane in which you are traveling. In the following lane ity, with no vehicle ahead detected.
Page 147: Parksense Front/Rear Park Assist System - If Equipped
STARTING AND OPERATING • PARKSENSE FRONT/REAR PARK ASSIST The automatic braking function can be enabled/ PARKSENSE SENSORS disabled from the Customer-Programmable Fea- The six ParkSense sensors (four when vehicle is not SYSTEM — IF EQUIPPED tures section of the Uconnect system. equipped with front sensors), located in the rear fascia/ •...
Page 148 STARTING AND OPERATING ParkSense Arcs 1 — No Tone/Solid Arc 6 — Fast Tone/Flashing Arc 2 — No Tone/Flashing Arc 7 — Fast Tone/Flashing Arc 3 — Fast Tone/Flashing Arc 8 — Slow Tone/Solid Arc 4 — Continuous Tone/Flashing Arc 9 —...
Page 149 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following charts show the warning alert operation when the system is detecting an obstacle: WARNING ALERTS FOR REAR Rear Distance Greater than 79-59 inches...
Page 150: Parksense Warning Display
STARTING AND OPERATING Front Park Assist Audible Alerts seconds. When the gear selector is moved to REVERSE These arc alerts will interrupt the "ParkSense Unavailable and the system is disabled, the instrument cluster dis- Wipe Rear Sensors", "ParkSense Unavailable Wipe Front ParkSense will turn off the Front Park Assist audible play will show the “ParkSense Off”...
Page 151: Parksense Active Park Assist System - If Equipped
STARTING AND OPERATING • PARKSENSE ACTIVE PARK ASSIST SYSTEM When you turn ParkSense off, the instrument clus- WARNING! ter will display “ParkSense Off.” Furthermore, once you turn ParkSense off, it remains off until you turn — IF EQUIPPED • Drivers must be careful when backing up even it on again, even if you cycle the ignition key.
Page 152: Enabling And Disabling The Parksense Active Park Assist System
STARTING AND OPERATING • • New vehicles from the dealership must have at least The liftgate is opened. PARALLEL/PERPENDICULAR 30 miles (48 km) accumulated before the • Electronic Stability Control/Anti-Lock Braking Sys- PARKING SPACE ASSISTANCE ParkSense Active Park Assist system is fully cali- tem intervention.
Page 153 STARTING AND OPERATING • The feature will only indicate the last detected park- ing space (example: if passing multiple available parking spaces, the system will only indicate the last detected parking space for the maneuver). When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a perpendicular or parallel parking sequence (depending on the type of...
Page 154: Lanesense - If Equipped
STARTING AND OPERATING NOTE: LANESENSE — IF EQUIPPED WARNING! • It is the driver’s responsibility to maintain a clear Drivers must be careful when performing parallel or line of sight with the instrument cluster display for LANESENSE OPERATION perpendicular parking maneuvers even when using driving instructions during a parking maneuver.
Page 155: Turning Lanesense On Or Off
STARTING AND OPERATING Left Lane Departure — Only Left Lane Detected Left Lane Departure — Both Lane Lines Detected TURNING LANESENSE ON OR OFF • • When the LaneSense system is on, the LaneSense When the LaneSense system is on, the lane lines The LaneSense button is located on the Telltale is solid white only when the left lane...
Page 156: Changing Lanesense Status
STARTING AND OPERATING NOTE: NOTE: The LaneSense system operates with similar behavior The ParkView Rear Back Up Camera has programmable for a right lane departure. modes of operation that may be selected through the Uconnect system page 169. CHANGING LANESENSE STATUS When the vehicle is shifted out of REVERSE with cam- era delay turned off, the rear camera mode is exited The LaneSense system has settings to adjust the inten-...
Page 157: Surround View Camera System - If Equipped
STARTING AND OPERATING NOTE: SURROUND VIEW CAMERA SYSTEM — When the vehicle is shifted out of REVERSE with cam- era delay turned off, the Surround View system is exited If snow, ice, mud, or any foreign substance builds up on IF EQUIPPED and the last known screen appears again.
Page 158 STARTING AND OPERATING Modes Of Operation When Zoom View is selected while the vehicle is in Rear View Plus Top View REVERSE, then shifted to DRIVE, the camera delay will Manual activation of the Surround View system is This is the default view of the system in display the standard Rear View.
Page 159: Famcam System - If Equipped
STARTING AND OPERATING NOTE: FAMCAM SYSTEM — IF EQUIPPED The display will appear in color in well-lit conditions and will appear black and white in low-light conditions. • If snow, ice, mud, or any foreign substance builds up If the driver shifts into REVERSE or presses the touch- Your vehicle may be equipped with a FamCam system on the camera lenses, clean the lenses, rinse with screen X button, the view will close.
Page 160: Refueling The Vehicle - Hybrid Models (If Equipped)
STARTING AND OPERATING NOTE: 1. Put the vehicle in PARK and switch the ignition OFF. REFUELING THE VEHICLE — HYBRID ○ After pushing the release button you will have 2. Push the center-rear edge of the fuel filler door MODELS (IF EQUIPPED) 20 minutes to fuel the vehicle;...
Page 161 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the Malfunction Indicator Light to turn on.
Page 162: Vehicle Loading
STARTING AND OPERATING Tire Size VEHICLE LOADING rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low The tire size on the Vehicle Certification Label repre- and be sure that the weight is distributed equally. Stow CERTIFICATION LABEL sents the actual tire size on your vehicle.
Page 163: Common Towing Definitions
STARTING AND OPERATING Weight-Distributing Hitch COMMON TOWING DEFINITIONS WARNING! A weight-distributing hitch works by applying leverage The following trailer towing related definitions will assist It is important that you do not exceed the maximum through spring (load) bars. They are typically used for you in understanding the following information: front or rear GAWR.
Page 164: Trailer Hitch Classification
STARTING AND OPERATING TRAILER HITCH CLASSIFICATION The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 165: Vehicle Loading Chart
STARTING AND OPERATING VEHICLE LOADING CHART Follow these steps to determine the total weight the vehicle can carry: 1. Determine the cargo capacity of your vehicle. ○ Load Capacity = GVWR – Curb (weight of vehicle, full fluids, no occupants). 2.
Page 166: Trailer And Tongue Weight
STARTING AND OPERATING Max Cargo With Max Max Trailer TW, Max Number Of Persons / Weight Of Occupants Max Cargo No Trailer Trailer TW 360 lb Trailer (163 kg) 455 lb (206 kg) – 360 lb (163 kg) = 95 lb (43 kg) 7 people / 1,050 lb (476 kg) 455 lb (206 kg)
Page 167 STARTING AND OPERATING Towing Requirements — Tires WARNING! WARNING! • Do not attempt to tow a trailer while using a com- • Improper towing can lead to a collision. Follow these Do not connect trailer brakes to your vehicle's pact spare tire. hydraulic brake lines.
Page 168: Towing Tips
STARTING AND OPERATING Cruise Control — If Equipped NOTE: Do not cut or splice wiring into the vehicle’s wiring • Do not use on hilly terrain or with heavy loads. harness. • When using the Cruise Control, if you experience The electrical connections are all complete to the speed drops greater than 10 mph (16 km/h), disen- vehicle but you must mate the harness to a trailer con-...
Page 169: Recreational Towing
STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE Towing Condition Wheel OFF The Ground FWD Models AWD Models NOT ALLOWED NOT ALLOWED Flat Tow NONE NOT ALLOWED Front Dolly Tow NOT ALLOWED NOT ALLOWED Rear On Trailer NOTE: 7.
Page 170: Driving Tips
STARTING AND OPERATING • DRIVING TIPS Keep tires properly inflated. WARNING! • Maintain sufficient distance between your vehicle • Driving through standing water limits your vehicle’s and the vehicle in front of you to avoid a collision in DRIVING ON SLIPPERY SURFACES braking capabilities, which increases stopping dis- a sudden stop.
Page 171: Multimedia
MULTIMEDIA UCONNECT SYSTEMS Your Uconnect system may also have SCREEN OFF and WARNING! MUTE buttons on the faceplate. • Push the SCREEN OFF button on the faceplate to turn For detailed information about your Uconnect 5 With ONLY insert trusted devices/components into your off the Uconnect screen.
Page 172 MULTIMEDIA NOTE: For The Uconnect 5 With 7-inch Display and The When making a selection, press the button on the Uconnect 5/5 NAV With 10.1-inch Display touchscreen to enter the desired menu. Once in the • Only one touchscreen area may be selected at a desired menu, press and release the preferred setting Press the Vehicle button, then press the Settings tab at time.
Page 173 MULTIMEDIA Setting Name Description Show Main Category Bar Labels This setting will allow the main category bar labels to be shown on or off. Navigation Next Turn Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display. Phone Pop-Ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.
Page 174 MULTIMEDIA Display After pressing the Display button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Language This setting will change the language of the Uconnect system and Instrument Cluster Display. The available languages are English, Français, Español, and Italiano.
Page 175 MULTIMEDIA Safety & Driving Assistance After pressing the Safety & Driving Assistance button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Forward Collision Warning Sensitivity — Located In This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.
Page 176 MULTIMEDIA Setting Name Description Hill Start Assist This setting will turn the Hill Start Assist system on or off. Rear Seat Alert When this setting is turned on and the rear doors are opened while the engine is running, or if the engine is turned on within 10 minutes of the door opening, a message will appear to check the rear seat when the vehicle is powered OFF.
Page 177 MULTIMEDIA Phone/Bluetooth® When the Phone/Bluetooth® button is pressed on the touchscreen, the system displays the options related to Bluetooth® connectivity from an external audio device or smart- phone. The list of paired audio devices or smartphones can be accessed from this menu. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 178 MULTIMEDIA Navigation — If Equipped When the Navigation button is pressed on the touchscreen, the system displays options related to the vehicle’s built-in Navigation system. These settings can change which icons display on the map, how “time to arrival is calculated”, and route types. For more information on Navigation and settings, refer to your Uconnect Radio Instruction Manual.
Page 179 MULTIMEDIA Mirrors & Wipers When the Mirrors & Wipers button is pressed on the touchscreen, the system displays the options related to the vehicle’s mirrors and wipers. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Tilt Side Mirrors In Reverse This setting will tilt the outside side-view mirrors when the ignition is in the ON/RUN position and the transmission gear selector is in the REVERSE position.
Page 180 MULTIMEDIA Setting Name Description Flash Lights With Lock This setting will allow you to turn the flashing of the lights when the Lock button is pushed on the key fob on or off. Auto Dim High Beams This setting will allow you to turn the Auto Dim High Beams on or off. Flash Lights With Sliding Door This setting will flash the lights when the sliding door reverses.
Page 181 MULTIMEDIA Setting Name Description Passive Entry This setting will allow you to turn the Passive Entry feature (Keyless Enter ‘n Go™) on or off. Personal Settings Linked To Key Fob This setting will recall preset radio stations and driver seat position that have been linked to the key fob. This setting will chime an audible alert when the power liftgate is raising or lowering.
Page 182 MULTIMEDIA Key Off Options When the Key Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff. These settings will only activate when the ignition is set to OFF. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Easy Exit Seat...
Page 183 MULTIMEDIA Setting Name Description Speed Adjusted Volume This setting will adjust audio volume as speeds increase. At a higher setting, the volume will increase more as the vehicle speeds up. The available settings are “Off”, “1”, “2”, and “3”. Surround Sound This setting will turn the Surround Sound system on or off.
Page 184 MULTIMEDIA SiriusXM® Setup When the SiriusXM® Setup button is pressed on the touchscreen, the system displays options related to SiriusXM® satellite radio. These settings can be used to skip specific radio channels and restart favorite songs from the beginning. NOTE: •...
Page 185 MULTIMEDIA Software Updates When the Software Updates button is pressed on the touchscreen, the system will display information on updating the Uconnect system’s software. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Software Downloads over Wi-Fi This setting will allow software updates to happen over Wi-Fi.
Page 186 MULTIMEDIA Reset When the Reset button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings. These settings can clear personal data and reset selected settings from other menus. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 187: Steering Wheel Audio Controls
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS The following describes the left-hand control operation Remote with Alexa to easily find, launch, and control in each mode: content. Check sports scores, play music, control smart home devices, or see your live camera feeds (compat- The remote sound system controls are located on the RADIO OPERATION ible smart home device required and sold separately).
Page 188: Getting Started
MULTIMEDIA GETTING STARTED ACCESSING REAR SEAT FIRST TIME STARTING UP (USING ENTERTAINMENT WITH FIRE TV THE REAR SCREENS) BUILT-IN FROM THE FRONT RADIO Boot-up Screen SCREEN When turning on the system for the first time from the rear screens, a boot-up screen will appear on the sys- You can access your Rear Seat Entertainment with Fire tem displaying the Fire TV logo.
Page 189: Alexa Voice Control
MULTIMEDIA NOTE: LISTEN VIA VEHICLE SPEAKERS PARENTAL CONTROLS (USING THE When a network is connected to the system for the first REAR SCREENS) A feature within Rear Seat Entertainment with Fire TV time, an over-the-air-software update will take place built-in is the front radio Listen feature. On the front using the Wi-Fi connection.
Page 190: Media Sources Input (Using The Front Radio And Rear Screens)
MULTIMEDIA 4. Home — Push to return to the Fire TV Home screen. 5. From this menu, select “Add New Remote”. VOICE REMOTE WITH ALEXA 5. Seek Backward/Rewind Button — Push and hold to 6. Follow the on-screen steps for Voice Remote with Alexa pairing.
Page 191: Rear Seat Entertainment With Fire Tv Built-In
MULTIMEDIA Replacing the Voice Remote with Alexa Fire TV Access Using Browse Media Batteries Selecting “Browse Media” on the front radio screen will Fire TV is your source for online streaming with Rear give access to different media within Rear Seat Enter- Seat Entertainment with Fire TV built-in.
Page 192: Play A Blu-Ray™ Or Dvd - If Equipped
MULTIMEDIA • Back — This will let you go back the previous page. 3. Select the Blu-ray™ or DVD under inputs in the FIRE TV APPS/GAMES (USING THE Fire TV Home — This will take you back to the Fire Launch Source menu •...
Page 193: Play Video Games
MULTIMEDIA NOTE: Wireless Headphones Pairing PLAY VIDEO GAMES Certain high-end video games may exceed the power To pair wireless headphones with Rear Seat Entertain- Connect the video game console to either of the HDMI limit of the vehicle's Power Inverter page 83.
Page 194 MULTIMEDIA Icon Description AUTO Button Automatically controls the rear interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between Manual mode and Automatic mode. Rear Passenger Temperature Up and Down Buttons Provides the rear passengers with independent temperature control.
Page 195: Legal & Compliance
MULTIMEDIA Icon Description Floor Mode Floor Mode Air comes from the floor outlets. Blower Control 1,2,3, etc. Blower Control is used to regulate the amount of air forced through the Climate system. There are seven blower speeds available. Adjusting the blower will cause Automatic mode to switch to Manual operation.
Page 196: Safety
SAFETY Anti-Lock Brake System (ABS) Warning SAFETY FEATURES WARNING! Light • The ABS contains sophisticated electronic equip- ANTI-LOCK BRAKE SYSTEM (ABS) The yellow ABS Warning Light will turn on when the igni- ment that may be susceptible to interference tion is placed in the ON/RUN mode and may stay on for caused by improperly installed or high output radio The ABS provides increased vehicle stability and brake as long as four seconds.
Page 197: Audible Pedestrian Warning System
SAFETY The RBS uses conventional hydraulic friction brakes, the Anti-Lock Brake System (ABS). Applying the brakes WARNING! regenerative braking, or a combination to slow the very quickly results in the best BAS assistance. To vehicle. If the system detects slippery conditions while receive the benefit of the system, you must apply con- The Audible Pedestrian Warning system is not braking, ONLY friction is used to slow the vehicle.
Page 198 SAFETY Dynamic Steering Torque (DST) ERM can only reduce the chance of wheel lift occurring The ESC Activation/Malfunction Indicator Light located during severe or evasive driving maneuvers; it cannot in the instrument cluster will start to flash as soon as DST is a feature of the ESC and Electric Power Steering prevent wheel lift due to other factors, such as road con- the ESC system becomes active.
Page 199 SAFETY ESC Operating Modes The ESC OFF Indicator Light indicates that WARNING! the Electronic Stability Control (ESC) is in a Depending upon model and mode of operation, the ESC • reduced mode. When in “Partial Off” mode, the TCS functionality system may have multiple operating modes.
Page 200 SAFETY Rear Seat Reminder Alert (RSRA) • The driver door must be closed. WARNING! • The vehicle must be on a sufficient grade. RSRA alerts you through a visual and auditory notifica- • • If you use a trailer brake controller with your trailer, The gear selection must match vehicle uphill direc- tion of the possible presence of an object, passenger, the trailer brakes may be activated and deacti-...
Page 201: Auxiliary Driving Systems
SAFETY Traction Control System (TCS) AUXILIARY DRIVING SYSTEMS The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.7 m). The The TCS monitors the amount of wheel spin of each of zone length starts at the outside rearview mirror and the driven wheels.
Page 202 SAFETY Entering From The Side The area on the rear fascia/bumper where the radar The BSM system notifies the driver of objects in the sensors are located must remain free of snow, ice, and detection zones by illuminating the BSM Warning Light Vehicles that move into your adjacent lanes from either dirt/road contaminants so the BSM system can func- located in the outside mirrors in addition to sounding...
Page 203 SAFETY Rear Cross Path (RCP) Overtaking Traffic The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foli- If you pass another vehicle slowly with a relative speed RCP is intended to aid the driver when backing out of age, berms, snow banks, car washes, etc.
Page 204: Forward Collision Warning (Fcw) With Mitigation - If Equipped
SAFETY NOTE: Blind Spot Alert Lights/Chime FORWARD COLLISION WARNING In a parking lot situation, oncoming vehicles can be When operating in Blind Spot Alert Lights/Chime mode, (FCW) WITH MITIGATION — blocked by vehicles parked on either side. If the sen- the BSM system will provide a visual alert in the appro- IF EQUIPPED sors are blocked by other structures or vehicles, the...
Page 205 SAFETY By changing the FCW status setting to "Far", the system WARNING! provides possible collision warnings on objects farther away. This results in earlier warnings and provides the Forward Collision Warning (FCW) is not intended to most reaction time to avoid possible collisions. avoid a collision on its own, nor can FCW detect every type of potential collision.
Page 206 SAFETY Pedestrian Emergency Braking (PEB) — • FCW may not react to irrelevant objects such as WARNING! overhead objects, ground reflections, objects not in If Equipped the path of the vehicle, stationary objects that are Pedestrian Emergency Braking (PEB) is not intended PEB is a subsystem of the FCW system which provides far away, oncoming traffic, or leading vehicles with to avoid a collision on its own, nor can PEB detect...
Page 207: Tire Pressure Monitoring System (Tpms)
SAFETY TIRE PRESSURE MONITORING The TPMS will continue to warn the driver of low tire CAUTION! pressure as long as the condition exists, and will not SYSTEM (TPMS) turn off until the tire pressure is at or above the recom- •...
Page 208 SAFETY SERVICE TPMS WARNING • Driving on a significantly underinflated tire causes 3. After driving the vehicle for up to 20 minutes above the tire to overheat and can lead to tire failure. 15 mph (24 km/h), the TPMS Warning Light will When a system fault is detected, the Tire Pressure Underinflation also reduces fuel efficiency and tire flash on and off for 75 seconds and then remain on...
Page 209: Occupant Restraint Systems
SAFETY TIRE PRESSURE MONITORING SYSTEM LOW TPMS DEACTIVATION — IF EQUIPPED OCCUPANT RESTRAINT SYSTEMS PRESSURE WARNINGS The Tire Pressure Monitoring System (TPMS) can be Some of the most important safety features in your deactivated if replacing all four wheel and tire assem- The TPMS Warning Light will illuminate in the vehicle are the restraint systems: blies (road tires) with wheel and tire assemblies that do...
Page 210: Seat Belt Systems
SAFETY BeltAlert Warning Sequence 4. Never allow children to slide the shoulder belt SEAT BELT SYSTEMS behind them or under their arm. The BeltAlert warning sequence is activated when the Buckle up even though you are an excellent driver, even vehicle is moving above a specified vehicle speed range 5.
Page 211 SAFETY NOTE: WARNING! WARNING! If BeltAlert has been deactivated and the driver or out- • • board front seat passenger (if equipped with outboard Do not allow people to ride in any area of your A seat belt that is buckled into the wrong buckle front passenger seat BeltAlert) is unbuckled the Seat vehicle that is not equipped with seats and seat will not protect you properly.
Page 212 SAFETY Lap/Shoulder Belt Operating 5. Position the shoulder belt across the shoulder and Instructions chest with minimal, if any, slack so it is comfortable and not resting on your neck. The retractor will with- draw any slack in the shoulder belt. 1.
Page 213 SAFETY Adjustable Upper Shoulder Belt 1. Remove the mini-latch plate and regular latch plate WARNING! Anchorage from its stowed position in the headliner slightly behind the second or third row seat. • Wearing your seat belt incorrectly could make your In the front and second row outboard seats the shoul- injuries in a collision much worse.
Page 214 SAFETY 3. Route the shoulder belt to the inside of the left head 5. Sit back in seat. Slide the regular latch plate up the 7. Position the lap belt so it is snug and lies low across restraint. webbing as far as necessary to allow the seat belt to your hips, below your abdomen.
Page 215 SAFETY Seat Belt Pretensioner WARNING! WARNING! The front outboard seat belt system is equipped with • Using a Seat Belt Extender when not needed can • If the mini-latch plate and mini-buckle are not pretensioning devices that are designed to remove increase the risk of serious injury or death in a properly connected when the seat belt is used by slack from the seat belt in the event of a collision.
Page 216 SAFETY Switchable Automatic Locking If the passenger seating position is equipped with an Retractors (ALR) ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap The seat belts in the passenger seating positions are around the occupant’s mid-section so as to not activate equipped with a Switchable Automatic Locking Retrac- the ALR.
Page 217 SAFETY Seat Belt Park Stitch — If Equipped Third Row Stow Clip — If Equipped How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. The rear outboard seat belts may be equipped with a Your vehicle may be equipped with a stow clip on the park stitch to raise the latch plate for easier access to lower trim behind the third row.
Page 218: Supplemental Restraint Systems (Srs)
SAFETY Air Bag Warning Light NOTE: SUPPLEMENTAL RESTRAINT If the speedometer, tachometer, or any engine related SYSTEMS (SRS) The Occupant Restraint Controller (ORC) gauges are not working, the Occupant Restraint Control- monitors the readiness of the electronic ler (ORC) may also be disabled. In this condition the air Some of the safety features described in this section parts of the air bag system whenever the bags may not be ready to inflate for your protection.
Page 219 SAFETY Front Air Bags This vehicle may be equipped with a driver and/or front WARNING! passenger seat belt buckle switch that detects whether This vehicle has front air bags and lap/shoulder belts the driver or front passenger seat belt is buckled. The •...
Page 220 SAFETY Front Air Bag Operation Occupant Classification Module (OCM) And Sensor The steering wheel hub trim cover and the upper pas- senger side of the instrument panel separate and fold The Occupant Classification Module (OCM) is located Front Air Bags are designed to provide additional pro- out of the way as the air bags inflate to their full size.
Page 221 SAFETY Do not decrease OR increase the front passenger’s * It is possible for a child to be classified as an adult, In order for the OCS to operate as designed, it is impor- seated weight on the front passenger seat allowing a full-power Passenger Advanced Front Air Bag tant for the front passenger to be seated properly and deployment.
Page 222 SAFETY The OCS determines the front passenger’s most prob- WARNING! able classification. If an occupant in the front passen- ger seat is seated improperly, the occupant may provide • Always wear your seat belt and sit properly, with an output signal to the OCS that is different from the the seatback in an upright position, your back occupant’s properly seated weight input, for example: against the seatback, sitting upright, facing for-...
Page 223 SAFETY Knee Impact Bolsters If the seat, trim cover, or cushion needs service for any The SABs may help reduce the risk of occupant injury reason, take the vehicle to an authorized dealer. Only during certain side impacts, in addition to the injury The Knee Impact Bolsters help protect the knees of the FCA US LLC approved seat accessories may be used.
Page 224 SAFETY Supplemental Side Air Bag Inflatable Curtains (SABICs) Side Air Bags are a supplement to the seat belt WARNING! restraint system. Side Air Bags deploy in less time than This vehicle is equipped with Supplemental Side Air Bag it takes to blink your eyes. Inflatable Curtains (SABICs).
Page 225 SAFETY NOTE: • • Driver and Front Passenger Air Bags As the air bags deflate, you may see some smoke- like particles. The particles are a normal by-product • Air bag covers may not be obvious in the interior trim, Seat Belt Buckle Switch of the process that generates the non-toxic gas used but they will open during air bag deployment.
Page 226 SAFETY Enhanced Accident Response System NOTE: In order to immediately reset the hazard flashers, inte- rior lights, power door locks, or the HVAC blower motor, After an accident, place the ignition in the STOP (OFF) In the event of an impact, if the communication net- the ignition switch must be changed from START or position to avoid draining the battery.
Page 227: Child Restraints
SAFETY Event Data Recorder (EDR) NOTE: CHILD RESTRAINTS This vehicle is equipped with an event data recorder • Everyone in your vehicle needs to be buckled up at all For additional information, refer to (EDR). The main purpose of an EDR is to record, in cer- http://www.nhtsa.gov/parents-and-caregivers or times, including babies and children.
Page 228 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger and who have not Either an Infant Carrier or a Convertible Child Restraint, Infants and Toddlers reached the height or weight limits of their child restraint facing rearward in a rear seat of the vehicle...
Page 229 SAFETY Older Children And Child Restraints If the answer to any of these questions was “no,” then WARNING! the child still needs to use a booster seat in this Children who are two years old or who have outgrown • vehicle.
Page 230 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Use Any Attachment Method Shown With An “X” Below Child + Child Restraint LATCH – Lower Anchors Seat Belt Only LATCH – Lower Anchors Seat Belt + Top Tether Only + Top Tether Anchor Anchor...
Page 231 SAFETY Seven Passenger Quad Seat LATCH Positions (Includes Eight Passenger LATCH Positions (Stow ‘n Go) Lower Anchorage Symbol 2 anchorages per seat- ing position Lower Anchorage Symbol 2 anchorages per seat- Top Tether Anchorage Symbol ing position Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of the What is the weight limit (child’s weight + weight of the child restraint)
Page 232 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH The child seat may touch the back of the front passenger seat if the Can the rear-facing child restraint touch the back of the front pas- child restraint manufacturer also allows contact. See your child senger seat? restraint owner’s manual for more information.
Page 233 SAFETY Locating The Upper Tether Anchorages There are tether strap anchorages located behind all second row seating positions. The third row has a tether anchor on the 40% seat for the right outboard position and in the center of the 60% seat for either the center or left outboard seating position.
Page 234 SAFETY To Install A LATCH-Compatible Child Restraint If the selected seating position has a Switchable Auto- matic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below. See page 233 to check what type of seat belt each seating position has.
Page 235 SAFETY How To Stow An Unused Switchable-ALR Installing Child Restraints Using The Lap/Shoulder Belt Systems For (ALR) Seat Belt: Vehicle Seat Belt Installing Child Restraints In This Vehicle When using the LATCH attaching system to install a Child restraint systems are designed to be secured in child restraint, stow all ALR seat belts that are not being vehicle seats by lap belts or the lap belt portion of a used by other occupants or being used to secure child...
Page 236 SAFETY Seven Passenger Quad Seat Automatic Locking Retractor Eight Passenger Automatic Locking Retractor (ALR) (ALR) Locations (Includes Stow ‘n Go) Locations ALR — Switchable Automatic Locking Retractor ALR — Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Top Tether Anchorage Symbol Frequently Asked Questions What is the weight limit (child’s weight + weight of the child restraint) Always use the tether anchor when using the seat belt to install a...
Page 237 SAFETY Installing A Child Restraint With A NOTE: bing to retract back into the retractor. As the web- Switchable Automatic Locking Retractor bing retracts, you will hear a clicking sound. This If the folding, non-adjustable head restraint interferes means the seat belt is now in the Automatic Locking with the installation of the child restraint, the head (ALR): mode.
Page 238 SAFETY Installing Child Restraints Using The Top Tether Anchorage WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat.
Page 239 SAFETY To connect the tether strap hook to the tether anchor- age for either seating position on the 60% third row seat: 1. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.
Page 240: Safety Tips
SAFETY WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, It is not possible to know or to predict all of the pos- inside or outside of a vehicle. In a collision, people sible outcomes if your vehicle’s systems are riding in these areas are more likely to be seriously breached.
Page 241: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY Defroster WARNING! WARNING! Check operation by selecting the defrost mode and • • ONLY install floor mats designed to fit your vehicle. It is recommended to only use mild soap and water place the blower control on high speed. You should be NEVER install a floor mat that cannot be properly to clean your floor mats.
Page 242: Exhaust Gas
SAFETY Fluid Leaks Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected Check area under the vehicle after overnight parking for inside the vehicle, or when the underside or rear of the fuel, coolant, oil, or other fluid leaks.
Page 243: In Case Of Emergency
IN CASE OF EMERGENCY NOTE: HAZARD WARNING FLASHERS WARNING! With extended use, the Hazard Warning Flashers may wear down your battery. The Hazard Warning Flashers button is located in the ALWAYS obey traffic laws and pay attention to the lower center area of the instrument panel. road.
Page 244 IN CASE OF EMERGENCY SOS Call WARNING! WARNING! 1. Push the SOS Call button on the Rearview Mirror. • ALWAYS obey traffic laws and pay attention to the If anyone in the vehicle could be in danger (e.g., NOTE: fire or smoke is visible, dangerous road conditions road.
Page 245 IN CASE OF EMERGENCY SOS Call System Limitations NOTE: • The SOS Call system software and/or hardware are Vehicles sold in Mexico DO NOT have SOS Call system damaged during a crash Changes or modifications not expressly approved by the •...
Page 246: Jacking And Tire Changing - If Equipped
IN CASE OF EMERGENCY NOTE: JACKING AND TIRE CHANGING — PREPARATIONS FOR JACKING Passengers should not remain in the vehicle when the 1. Park the vehicle on a firm, level surface. Avoid ice or IF EQUIPPED vehicle is being lifted or raised. slippery areas.
Page 247: Jacking Instructions
IN CASE OF EMERGENCY 3. Turn the jack screw counterclockwise to remove the WARNING! jack from the storage area behind the tire. • Do not let any passenger sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 248 IN CASE OF EMERGENCY Detailed information about the inflatable spare tire, its use, and operation page 301. Jacking Locations Front Jack Location Extending The Wrench 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn while the wheel is still on the ground.
Page 249 IN CASE OF EMERGENCY 3. Place the wrench on the jack screw and turn clock- wise until the jack head is properly engaged in the described location. Do not raise the vehicle until you are sure the jack is securely engaged. 4.
Page 250: Road Tire Installation
IN CASE OF EMERGENCY 9. Lower the vehicle once the inflatable Spare has reached its pressure and the compressor-hose has been removed from the tire valve. 10. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage.
Page 251: Portable Air Compressor - If Equipped
IN CASE OF EMERGENCY 4. Uncoil the power plug and connect it to WARNING! the vehicles 12 Volt power outlet. To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered.
Page 252: Return Inflatable Spare Tire
IN CASE OF EMERGENCY TIRE SERVICE KIT — IF EQUIPPED WARNING! Use this QR code to access your digital • Do not lift or carry the Portable Air Compressor by experience. the hose. • Always stow the Portable Air Compressor only in Your vehicle may be equipped with a the provided place.
Page 253 IN CASE OF EMERGENCY Tire Service Kit Components And Operation Using The Power Button • • You can use the Tire Service Kit air pump to inflate bicycle tires. The kit also comes with two needles, Push and release the Power Button once located in the Accessory Storage Compartment (on to turn On the Tire Service Kit.
Page 254 IN CASE OF EMERGENCY NOTE: Setting Up To Use Tire Service Kit: WARNING! Sealant may leak out through the puncture in the tire. 1. Uncoil the Sealant Hose and then remove the cap • Take care not to allow the contents of Tire Service If the sealant (white fluid) does not flow within 0 –...
Page 255 IN CASE OF EMERGENCY If the tire does not inflate to at least 26 psi (1.8 bar) 3. Remove the cap from the valve stem, and then WARNING! within 15 minutes: screw the fitting at the end of the Sealant Hose onto the valve stem.
Page 256: Jump Starting - Gas Models
IN CASE OF EMERGENCY 3. Place the Tire Service Kit in its proper storage area 3. Remove the bottle cover. 5. Pull the bottle away from the Compressor. in the vehicle. 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer or tire service center.
Page 257: Preparations For Jump Start - Gas Models
IN CASE OF EMERGENCY NOTE: 4. If using another vehicle to jump start the battery, WARNING! park the vehicle within the jumper cable’s reach, set When using a portable battery booster pack, follow the • the parking brake and make sure the ignition is OFF. manufacturer’s operating instructions and precautions.
Page 258: Jump Starting - Hybrid Models
IN CASE OF EMERGENCY 4. Connect the opposite end of the negative (-) jumper If the vehicle's high voltage battery has also been dis- CAUTION! cable to the remote negative (-) post near the wind- charged, it will need to be recharged to a minimum shield cowl (exposed metallic/unpainted post of the operating State Of Charge (SOC) before the vehicle can The rear 12 Volt DC outlet is not controlled by the...
Page 259: Preparations For Jump Start - Hybrid Models
IN CASE OF EMERGENCY NOTE: When the vehicle is at the charging location, shift the PREPARATIONS FOR JUMP START — transmission back to PARK, apply the Electric Park The positive battery post may be covered with a protec- HYBRID MODELS Brake, and start the high voltage battery charging.
Page 260: Jump Starting Procedure - Hybrid Models
IN CASE OF EMERGENCY JUMP STARTING PROCEDURE — WARNING! CAUTION! HYBRID MODELS Do not connect the jumper cable to the negative (-) The rear 12 Volt DC outlet is not controlled by the post of the discharged battery. The resulting electrical vehicle’s ignition (the outlet provides power even WARNING! spark could cause the battery to explode and could...
Page 261: If Your Engine Overheats
IN CASE OF EMERGENCY WARNING! • A fire may result if fuel is pumped into a portable container that is inside of a vehicle. You could be burned. Always place fuel containers on the ground while filling. IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.
Page 262: Manual Park Release
IN CASE OF EMERGENCY • Turn off the Air Conditioner (A/C). The A/C system To move the vehicle in cases where the transmission adds heat to the engine cooling system and turning will not shift out of PARK (P) (such as a depleted bat- the A/C off can help remove this heat.
Page 263: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY • FREEING A STUCK VEHICLE Push the ESC OFF button to place the Electronic CAUTION! Stability Control (ESC) system in “Partial Off” mode, before rocking the vehicle page 196. Once the • If your vehicle becomes stuck in mud, sand or snow, it Racing the engine or spinning the wheels may lead vehicle has been freed, push the ESC OFF button can often be moved using a rocking motion.
Page 264 IN CASE OF EMERGENCY NOTE: NOTE: CAUTION! • • You must ensure that the Auto Park Brake feature is Ensure that the towing service tow hooks are prop- Recovery load should: disabled before towing this vehicle (if rear wheels erly seated and secured in the attachment points. •...
Page 265: All Wheel Drive (Awd) Models
IN CASE OF EMERGENCY ALL WHEEL DRIVE (AWD) MODELS FCA US LLC recommends towing your vehicle with all four wheels OFF the ground using a flatbed. CAUTION! • Towing this vehicle using any other method can cause severe transmission and/or transfer case damage.
Page 266: Servicing And Maintenance
SERVICING AND MAINTENANCE Once A Month Or Before A Long Trip: SCHEDULED SERVICING An authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If • Check engine oil level. a scheduled oil change is performed by someone other Your vehicle is equipped with an automatic oil change •...
Page 267 SERVICING AND MAINTENANCE Mileage Or Time Passed (Whichever Comes First) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints Inspect front suspension, boot seals, tie rod ends, and replace if necessary Inspect the brake linings, parking brake function Inspect front accessory drive tensioner, idler pulley, and replace if necessary Additional Maintenance Replace engine air cleaner filter Replace cabin air filter...
Page 268: Engine Compartment
SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L ENGINE 1 — Engine Coolant Pressure Cap 5 — Power Distribution Center (Fuses) 2 — Engine Oil Fill 6 — Windshield Washer Reservoir Cap 3 — Brake Fluid Reservoir Cap 7 — Engine Oil Dipstick 4 —...
Page 269: Engine Compartment - Hybrid Models
SERVICING AND MAINTENANCE ENGINE COMPARTMENT — HYBRID MODELS (IF EQUIPPED) 1 — Battery Coolant Reservoir 6 — Power Distribution Center (Fuses) 2 — Engine Coolant Pressure Reservoir 7 — Washer Fluid Reservoir Cap 3 — Engine Oil Fill 8 — Power Electronics Coolant Reservoir 4 —...
Page 270: Checking Oil Level
SERVICING AND MAINTENANCE CHECKING OIL LEVEL ADDING WASHER FLUID WARNING! To ensure proper engine lubrication, the engine oil must Commercially available windshield washer solvents be maintained at the correct level. Check the oil level at are flammable. They could ignite and burn you. Care regular intervals, such as every fuel stop.
Page 271: Pressure Washing
SERVICING AND MAINTENANCE NOTE: CAUTION! CAUTION! Intentional tampering with emissions control systems may void your warranty and could result in civil penal- • It is essential when replacing the cables on the Do not use chemical flushes in your engine oil as the ties being assessed against you.
Page 272: Engine Oil Filter
SERVICING AND MAINTENANCE ENGINE OIL FILTER ACCESSORY DRIVE BELT INSPECTION The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection WARNING! A full-flow type disposable oil filter should be used for •...
Page 273: Air Conditioner Maintenance
SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling — AIR CONDITIONER MAINTENANCE The cabin air filter is located in the fresh air inlet behind R–1234yf the glove compartment. Perform the following proce- For best possible performance, your air conditioner dure to replace the filter: should be checked and serviced by an authorized R–1234yf Air Conditioning Refrigerant is a Hydrofluo- 1.
Page 274: Body Lubrication
SERVICING AND MAINTENANCE 4. Open the glove compartment door as far as possible 9. Once the filter is replaced, reinstall the filter cover, to gain access to the cabin air filter compartment making sure the retaining tabs are fully secured into cover.
Page 275: Windshield Wiper Blades
SERVICING AND MAINTENANCE Front Wiper Blade Removal/Installation WINDSHIELD WIPER BLADES 2. To disengage the wiper blade from the wiper arm, flip up the release tab on the wiper blade and while Clean the rubber edges of the wiper blades and the holding the wiper arm with one hand, slide the wiper CAUTION! windshield periodically with a sponge or soft cloth and...
Page 276 SERVICING AND MAINTENANCE Rear Wiper Blade Removal/Installation 2. Lift the rear wiper arm fully off the glass. 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass.
Page 277: Exhaust System
SERVICING AND MAINTENANCE 3. Insert the wiper blade pivot pin into the opening on CAUTION! the end of the wiper arm. Grab the bottom end of the wiper arm with one hand, and press the wiper blade • The catalytic converter requires the use of flush with the wiper arm until it snaps into place.
Page 278: Cooling System
SERVICING AND MAINTENANCE Engine Coolant Checks Selection Of Coolant To minimize the possibility of catalytic converter damage: Check the engine coolant (antifreeze) protection every For further information page 313. • Do not interrupt the ignition when the transmission 12 months (before the onset of freezing weather, where NOTE: is in gear and the vehicle is in motion.
Page 279 SERVICING AND MAINTENANCE Adding Coolant Disposal Of Used Coolant • Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could Your vehicle has been built with an improved engine Used ethylene glycol-based coolant (antifreeze) is a lead to severe internal engine damage.
Page 280: Cooling System - Hybrid Models (If Equipped)
SERVICING AND MAINTENANCE If an examination of your engine compartment shows COOLING SYSTEM — HYBRID This vehicle is equipped with an electric cooling fan no evidence of radiator or hose leaks, the vehicle may mounted behind the radiator that starts automatically, MODELS (IF EQUIPPED) be safely driven.
Page 281 SERVICING AND MAINTENANCE Cooling System — Drain, Flush And Refill Selection Of Coolant Adding Coolant Your vehicle has been built with an improved coolant NOTE: NOTE: (OAT coolant conforming to MS.90032) that allows Some vehicles require special tools to add coolant prop- extended maintenance intervals.
Page 282 SERVICING AND MAINTENANCE Please note that it is the owner's responsibility to main- When additional coolant is needed to maintain the WARNING! tain the proper level of protection against freezing proper level, it should be added to the coolant bottle. according to the temperatures occurring in the area Do not overfill.
Page 283: Brake System
SERVICING AND MAINTENANCE Brake Master Cylinder • Make sure that the coolant expansion bottle over- WARNING! flow hoses are not kinked or obstructed. The fluid in the master cylinder should be checked • • Keep the front of the radiator clean. If your vehicle is Overfilling the brake fluid reservoir can result in when performing under hood services or immediately if equipped with air conditioning, keep the front of the...
Page 284: Fuses
SERVICING AND MAINTENANCE Fluid Level Check Selection Of Lubricant FUSES The fluid level is preset at the factory and does not It is important to use the proper transmission fluid to General Information require adjustment under normal operating conditions. ensure optimum transmission performance and life. Routine fluid level checks are not required;...
Page 285 SERVICING AND MAINTENANCE Underhood Fuses The fuses protect electrical systems against excessive current. The Power Distribution Center (PDC) is located in the When a device does not work, you must check the fuse engine compartment near the battery. This center con- element inside the blade fuse for a break/melt.
Page 286 SERVICING AND MAINTENANCE Power Distribution Center Location Cavity Cartridge Fuse Blade Fuse Description *If Equipped – – Not Populated – 25 Amp Clear Ignition Coil / Fuel Injector – – Not Populated...
Page 287 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped – 25 Amp Clear Amplifier / Active Noise Control * – – Not Populated – – Not Populated – 5 Amp Tan Battery Sensor (IBS) – 10 Amp Red ECM (S) * –...
Page 288 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped 30 Amp Pink – Power Liftgate Module * 25 Amp Clear – RR Door Module-LT * 25 Amp Clear – Sunroof * – – Not Populated 40 Amp Green –...
Page 289 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped Front and Rear HVAC Control Module / Occupant Classification Module (OCM) / – 10 Amp Red Electronic Steering Lock (ESL) / ESP / – – Not Populated Drive Train Control Mod / Power Transfer –...
Page 290 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped RR Entertainment / Media HUB / USB(S) / Rain Sensor / Sunroof / RR View Mirror/ – 10 Amp Red Overhead DVD Player / INT Monitoring Camera – 15 Amp Blue TCM (ZF) / E-Shifter / Cluster –...
Page 291: Bulb Replacement
SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped – 10 Amp Red Airbag – 15 Amp Blue Left HID Headlamp * 30 Amp Pink – Trailer Tow Elect Brake Module * Headlamp Level / RR Camera / Blindspot F100 –...
Page 292 SERVICING AND MAINTENANCE Exterior Bulbs — Halogen Exterior Bulbs Lamps Bulb Number Front Turn Signal Lamp WY21W / 7440NA Front Side Marker Lamp W3W / 2821 Rear Side Marker Lamp W3W / 2821 4. Install the front turn signal lamp socket assembly into the housing, and rotate the front turn signal Replacing Exterior Bulbs lamp socket clockwise to lock it in place.
Page 293: Tires
SERVICING AND MAINTENANCE NOTE: TIRES • P (Passenger) — Metric tire sizing is based on US design standards. P-Metric tires have the letter “P” TIRE SAFETY INFORMATION molded into the sidewall preceding the size designa- Tire safety information will cover aspects of the follow- tion.
Page 294 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 295 SERVICING AND MAINTENANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 296 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: NOTE: 1. Number of people that can be carried in the vehicle. The proper cold tire inflation pressure is listed on the 2. Total weight your vehicle can carry. driver’s side B-pillar or the rear edge of the driver's side 3.
Page 297 SERVICING AND MAINTENANCE Steps For Determining Correct Load (6) If your vehicle will be towing a Limit— trailer, load from your trailer will be transferred to your vehicle. Consult (1) Locate the statement “The com- this manual to determine how this bined weight of occupants and cargo reduces the available cargo and lug- should never exceed XXX kg or...
Page 298 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 299: Tires - General Information
SERVICING AND MAINTENANCE TIRES — GENERAL INFORMATION Both underinflation and overinflation affect the stability CAUTION! of the vehicle and can produce a feeling of sluggish Tire Pressure response or over responsiveness in the steering. After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.
Page 300 SERVICING AND MAINTENANCE Tire Pressures For High Speed Operation Tire Repair It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat If your tire becomes damaged, it may be repaired if it The manufacturer advocates driving at safe speeds and mode page 205.
Page 301 SERVICING AND MAINTENANCE It is recommended you contact an authorized tire WARNING! dealer or original equipment dealer with any questions you may have on tire specifications or capability. Failure Tires and the spare tire should be replaced after six to use equivalent replacement tires may adversely years, regardless of the remaining tread.
Page 302: Tire Types
SERVICING AND MAINTENANCE Snow Tires Spare Tire Matching Original Equipped TIRE TYPES Tire And Wheel — If Equipped Some areas of the country require the use of All Season Tires — If Equipped snow tires during the Winter. Snow tires can Your vehicle may be equipped with a spare tire and be identified by a mountain/snowflake sym- All season tires provide traction for all seasons (Spring,...
Page 303: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE WARNING! WARNING! WARNING! Compact and collapsible spares are for temporary Compact and collapsible spares are for temporary Limited use spares are for emergency use only. Instal- emergency use only. With these spares, do not drive emergency use only. With these spares, do not drive lation of this limited use spare tire affects vehicle more than 50 mph (80 km/h).
Page 304: Snow Traction Devices
SERVICING AND MAINTENANCE NOTE: SNOW TRACTION DEVICES CAUTION! If you intend parking or storing your vehicle for an Use of traction devices require sufficient tire-to-body extended period after cleaning the wheels with wheel Avoid products or automatic car washes that use acidic clearance.
Page 305 SERVICING AND MAINTENANCE Snow Traction Device (Maximum Pro- FWD Hybrid Axle Tire/Wheel Size jection Beyond Tire Profile Or Trim Level Equivalent) Touring L 235/65R17 Limited 235/60R18 Front 9 mm Cable/Chain Pinnacle 235/60R18 Snow Traction Device (Maximum Pro- Axle Tire/Wheel Size jection Beyond Tire Profile Or Trim Level Equivalent)
Page 306: Tire Rotation Recommendations
SERVICING AND MAINTENANCE TIRE ROTATION DEPARTMENT OF TRANSPORTATION cantly from the norm due to variations in driving habits, service practices, and RECOMMENDATIONS UNIFORM TIRE QUALITY GRADES differences in road characteristics and The tires on the front and rear of your vehicle operate climate.
Page 307: Temperature Grades
SERVICING AND MAINTENANCE STORING THE VEHICLE — HYBRID TEMPERATURE GRADES WARNING! MODELS (IF EQUIPPED) The Temperature grades are A (the The temperature grade for this tire is highest), B, and C, representing the established for a tire that is properly If the vehicle should remain stationary for more than a tire's resistance to the generation of inflated and not overloaded.
Page 308: Bodywork
SERVICING AND MAINTENANCE What Causes Corrosion? NOTE: PRESERVING THE BODYWORK The hybrid has a feature of periodic wake-up that Corrosion is the result of deterioration or removal of Washing occurs every 21 days. This feature charges the 12 Volt paint and protective coatings from your vehicle. battery from the high voltage battery.
Page 309: Interiors
SERVICING AND MAINTENANCE Special Care INTERIORS WARNING! • If you drive on salted or dusty roads or if you drive SEATS AND FABRIC PARTS A frayed or torn seat belt could rip apart in a collision near the ocean, hose off the undercarriage at least and leave you with no protection.
Page 310: Leather Surfaces
SERVICING AND MAINTENANCE Cleaning Plastic Instrument Cluster CAUTION! Lenses Do not use alcohol and alcohol-based and/or ketone- The lenses in front of the instruments in this vehicle are based cleaning products to clean leather seats, as molded in clear plastic. When cleaning the lenses, care damage to the seat may result.
Page 311: Technical Specifications
TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER (VIN) In the event power assist is lost for any reason (i.e., Inspect the wheel mounting surface prior to mounting repeated brake applications with the engine off) the the tire and remove any corrosion or loose particles. brakes will still function.
Page 312: Fuel Requirements
TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS REFORMULATED GASOLINE Many areas of the country require the use of cleaner While operating on gasoline with the required octane burning gasoline referred to as “reformulated gasoline”. number, hearing a light knocking sound from the Reformulated gasoline contains oxygenates and are engine is not a cause for concern.
Page 313: Do Not Use E-85 In Non-Flex Fuel Vehicles
TECHNICAL SPECIFICATIONS DO NOT USE E-85 IN NON-FLEX without MMT. Gasoline blended with MMT reduces FUEL SYSTEM CAUTIONS spark plug life and reduces emissions system perfor- FUEL VEHICLES mance in some vehicles. The manufacturer recom- CAUTION! mends that gasoline without MMT be used in your Non-Flex Fuel Vehicles (FFV) are compatible with gaso- vehicle.
Page 314: Fluid Capacities
TECHNICAL SPECIFICATIONS FLUID CAPACITIES Metric Fuel (Approximate) 3.6L Engine 19 gal 71 L Engine Oil With Filter 3.6L Engine 5 qt 4.7 L Cooling System* 3.6L Engine 15 qt 14.2 L * Includes heater and coolant reservoir filled to MAX level. FLUID CAPACITIES —...
Page 315: Engine Fluids And Lubricants
TECHNICAL SPECIFICATIONS ENGINE FLUIDS AND LUBRICANTS Component Fluid, Lubricant, or Genuine Part We recommend using Mopar® Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Engine Coolant Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032. We recommend using Mopar®...
Page 316: Chassis Fluids And Lubricants
TECHNICAL SPECIFICATIONS CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease cor- rosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (anti- freeze) or any “globally compatible”...
Page 317: Customer Assistance
Available 24 hours, 7 days a week. FOR YOUR VEHICLE FCA US LLC and its authorized dealers are vitally inter- Call 1-800-521-2779 or visit chrysler.rsahelp.com(USA) ested in your satisfaction. We want you to be happy with Call 1-800-363-4869 or visit fca.roadsideaid.com our products and services.
Page 318: Fca Us Llc Customer Center
HEARING OR SPEECH IMPAIRED FCA US LLC reserves the right to modify the terms or closest authorized Chrysler, Dodge, Jeep®, or Ram discontinue the Roadside Assistance Program at any dealer. If you choose to go to another dealer, you will be (TDD/TTY) time.
Page 319: Service Contract
CUSTOMER ASSISTANCE MOPAR® PARTS SERVICE CONTRACT We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer You may have purchased a service contract for a has also made a major investment in facilities, tools, Mopar®...
Page 320: In Canada
CUSTOMER ASSISTANCE To contact NHTSA, you may call the PUBLICATION ORDER FORMS Change Of Ownership Or Address Vehicle Safety Hotline toll free at To order the following manuals, you may use either the *If you have purchased this vehicle used or have 1-888-327-4236 (TTY: website or the phone numbers listed below.
Page 321 CUSTOMER ASSISTANCE Le présent appareil est conforme aux CNR d`Innova- tion, Science and Economic Development applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est sus- ceptible d'en compromettre le fonctionnement.
Page 322 INDEX Air Pressure AUX Cord ..... .80 Tires .....297 Auxiliary Electrical Outlet (Power Outlet) .
Page 323 INDEX Clean Air Gasoline ....310 Dimmer Switch Cleaning Headlight ....62 Camera .
Page 324 INDEX Coolant (Antifreeze) ....313 Flooded Engine Starting ....121 Gross Vehicle Weight Rating ... .161 Cooling .
Page 325 INDEX Indicator Lights Instrument Cluster ....62 Blue .....117 Intensity Control .
Page 326 INDEX Locks Mopar Parts ....317 Automatic Door ....30 MP3 Control .
Page 327 INDEX Rear Folding ....38 Reclining ....39 Radial Ply Tires .
Page 328 INDEX Steering .....134 High Speed ....298 Trailer Towing Guide .
Page 329 INDEX Warning Lights Red ..... .111 Yellow .....113 Warning Lights And Messages .
Page 331 This Owner’s Manual has been prepared to help you get acquainted with your new Chrysler brand vehicle and to provide a convenient reference source for common questions. Not all features shown in this manual may apply to your vehicle. For additional information, visit mopar.com/om (USA), owners.mopar.ca (Canada) or your local Chrysler dealer.
Page 332 CANADA owners.mopar.ca ©2023 FCA US LLC. All Rights Reserved. Tous droits réservés. Chrysler is a registered trademark of FCA US LLC or FCA Canada Inc., used under license. Chrysler est une marque First Edition déposée de FCA US LLC ou FCA Canada Inc., utilisée sous le permis. App Store is a registered trademark of Apple Inc. Google Play Store is a registered trademark of Google.

Chrysler PACIFICA 2024 Owner's Manual

Quick Links

Related Manuals for Chrysler PACIFICA 2024

Summary of Contents for Chrysler PACIFICA 2024