Page 1 2022 Chrysler Pacifica O W N E R ’ S M A N U A L...
Page 2 This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........................9 GETTING TO KNOW YOUR VEHICLE ................. 14 GETTING TO KNOW YOUR INSTRUMENT PANEL ............106 STARTING AND OPERATING ....................126 MULTIMEDIA ..........................179 SAFETY ............................213 IN CASE OF EMERGENCY ....................270 SERVICING AND MAINTENANCE ..................294 TECHNICAL SPECIFICATIONS ....................343 CUSTOMER ASSISTANCE .....................349 INDEX .............................
Page 4 INTRODUCTION SEATS ..............32 DOORS..............23 Manual Door Locks — If Equipped ....23 Manual Adjustment (Front Seats) — SYMBOLS KEY............10 Power Door Locks — If Equipped.....24 If Equipped ............32 VEHICLE MODIFICATIONS/ALTERATIONS..10 Keyless Enter ‘n Go™ — Passive Entry ...24 Manual Adjustment (Rear Seats)....33 SYMBOL GLOSSARY..........
Page 5 CLIMATE CONTROLS ..........69 MIRRORS ............... 56 EXTERIOR LIGHTS ..........63 Inside Rearview Mirror........56 Multifunction Lever ..........63 Automatic Climate Control Descriptions Illuminated Vanity Mirrors — If Equipped ..56 Headlight Switch ..........63 And Functions...........69 Outside Mirrors ..........57 Daytime Running Lights (DRLs) — Manual Climate Control Descriptions And Driver's Outside Automatic Dimming If Equipped............64...
Page 6 GETTING TO KNOW YOUR STARTING AND OPERATING PANORAMIC SUNROOF — IF EQUIPPED ..... 90 Opening And Closing The Sunroof....91 INSTRUMENT PANEL STARTING THE ENGINE........126 Opening And Closing The Power Normal Starting ..........126 INSTRUMENT CLUSTER ........106 Sunshade — If Equipped ........91 AutoPark ............
Page 7 RECREATIONAL TOWING (BEHIND STOP/START SYSTEM — IF EQUIPPED .....139 PARKSENSE ACTIVE PARK ASSIST SYSTEM — Autostop Mode ..........139 IF EQUIPPED ............157 MOTORHOME) .............176 Possible Reasons The Engine Does Not Enabling And Disabling The ParkSense Towing This Vehicle Behind Another Autostop............
Page 8 SAFETY IN CASE OF EMERGENCY Parental Controls (Using the Rear Screens) ............205 SAFETY FEATURES..........213 HAZARD WARNING FLASHERS ......270 Pairing The Remote (Using the Rear Anti-Lock Brake System (ABS) ..... 213 ASSIST AND SOS MIRROR — IF EQUIPPED ..270 Screens) ............
Page 9 SERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS TIRES ..............323 Tire Safety Information ......... 323 SCHEDULED SERVICING ........294 VEHICLE IDENTIFICATION NUMBER (VIN) ..343 Tires — General Information ......330 Maintenance Plan ......... 295 BRAKE SYSTEM ...........343 Tire Types............333 ENGINE COMPARTMENT ........298 WHEEL AND TIRE TORQUE Spare Tires —...
Page 10 CUSTOMER ASSISTANCE IF YOU NEED ASSISTANCE......... 349 WARRANTY INFORMATION........350 FCA US LLC Customer Center....... 349 MOPAR® PARTS ..........351 SUGGESTIONS FOR OBTAINING SERVICE FOR FCA Canada Inc. Customer Center....349 REPORTING SAFETY DEFECTS ......351 YOUR VEHICLE ............349 Mexico............349 In The 50 United States And Prepare For The Appointment ......
Page 11: Introduction
FCA US LLC aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. When it comes to service, remember that authorized dealers know your Chrysler vehicle best, have factory-trained technicians, genuine Mopar® parts, and care about your satisfaction.
Page 12: Symbols Key
SYMBOLS KEY VEHICLE MODIFICATIONS/ALTERATIONS These statements are against operating WARNING! WARNING! procedures that could result in a collision, bodily Any modifications or alterations to this vehicle could seriously affect its injury and/or death. roadworthiness and safety and may lead to a collision resulting in serious These statements are against procedures that injury or death.
Page 13 Red Warning Lights Red Warning Lights Door Open Warning Light Seat Belt Reminder Warning Light Ú page 117 Ú page 119 Electric Power Steering Fault Warning Light Transmission Temperature Warning Light Ú page 117 Ú page 119 Electronic Throttle Control (ETC) Warning Light Vehicle Security Warning Light Ú...
Page 14 Yellow Warning Lights Yellow Warning Lights Electronic Stability Control (ESC) Active Warning Light Service Stop/Start System Warning Light Ú page 119 Ú page 121 Service LaneSense Warning Light Tire Pressure Monitoring System (TPMS) Warning Light Ú page 120 Ú page 121 LaneSense Warning Light Yellow Indicator Lights Ú...
Page 15 White Indicator Lights Green Indicator Lights Adaptive Cruise Control (ACC) Ready Light Front Fog Indicator Light Ú page 123 Ú page 122 Cruise Control Ready Indicator Light KeySense Indicator Light Ú page 123 Ú page 122 LaneSense Indicator Light LaneSense Indicator Light Ú...
Page 16: Getting To Know Your Vehicle
GETTING TO KNOW YOUR VEHICLE KEYS NOTE: The key fob’s wireless signal may be blocked if  the key fob is located next to a mobile phone, laptop, or other electronic device. This may Your vehicle is equipped with a key fob which result in poor performance.
Page 17 GETTING TO KNOW YOUR VEHICLE In case the ignition switch does not change with Vehicles Equipped With Keyless Enter ‘n Go™ — Replacing The Battery In The Key Fob Passive Entry the push of a button, the key fob may have a low or The recommended replacement battery is one fully depleted battery.
Page 18 GETTING TO KNOW YOUR VEHICLE 1. Remove the emergency key by pushing the 5. Align the back cover into its original position operate the vehicle. Once a key fob is mechanical release button on the side of the and snap it back in place by pushing it against programmed to a vehicle, it cannot be key fob with your thumb and then pulling the the fob until it is seated all around.
Page 19: Sentry Key
GETTING TO KNOW YOUR VEHICLE KeySense Features — If Equipped KeySense Unique Splash Screen activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. At vehicle start-up, the KeySense splash screen This feature provides the vehicle owner with the should inform the driver that the vehicle will be The system uses a key fob, keyless push button ability to customize vehicle settings that can be...
Page 20: Ignition Switch
GETTING TO KNOW YOUR VEHICLE ON/RUN CAUTION! Driving position  The Sentry Key Immobilizer system is not All electrical devices are available (e.g. climate  compatible with some aftermarket Remote Start controls, etc.) systems. Use of these systems may result in START vehicle starting problems and loss of security protection.
Page 21: Remote Start - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! WARNING! The key fob may not be detected by the vehicle  When leaving the vehicle, always remove the Do not start or run an engine in a closed  Keyless Enter ‘n Go™ system if it is located next ...
Page 22: To Exit Remote Start Mode
GETTING TO KNOW YOUR VEHICLE NOTE: Battery at an acceptable charge level  EMOTE TART With Remote Start, the engine will only run for PANIC button not pushed   If applicable, refer to the “Hybrid Supplement” for 15 minutes. System not disabled from previous Remote ...
Page 23: Remote Start Front Defrost Activation - If Equipped
GETTING TO KNOW YOUR VEHICLE Automatic Temperature Control (ATC) — Remote Start mode. This includes the OFF button EMOTE TART RONT EFROST If Equipped on the climate controls, which will turn the system — I CTIVATION QUIPPED off. The climate controls will be automatically adjusted When Remote Start is active, and the outside to the optimal temperature and mode settings EMOTE...
Page 24: Vehicle Security System - If Equipped
GETTING TO KNOW YOUR VEHICLE VEHICLE SECURITY SYSTEM — IF EQUIPPED Push the lock button on the exterior Passive system. If someone enters the vehicle through  Entry door handle with a valid key fob avail- the liftgate and opens any door, the alarm will The Vehicle Security system monitors the vehicle able in the same exterior zone Ú...
Page 25: Security System Manual Override
GETTING TO KNOW YOUR VEHICLE ECURITY YSTEM ANUAL VERRIDE WARNING! The Vehicle Security system will not arm if you lock Never use the PARK position as a substitute  the doors using the manual door lock. for the parking brake. Always apply the parking brake fully when parked to guard DOORS against vehicle movement and possible injury...
Page 26: Power Door Locks - If Equipped
GETTING TO KNOW YOUR VEHICLE — I ‘ ™ — If the vehicle is unlocked by Passive Entry and OWER OCKS QUIPPED EYLESS NTER  no door is opened within 60 seconds, the ASSIVE NTRY A power door lock switch is on each front door trim vehicle will relock and will arm the Vehicle Secu- panel.
Page 27 GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: The vehicle will only unlock the doors when a valid Either the driver door only or all doors will unlock  Passive Entry key fob is detected inside the when you grab hold of the front driver’s door vehicle, and no valid key fob is detected outside handle, depending on the selected setting in the the vehicle.
Page 28: Automatic Unlock Doors On Exit - If Equipped
GETTING TO KNOW YOUR VEHICLE — NOTE: UTOMATIC NLOCK OORS After pushing the door handle lock button, you  QUIPPED must wait two seconds before you can lock or The Unlock Doors Automatically On Exit feature unlock the doors, using either Passive Entry unlocks all of the vehicle doors when any door is door handle.
Page 29: Power Sliding Side Door - If Equipped
GETTING TO KNOW YOUR VEHICLE Always make sure that the sliding door is fully latched anytime the vehicle is in motion. NOTE: The left side sliding door cannot be opened while the fuel door is open. — OWER LIDING QUIPPED The power sliding door may be power opened or closed in several ways: Side Door Handle And Lock Functions...
Page 30: Hands-Free Sliding Doors - If Equipped
GETTING TO KNOW YOUR VEHICLE when the handles are manual. When the LED is lit, WARNING! pushing the power sliding door power off button will return the handles to power operation. Personal injury or cargo damage may occur if  caught in the path of the sliding door.
Page 31: Child Protection Door Lock System - Rear Doors
GETTING TO KNOW YOUR VEHICLE If anything obstructs the power sliding side door The power sliding door will operate from the   while it is closing or opening, the door will auto- switch located just inside the sliding door, matically reverse to the closed or open position regardless of the Child Protection Door Lock and an audible tone will sound, provided it...
Page 32: Steering Wheel
GETTING TO KNOW YOUR VEHICLE NOTE: To unlock the steering column, push the lever steering wheel can shut off early or may not turn on downward (toward the floor). To tilt the steering when the steering wheel is already warm. After disengaging (or engaging) the Child column, move the steering wheel upward or Protection Door Lock, always test the inside door...
Page 33: Driver Memory Settings - If Equipped
GETTING TO KNOW YOUR VEHICLE DRIVER MEMORY SETTINGS — IF EQUIPPED 3. Push the set (S) button on the memory switch, and then push the desired memory button (1 This feature allows the driver to save up to two or 2) within five seconds. The instrument different memory profiles for easy recall through a cluster display will show which memory memory switch.
Page 34: Memory Position Recall
GETTING TO KNOW YOUR VEHICLE 4. Push and release button (1) or (2) accordingly. A recall can be cancelled by pushing any of the ANUAL DJUSTMENT “Memory Profile Set” (1 or 2) will display in the memory buttons on the driver's door during a recall ) —...
Page 35: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE Manual Front Adjuster WARNING! WARNING! Both front seats are adjustable forward or Adjusting a seat while driving may be Do not ride with the seatback reclined so that  rearward. The manual seat adjustment handle is dangerous.
Page 36 GETTING TO KNOW YOUR VEHICLE Manual Forward/Rearward Adjustment — seatback to its normal position. Using body WARNING! pressure, lean forward and rearward on the seat to Quad Seats (If Equipped) be sure the seatback has latched. Adjusting a seat while driving may be ...
Page 37 GETTING TO KNOW YOUR VEHICLE 4. Once the latches are released, tilt the entire seat toward the front of the vehicle. The seat can now be removed through either sliding side door, or through the liftgate. Recline Lever Folded Position The bench seat does not stow in the floor, but is 3.
Page 38 GETTING TO KNOW YOUR VEHICLE NOTE: Reinstalling The Bench Seat Seat can be removed easier with one outboard 1. To reinstall the bench seat, align the seats seat stowed in the load floor. front attachments into the detent positions To reinstall the seat, align the seat into the detent on the floor.
Page 39 GETTING TO KNOW YOUR VEHICLE Fold-Flat — Quad Seats To fold the seat, lift the recliner lever to the full upward position and push the seatback forward until it rests on the seat cushion. Stow ‘n Go Seating Head Restraint Lift Easy Tilt Seat Lever (If Equipped) Easy Entry Easy Tilt Seat —...
Page 40 GETTING TO KNOW YOUR VEHICLE 3. Push on seatback to slide seat forward to Exit For Third Row Passengers — Stow ‘n Go Seats WARNING! access the third row. Only Do not use this feature with a child in seat. Seri- If the second row is equipped with Stow ‘n Go, third ous injury or death may occur.
Page 41 GETTING TO KNOW YOUR VEHICLE Second Row Removable Quad Seat 6. The seat assembly can now be removed from the vehicle. Grab the front seatback edge The second row quad seats, not equipped with the located near the head restraint and the grab Stow ‘n Go feature, are removable for added cargo the bar on the rear side of the seat cushion for space.
Page 42 GETTING TO KNOW YOUR VEHICLE Reinstalling Seat 2. Tilt seat rearward to lock the seat back into its original position. 1. To reinstall the seat: With the seat tilted forward, align the seat’s front attachments NOTE: into the detent positions on the floor. Push downward to ensure the rear latches are in the locked position.
Page 43 GETTING TO KNOW YOUR VEHICLE 2. Pulling strap “2” releases the seatback to Stow 'n Go Seating return to its full upright position. On vehicles equipped with Stow 'n Go seating, the second and third row seats can be folded into the floor for convenient storage.
Page 44 GETTING TO KNOW YOUR VEHICLE A one-touch Auto Advance ‘n Return button is 1. Push and release the Auto Advance ‘n Return If calibration of the front seat is lost, the seat will  located on the B-pillar trim panel, just in front of button.
Page 45 GETTING TO KNOW YOUR VEHICLE 1. To access the storage area, remove the floor 5. Fold the armrest upward and stow the seat by mat (if equipped) and place the lock rod in the grabbing the strap on the lower part of the locked position.
Page 46 GETTING TO KNOW YOUR VEHICLE TO UNSTOW SECOND ROW SEATS 7. Close the floor by pulling the floor panel 9. Readjust the front seat as needed, and backwards by the bottom corner edge of the replace the floor mat (if equipped). For Manual Seats: To unstow the seat from the panel.
Page 47 GETTING TO KNOW YOUR VEHICLE 2. Pull the latch located near the second row seat 4. Pull the strap located on the seat and pull the to open the floor panel. seat out of the storage area. Push the seat rearward making sure that it locks into the floor.
Page 48: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! In a collision, you or others in your vehicle Do not ride with the seatback reclined so that   could be injured if seats are not properly the shoulder belt is no longer resting against latched to their floor attachments.
Page 49 GETTING TO KNOW YOUR VEHICLE Tilting The Seat Up Or Down Easy Entry/Exit Seat — If Equipped CAUTION! The angle of the seat cushion can be adjusted in This feature provides automatic driver seat Do not place any article under a power seat or two directions.
Page 50: Power Adjustment (Rear Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE When enabled within Uconnect Settings, Easy Reclining The Seatback WARNING! Entry and Easy Exit positions are stored in each The angle of the seatback can be adjusted forward memory setting profile (if equipped) Ú page 31. Do not place the seat belt webbing behind the ...
Page 51 GETTING TO KNOW YOUR VEHICLE Third Row Power Stow ‘n Go Seat — Left and right third row seats can be folded To move the selected seat(s) to the stow position, push and release the “Stow” button. The seat will individually or together.
Page 52: Heated Seats
GETTING TO KNOW YOUR VEHICLE NOTE: Rear Heated Seats — If Equipped 3. To abort seat operation while seat is in motion, push a different seat position selector switch Once a heat setting is selected, heat will be felt  On some models, the second row seats are to stop the seat.
Page 53: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: LASTIC ROCERY ETAINER Once a heat setting is selected, heat will be felt The engine must be running for the ventilated OOKS within two to five minutes. seats to operate. Retainer hooks which will hold plastic grocery bag When the HI-level setting is selected, the heater For information on use with the Remote Start handles are built into the seatbacks of the second...
Page 54 GETTING TO KNOW YOUR VEHICLE Head Restraints — Front Seats The front driver and passenger seats are equipped with four-way head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push downward.
Page 55 GETTING TO KNOW YOUR VEHICLE Head Restraints — Second Row Quad Head Restraints — Second Row Bench To remove the head restraint, raise it as far as it can go. Then, push the release button and the Seats The second row bench seat is equipped with adjustment button at the base of each post while adjustable head restraints.
Page 56 GETTING TO KNOW YOUR VEHICLE Head Restraints — Third Row NOTE: POWER FOLDING THIRD ROW HEAD To remove the center head restraint, raise it as far RESTRAINTS — IF EQUIPPED The outboard head restraints can be manually as it can go. Then, push the release button and the folded forward for improved rearward visibility.
Page 57: Uconnect Voice Recognition - If Equipped
GETTING TO KNOW YOUR VEHICLE UCONNECT VOICE RECOGNITION — TARTED IF EQUIPPED VR button is used to activate /deactivate your Voice Recognition system. NTRODUCING OICE ECOGNITION Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition (VR) with Reduce background noise. Wind noise and ...
Page 58: Mirrors
GETTING TO KNOW YOUR VEHICLE MIRRORS Automatic Dimming Mirror — If Equipped CAUTION! This mirror automatically adjusts for headlight To avoid damage to the mirror during cleaning, NSIDE EARVIEW IRROR glare from vehicles behind you. You can turn the never spray any cleaning solution directly onto feature on or off by pushing the button at the base Manual Mirror —...
Page 59: Outside Mirrors
GETTING TO KNOW YOUR VEHICLE UTSIDE IRRORS ONVERSATION IRROR The outside mirror(s) can be adjusted to the center Located in the overhead console there is a of the adjacent lane of traffic to achieve the conversation mirror to view all the passengers in optimal view.
Page 60: Outside Mirrors Folding Feature
GETTING TO KNOW YOUR VEHICLE NOTE: If the mirrors are in the folded position, and vehicle UTSIDE IRRORS OLDING EATURE speed is equal or greater than 10 mph (16 km/h), The Tilt Side Mirrors In Reverse feature can be All outside mirrors are hinged and may be moved they will automatically unfold.
Page 61: Universal Garage Door Opener (Homelink®)
GETTING TO KNOW YOUR VEHICLE UNIVERSAL GARAGE DOOR OPENER ® To operate HomeLink®, push and release any RASING  of the programmed HomeLink® buttons. These HANNELS (HOMELINK®) buttons will activate the devices they are programmed to with each press of the corre- To erase the channels, follow this procedure: sponding HomeLink®...
Page 62: Programming Homelink® To A Garage Door Opener
GETTING TO KNOW YOUR VEHICLE not be immediately visible when looking at the garage door opener transmitter button you are operates. If the garage door opener motor device. The name and color of the button may vary trying to replicate. does not operate, repeat the final steps for the slightly by manufacturer.
Page 63: Programming Homelink® To A Miscellaneous Device
GETTING TO KNOW YOUR VEHICLE ® T 1. Place the ignition in the ON/RUN position, 1. Place the ignition in the ON/RUN position. ROGRAMMING without starting the engine. NOTE: ISCELLANEOUS EVICE 2. Push and hold the desired HomeLink® button For vehicles equipped with Keyless Enter ‘n Go™, The procedure on how to program HomeLink®...
Page 64: Security
GETTING TO KNOW YOUR VEHICLE NOTE: If you have any problems, or require assistance, ECURITY please call toll-free 1-800-355-3515 or, on the If the indicator light stays on constantly,  It is advised to erase all channels before you sell or Internet at HomeLink.com for information or programming is complete and the garage turn in your vehicle.
Page 65: Exterior Lights
GETTING TO KNOW YOUR VEHICLE EXTERIOR LIGHTS ULTIFUNCTION EVER The multifunction lever is located on the left side of the steering column. The multifunction lever controls the turn signals, headlight high/low beams, and flash-to-pass functions. Headlight Switch Headlight Switch (Vehicles Sold In Canada Only) 1 —...
Page 66: Daytime Running Lights (Drls) - If Equipped
GETTING TO KNOW YOUR VEHICLE NOTE: 3. Push the multifunction lever away from you to WITCH switch the headlights to the high beam For vehicles sold in Canada, rotate the headlight Push the multifunction lever toward the instrument position. Refer to “Multifunction Lever” in this switch clockwise from the parking light and panel to switch the headlights to high beams.
Page 67: Automatic Headlights - If Equipped
GETTING TO KNOW YOUR VEHICLE — I — I — I UTOMATIC EADLIGHTS QUIPPED EADLIGHT ELAY QUIPPED RONT IGHTS QUIPPED This system automatically turns your headlights on This feature provides the safety of headlight To activate the front fog lights, turn on the parking or off based on ambient light levels.
Page 68: Turn Signals
GETTING TO KNOW YOUR VEHICLE NOTE: To operate the courtesy lights, push either the IGNALS driver or passenger light switch. Battery saver mode is canceled if the ignition is Move the multifunction lever up or down to placed in the ON position. NOTE: activate the turn signals.
Page 69: Windshield Wiper And Washers
GETTING TO KNOW YOUR VEHICLE Dimmer Control INDSHIELD IPER PERATION The dimmer controls are part of the headlight The wipers and washers are operated by a switch switch, and are located on the driver’s side of the within the wiper lever. Rotate the switch at the end instrument panel.
Page 70: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE while the wipers are in the off position, the wipers The sensitivity of the system is adjustable from the CAUTION! will operate several cycles, then turn off. windshield wiper lever. Wiper sensitivity position 1 is the least sensitive, and wiper sensitivity position Always remove any buildup of snow that WARNING! 4 is the most sensitive.
Page 71: Rear Wiper And Washer
GETTING TO KNOW YOUR VEHICLE Neutral Wipe Inhibit — The Rain Sensing feature Rear Window Washer Operation  will not operate when the ignition is ON, when Pushing the windshield wiper lever the transmission gear selector is in the forward activates the rear window NEUTRAL position and the vehicle speed is less washer.
Page 72 GETTING TO KNOW YOUR VEHICLE A/C Button Front Defrost Button out) if conditions exist that could create fogging on the inside of the windshield. The A/C can be Press and release the button on the Press and release the Front Defrost deselected manually without disturbing the mode touchscreen, or push the button on the button on the touchscreen, or push the...
Page 73 GETTING TO KNOW YOUR VEHICLE button on the touchscreen for cooler temperature Faceplate: The blower speed increases as you  CAUTION! settings. turn the blower control knob clockwise from the lowest blower setting. The blower speed Failure to follow these cautions can cause NOTE: decreases as you turn the blower control knob damage to the heating elements:...
Page 74 GETTING TO KNOW YOUR VEHICLE Bi-Level Mode Controlling The Rear Climate Controls REAR CLIMATE CONTROL BUTTON From The Front ATC Panel—If Equipped Air comes from the instrument panel Press and release the Rear Climate outlets and floor outlets. A slight amount button to access the rear climate The Three-Zone Automatic Temperature Control of air is directed through the defrost and...
Page 75 GETTING TO KNOW YOUR VEHICLE REAR TEMPERATURE CONTROL BLOWER CONTROL FLOOR MODE These buttons provide the front occupants with the Blower Control is used to regulate the Press this button on the touchscreen to ability to control the rear temperature. amount of air forced through the Climate change the air distribution mode to Floor Control system.
Page 76 GETTING TO KNOW YOUR VEHICLE AUTO BUTTON REAR MODE CONTROL The AUTO button automatically controls Push this button on the Rear Climate the interior cabin temperature by Controls to change the air distribution adjusting distribution and amount of mode for the rear passengers. airflow.
Page 77: Manual Climate Control Descriptions And Functions
GETTING TO KNOW YOUR VEHICLE REAR CLIMATE CONTROL/BLOWER OFF NOTE: such as smoke, odors, dust, or high humidity are The MAX A/C setting is only available on the touch- present. Recirculation can be used in all modes To manually set the rear blower controls except for Defrost.
Page 78 GETTING TO KNOW YOUR VEHICLE Front Temperature Control into manual mode. If the Front Defrost mode is temperatures only. In order to SYNC rear turned off the climate system will return the temperature to driver temperature, the These buttons provide the driver and passenger previous setting.
Page 79 GETTING TO KNOW YOUR VEHICLE Mode Control Floor Mode Press the “Front Climate” button on the touch-  screen to return to the front climate controls. The airflow distribution mode can be Air comes from the floor outlets. A slight adjusted so air comes from the amount of air is directed through the REAR CLIMATE CONTROL BUTTON...
Page 80 GETTING TO KNOW YOUR VEHICLE NOTE: PANEL MODE REAR PASSENGER CLIMATE CONTROL OFF When the SYNC feature is active, the passenger’s BUTTON Press this button on the touchscreen to temperature moves up and down with the driver’s change the air distribution mode to Panel Press and release this button to turn the temperature.
Page 81: Automatic Temperature Control (Atc)
GETTING TO KNOW YOUR VEHICLE vehicle. The larger of the two icons increases REAR CLIMATE CONTROL/BLOWER OFF CAUTION! blower speed, whereas the smaller of the two icons To manually set the rear blower controls decreases the blower speed. Interior air enters the Rear Automatic Tempera- to off, press the Rear Climate Control/ ture Control system through an intake grille, Blower Off button.
Page 82: Climate Voice Commands
GETTING TO KNOW YOUR VEHICLE Window Fogging The temperature can be displayed in U.S. or  PERATING Metric units by selecting the U.S./Metric Vehicle windows tend to fog on the inside in mild, Refer to the chart at the end of this section for customer-programmable feature within the rainy, and/or humid weather.
Page 83: Interior Storage And Equipment
GETTING TO KNOW YOUR VEHICLE INTERIOR STORAGE AND EQUIPMENT Operating Tips Chart WARNING! WEATHER CONTROL SETTINGS If containers of hot liquid are placed in the bottle TORAGE holder, they can spill when the door is closed, Set the mode control to Glove Compartment burning the occupants.
Page 84 GETTING TO KNOW YOUR VEHICLE Instrument Panel Drawer 1. To access the storage bins with front seats in the rearward position, place the lock rod in There is a storage drawer located in the lower the unlocked position so the load floor can center of the instrument panel.
Page 85 GETTING TO KNOW YOUR VEHICLE 2. Pull the latch located near the second row seat CAUTION! WARNING! to open the floor panel. The storage bin cover must lay flat and be Do not drive the vehicle with the storage bin ...
Page 86: Sun Screens - If Equipped
GETTING TO KNOW YOUR VEHICLE SEAT STORAGE BIN COVER EMERGENCY Gently pull up on the tab to raise the sun screen. bility and allow for files/media to be stored, if Continue pulling the sun screen until the tab is equipped with Uconnect Theater. RELEASE LEVER near the top of the window.
Page 87 GETTING TO KNOW YOUR VEHICLE There are multiple USB “Charge Only” ports in this vehicle. In the center console  On the instrument panel  On the back of the front row seats in the  Uconnect Theater Media Hubs (if equipped) On the back of the front row seats ...
Page 88: Power Outlets
GETTING TO KNOW YOUR VEHICLE Plugging in a phone or another USB device may CAUTION! cause the connection to a previous device to be lost. Power outlets are designed for accessory plugs only. Do not insert any other object in the power NOTE: outlets as this will damage the outlet and blow Charge unsupported devices with the Charge Only...
Page 89: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE — I NOTE: OWER NVERTER QUIPPED WARNING! The instrument panel power outlet can be changed There is a 115 Volt, 150 Watt Power Inverter outlet to “battery” (powered at all times) by switching the Do not touch with wet hands. ...
Page 90: Wireless Charging Pad - If Equipped
GETTING TO KNOW YOUR VEHICLE Inverter, it resets. To avoid overloading the circuit, Your vehicle may be equipped with a 15W 3A Qi CAUTION! check the power ratings on electrical devices prior wireless charging pad located inside of the storage to using the Power Inverter.
Page 91: Automatic Window Features
GETTING TO KNOW YOUR VEHICLE The driver may lock out the rear power windows by Sliding Side Door Power Window Control — UTOMATIC INDOW EATURES pushing the bar control just below the power If Equipped Auto-Down Feature window controls. Second row passengers may open and close the The driver and front passenger door power window sliding door window by a single control on the door switches have an Auto-Down feature.
Page 92: Reset Auto-Up
GETTING TO KNOW YOUR VEHICLE together to minimize the buffeting. If the buffeting WARNING! WARNING! occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any There is no anti-pinch protection when the Never leave children unattended in a vehicle, ...
Page 93: Opening And Closing The Sunroof
GETTING TO KNOW YOUR VEHICLE button again will automatically close both the PENING LOSING UNROOF PENING LOSING OWER sunroof and shade completely. — I UNSHADE QUIPPED Express Open/Close Manual Open/Close Push the open switch and release it within one The sunshade has two programmed open Push and hold the sunshade open switch and the second.
Page 94: Venting Sunroof
GETTING TO KNOW YOUR VEHICLE HOOD ENTING UNROOF Push and release the "Vent" button within one PENING second and the sunroof will open to the vent position. This is called “Express Vent”, and it will If applicable, refer to the “Hybrid Supplement” for occur regardless of sunroof position.
Page 95: Closing
GETTING TO KNOW YOUR VEHICLE LIFTGATE LOSING If applicable, refer to the “Hybrid Supplement” for NLOCK IFTGATE additional information. The liftgate may be released in several ways: 1. Hold up the hood with one hand and with the other hand remove the support rod from its Key fob ...
Page 96: Power Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE Using the above ways to open or close the liftgate: The key fob and the overhead console button will WARNING! operate the liftgate when the liftgate is locked. The When the liftgate is fully closed, the liftgate will ...
Page 97: Hands-Free Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE — I To Close The Liftgate ANDS IFTGATE QUIPPED The liftgate can also be closed using the Rear Interior Power Liftgate button (if equipped), located in the upper left trim in the liftgate opening. Hands-Free Liftgate Trailer Tow Activation Zones When a valid kicking motion is completed, the Hands-Free Liftgate Activation Zone liftgate will chime, the hazard lights will flash and...
Page 98: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE NOTE: ARGO EATURES WARNING! The Hands-Free Liftgate will only operate when  Cargo Area Storage Driving with the liftgate open can allow the transmission is in PARK.  poisonous exhaust gases into your vehicle. When the third row seats are not in the stowed If anything obstructs the Hands-Free Liftgate ...
Page 99 GETTING TO KNOW YOUR VEHICLE Stow ‘n Vac Integrated Vacuum — WARNING! WARNING! If Equipped Do not leave the key fob in or near the vehicle, Do not vacuum any flammable   Your vehicle may be equipped with an integrated or in a location accessible to children, and do liquids, such as gasoline, or use around vacuum system.
Page 100 GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! WARNING! The vacuum will not operate when the ignition is in the OFF position, or in the ON/RUN position with Carbon monoxide (CO) in exhaust gases can Do not vacuum hard or sharp objects such as ...
Page 101 GETTING TO KNOW YOUR VEHICLE 3. Install desired attachment if needed. 4. Push the vacuum on/off button located WARNING! under the vacuum nozzle storage location. Use For in vehicle use ONLY. To reduce the risk of vacuum as needed. fire, serious injury or death: NOTE: Do not use vacuum while vehicle is in ...
Page 102 GETTING TO KNOW YOUR VEHICLE 5. When finished, push power button to turn holes or other damage and needs to be WARNING! vacuum off and store vacuum hose and any replaced, please contact an authorized dealer. attachments. Use only as described in this manual. Use only ...
Page 103 GETTING TO KNOW YOUR VEHICLE To Remove Vacuum Hose For Cleaning 1. Open the access panel. Debris Bin Release Knob Vacuum Hose Release Lever 4. Remove the filter and dump the debris in a 3. Return to vacuum nozzle storage location trash can.
Page 104: Stow 'N Place Roof Rack - If Equipped
GETTING TO KNOW YOUR VEHICLE STOW ‘N PLACE ROOF RACK — IF EQUIPPED NOTE: The Stow ‘N Place roof rack does not increase the total load carrying capacity of the vehicle. Be sure The thumb screws cannot be fully removed. The crossbars and side rails are designed to carry the total load of cargo inside the vehicle plus that weight on vehicles equipped with a luggage rack.
Page 105: Stowing The Crossbars
GETTING TO KNOW YOUR VEHICLE 2. Bend the crossbar supports at each end, 4. Once the crossbar is in place, tighten both TOWING ROSSBARS taking care to keep hand clear of pivoting joint. thumb screws completely. 1. Starting with one crossbar, completely loosen Slide the thumb screw down.
Page 106 GETTING TO KNOW YOUR VEHICLE NOTE: 3. Then, position the crossbar along the correct 5. Once the driver’s side crossbar is in place, side rail. Make sure the letters on the crossbar tighten the thumb screws completely. To help control wind noise, stow the crossbars in ...
Page 107 GETTING TO KNOW YOUR VEHICLE CAUTION! To avoid damage to the roof rack and vehicle,  do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately.
Page 108: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 109 GETTING TO KNOW YOUR INSTRUMENT PANEL...
Page 110: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: NSTRUMENT LUSTER ESCRIPTIONS WARNING! The hard telltales will illuminate for a bulb check 1. Tachometer when the ignition is first cycled. Driving with a hot engine cooling system could Indicates the engine speed in revolutions damage your vehicle.
Page 111: Instrument Cluster Display Location And Controls
GETTING TO KNOW YOUR INSTRUMENT PANEL Right Arrow Button NSTRUMENT LUSTER ISPLAY  Push and release the right arrow button to OCATION ONTROLS access the information screens or submenu The vehicle’s instrument cluster is equipped with screens of a main menu item. an instrument cluster display (base or premium Down Arrow Button ...
Page 112: Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Life Reset Secondary Method For Oil Life Reset Procedure ESET 1. Without pressing the brake pedal, push the 1. Without pushing the brake pedal, place the Your vehicle is equipped with an engine oil ...
Page 113: Keysense Cluster Messages - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL — I ENSE LUSTER ESSAGES QUIPPED When the KeySense key is in use there will be: Continuous, dedicated telltale  Unique Display Splash Screen  With KeySense in use there will be multiple associated messages shown in the following table: Setting Instrument Cluster Display Message None –...
Page 114 GETTING TO KNOW YOUR INSTRUMENT PANEL Speedometer Driver Assist — If Equipped Transmission Temp Displays the actual transmission temperature. Push and release the up or down arrow Push and release the up or down arrow button until Speedometer is highlighted in the button until the Driver Assist display icon is Oil Temp instrument cluster display.
Page 115 GETTING TO KNOW YOUR INSTRUMENT PANEL Trip Info NOTE: Premium Instrument Cluster Display Screen The pop-up messages indicate the status of the Push and release the up or down arrow Setup Options: system and/or the conditions that need to be met. button until the Trip Menu item is highlighted in the Messages remain in the stored stack until Upper Center...
Page 116 GETTING TO KNOW YOUR INSTRUMENT PANEL Speed Warning — If Equipped Show  Base Instrument Cluster Display Screen Hide (Odometer will still appear when door Push and release the up or down arrow  Setup Options: is open) button until Speed Warning is highlighted in the Upper Right instrument cluster display.
Page 117: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: 150W, USB ports) during certain driving condi- ATTERY AVER ATTERY AVER tions (city driving, towing, frequent stopping). — E The charging system is independent from load  ESSAGE LECTRICAL reduction. The charging system performs a diag- Installing options like additional lights, upfitter ...
Page 118: Trip Computer
GETTING TO KNOW YOUR INSTRUMENT PANEL Check HVAC settings (blower, temperature) Shows the Average MPG for Trip A since the last information in this chapter in the event of a failure   reset. indication. All active telltales will display first if Check the audio settings (volume) ...
Page 119 GETTING TO KNOW YOUR INSTRUMENT PANEL Brake Warning Light NOTE: The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN The light may flash momentarily during sharp This warning light monitors various brake position.
Page 120 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Throttle Control (ETC) Warning Engine Coolant Temperature Warning Liftgate Open Warning Light Light Light This warning light will illuminate when the liftgate is open. This warning light will illuminate to This warning light warns of an indicate a problem with the ETC system.
Page 121: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Seat Belt Reminder Warning Light Anti-Lock Brake System (ABS) Warning CAUTION! Light This warning light indicates when the Continuous driving with the Transmission Tem- driver or passenger seat belt is This warning light monitors the ABS. The perature Warning Light illuminated will eventu- unbuckled.
Page 122 GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Warning Light — If Equipped vehicle has been driven several miles (kilometers) position before engine start. If the bulb does not at speeds greater than 30 mph (48 km/h), see an come on when turning the ignition switch from OFF The LaneSense Warning Light will be authorized dealer as soon as possible to have the to ON/RUN, have the condition checked promptly.
Page 123 GETTING TO KNOW YOUR INSTRUMENT PANEL Tire Pressure Monitoring System (TPMS) should determine the proper tire inflation pressure CAUTION! for those tires. Warning Light Prolonged driving with the Malfunction Indicator As an added safety feature, your vehicle has been The warning light switches on and a Light (MIL) on could cause damage to the vehi- equipped with a TPMS that illuminates a low tire message is displayed to indicate that the...
Page 124: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Cruise Control Set Indicator Light — system may not be able to detect or signal low tire ELLOW NDICATOR IGHTS pressure as intended. TPMS malfunctions may If Equipped Forward Collision Warning (FCW) OFF occur for a variety of reasons, including the This indicator light will illuminate when Indicator Light —...
Page 125: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL Parking/Headlights On Indicator Light Set Speed Display HITE NDICATOR IGHTS This indicator light will illuminate when The Set Speed Display indicator light Adaptive Cruise Control (ACC) Ready the parking lights or headlights are indicates the set speed for the Cruise Light —...
Page 126: Onboard Diagnostic System - Obd Ii
GETTING TO KNOW YOUR INSTRUMENT PANEL ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! WARNING! Your vehicle is equipped with a sophisticated Prolonged driving with the MIL on could cause ONLY an authorized service technician should   Onboard Diagnostic system called OBD II. This further damage to the emission control connect equipment to the OBD II connection system monitors the performance of the...
Page 127: Emissions Inspection And Maintenance
GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND 2. As soon as you cycle the ignition switch to the If your OBD II system is not ready, you should see ON position, you will see the Malfunction an authorized dealer or repair facility. If your MAINTENANCE PROGRAMS Indicator Light (MIL) symbol come on as part of vehicle was recently serviced or had a battery...
Page 128: Starting And Operating
STARTING AND OPERATING STARTING THE ENGINE ENGINE START/STOP Button Functions — With WARNING! Driver’s Foot OFF The Brake Pedal (In PARK Or Before starting your vehicle, adjust your seat, NEUTRAL Position) Do not leave children or animals inside parked  adjust both inside and outside mirrors, and fasten vehicles in hot weather.
Page 129: Autopark
STARTING AND OPERATING ALWAYS DO A VISUAL CHECK that your vehicle is in CAUTION! PARK by looking for the “P” in the instrument AutoPark is a supplemental feature to assist in cluster display and on the gear selector. As an Engine will remain running.
Page 130 STARTING AND OPERATING WARNING! WARNING! WARNING! Never use the PARK position as a substitute It is dangerous to shift out of PARK or Never leave children alone in a vehicle, or with    for the parking brake. Always apply the NEUTRAL if the engine speed is higher than access to an unlocked vehicle.
Page 131: Cold Weather Operation (Below -22°F Or −30°C)
STARTING AND OPERATING To Turn On The Engine Using ENGINE START/STOP EATHER PERATION WARNING! Button –22°F O −30°C) ELOW If the vehicle has a discharged battery,  1. The transmission must be in PARK or NEUTRAL. To ensure reliable starting at these temperatures, booster cables may be used to obtain a start 2.
Page 132: Engine Block Heater - If Equipped
STARTING AND OPERATING NOTE: 4. After the vehicle is running, reattach the cord While cruising, brief full-throttle acceleration within to the hook-and-loop strap and properly stow it the limits of local traffic laws contributes to a good If the ignition switch is left in the ACC or ON/RUN away behind the passenger’s side headlamp.
Page 133 STARTING AND OPERATING The parking brake is primarily intended to prevent your foot is on the brake pedal while you apply the disengages. You may also notice a small amount of movement in the brake pedal. Once the parking the vehicle from rolling while parked. Before parking brake, you may notice a small amount of leaving the vehicle, make sure that the parking brake pedal movement.
Page 134 STARTING AND OPERATING Auto Park Brake WARNING! CAUTION! The Electric Park Brake (EPB) can be programmed If the Brake System Warning Light remains on Never leave children alone in a vehicle, or with  to be applied automatically whenever the vehicle is with the parking brake released, a brake system access to an unlocked vehicle.
Page 135: Automatic Transmission
STARTING AND OPERATING When servicing your rear brakes, it may be WARNING! WARNING! necessary for you or your technician to push the rear piston into the rear caliper bore. With the You can be badly injured working on or around a The transmission may not engage PARK if the ...
Page 136: Ignition Park Interlock
STARTING AND OPERATING be pressed to shift from NEUTRAL into DRIVE or WARNING! CAUTION! REVERSE when the vehicle is stopped or moving at low speeds. When exiting the vehicle, always make sure Before shifting into any gear, make sure your ...
Page 137: Gear Ranges
STARTING AND OPERATING The electronically controlled transmission adapts When parking on a hill, apply the parking brake its shift schedule based on driver inputs, along before shifting the transmission to PARK. As an with environmental and road conditions. The added precaution, turn the front wheels toward the transmission electronics are self-calibrating;...
Page 138 STARTING AND OPERATING The following indicators should be used to ensure WARNING! WARNING! that you have properly engaged the transmission into the PARK position: The transmission may not engage PARK if the When exiting the vehicle, always make sure  ...
Page 139 STARTING AND OPERATING During cold temperatures, transmission operation In the event of a momentary problem, the CAUTION! may be modified depending on engine and transmission can be reset to regain all forward transmission temperature as well as vehicle gears by performing the following steps: Towing the vehicle, coasting, or driving for any speed.
Page 140: All-Wheel Drive (Awd) - If Equipped
STARTING AND OPERATING the vehicle speed drops or during some If the Steering icon is displayed and the “POWER CAUTION! accelerations, the clutch automatically STEERING SYSTEM OVER TEMP” message is disengages. displayed on the instrument cluster screen, this All wheels must have the same size and type indicates an over temperature condition in the tires.
Page 141: Stop/Start System - If Equipped
STARTING AND OPERATING STOP/START SYSTEM — IF EQUIPPED The engine will shut down, the tachometer will HVAC is set to full defrost mode at a high blower  move to the zero position and the Stop/Start speed. The Stop/Start function is developed to reduce telltale will illuminate indicating you are in HVAC is set to MAX A/C.
Page 142: To Start The Engine While In Autostop
STARTING AND OPERATING TART NGINE HILE ANUALLY ANUALLY UTOSTOP TART YSTEM TART YSTEM While in a forward gear, the engine will start when After turning off the Stop/Start system, push the the brake pedal is released or the throttle pedal is Stop/Start OFF switch again (located on the switch pressed.
Page 143: Cruise Control Systems - If Equipped
STARTING AND OPERATING CRUISE CONTROL SYSTEMS — IF EQUIPPED To Activate Push the on/off button to activate the Cruise Your vehicle may be equipped with the Cruise Control. The cruise indicator light in the instrument Control system, or the Adaptive Cruise Control cluster display will illuminate.
Page 144: Adaptive Cruise Control (Acc)
STARTING AND OPERATING To Vary The Speed Setting To Accelerate For Passing To Resume Speed To Increase Or Decrease The Set Speed While the Cruise Control is set, press the To resume a previously set speed, push the RES accelerator to pass as you would normally. When button and release.
Page 145 STARTING AND OPERATING NOTE: WARNING! WARNING! If the ACC sensor detects a vehicle ahead, ACC  The ACC system: You should switch off the ACC system: will apply limited braking or accelerate (not to  exceed the original set speed) automatically to Does not react to pedestrians, oncoming When driving in fog, heavy rain, heavy snow, ...
Page 146 STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation Adaptive Cruise Control (ACC) Menu ACC Proximity Warning  ACC Unavailable Warning The buttons on the right side of the steering wheel The instrument cluster displays the current ACC  operate the ACC system. system settings.The information it displays The instrument cluster display will return to the last depends on ACC system status.
Page 147 STARTING AND OPERATING To Activate/Deactivate NOTE: NOTE: Fixed Speed Cruise Control can be used without Keeping your foot on the accelerator pedal can Push and release the Adaptive Cruise Control  ACC enabled. To change between the different cause the vehicle to continue to accelerate (ACC) on/off button.
Page 148 STARTING AND OPERATING The following conditions will only cancel the ACC pedal to reengage the Adaptive Cruise Control If the button is continually pushed, the set  system: (ACC) to the existing set speed. speed will continue to adjust in 5 mph incre- ments until the button is released.
Page 149 STARTING AND OPERATING When ACC Is Active vehicle speed, ACC calculates and sets the If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle distance to the vehicle ahead. This distance When you use the SET (-) button to decelerate, if ...
Page 150 STARTING AND OPERATING NOTE: NOTE: cases, the instrument cluster display will show “ACC/AEB Unavailable Wipe Front Radar Sensor” The “BRAKE!” screen in the instrument cluster After the ACC system holds your vehicle at a stand- and the system will deactivate. display is a warning for the driver to take action still for approximately three consecutive minutes, and does not necessarily mean that the Forward...
Page 151 STARTING AND OPERATING If the sensor or front end of the vehicle is Limited Functionality Clean Front Windshield” and SERVICE ACC/FCW WARNING  damaged due to a collision, see an authorized the system will have degraded performance. If the system turns off, and the instrument cluster dealer for service.
Page 152 STARTING AND OPERATING OFFSET DRIVING USING ACC ON HILLS ACC may not detect a vehicle in the same lane that ACC performance may be limited when driving on is offset from your direct line of travel, or a vehicle hills. ACC may not detect a vehicle in your lane merging in from a side lane.
Page 153: Parksense Front/Rear Park Assist System - If Equipped
STARTING AND OPERATING PARKSENSE FRONT/REAR PARK ASSIST STATIONARY OBJECTS AND VEHICLES The automatic braking function may not provide  enough vehicle deceleration to avoid colliding ACC does not react to stationary objects or SYSTEM — IF EQUIPPED with a detected obstacle depending on vehicle vehicles.
Page 154: Parksense Sensors
STARTING AND OPERATING ParkSense will retain the last system state (enabled ENSE ENSORS ENSE ISPLAY or disabled) from the last ignition cycle when the The six ParkSense sensors (four when vehicle is The warning display will turn on indicating the ignition is changed to the ON/RUN position.
Page 155 STARTING AND OPERATING ParkSense Arcs 1 — No Tone/Solid Arc 6 — Fast Tone/Flashing Arc 2 — No Tone/Flashing Arc 7 — Fast Tone/Flashing Arc 3 — Fast Tone/Flashing Arc 8 — Slow Tone/Solid Arc 4 — Continuous Tone/Flashing Arc 9 —...
Page 156 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following charts show the warning alert operation when the system is detecting an obstacle: WARNING ALERTS FOR REAR Greater than Less than Rear Distance...
Page 157: Parksense Warning Display
STARTING AND OPERATING Front Park Assist Audible Alerts NABLING ISABLING ENSE ERVICE ENSE SSIST ParkSense will turn off the Front Park Assist YSTEM ParkSense can be enabled and disabled audible alert (chime) after approximately three with the ParkSense switch located below During vehicle start up, when the ParkSense seconds when an obstacle has been detected, the the Uconnect display.
Page 158: Cleaning The Parksense System
STARTING AND OPERATING If "PARKSENSE UNAVAILABLE WIPE REAR more, once you turn ParkSense off, it remains provide a false indication that an obstacle is SENSORS" or "PARKSENSE UNAVAILABLE WIPE off until you turn it on again, even if you cycle the behind the vehicle.
Page 159: Parksense Active Park Assist System
STARTING AND OPERATING into a parallel or a perpendicular parking space on NABLING ISABLING CAUTION! either side (i.e., driver side or passenger side). ENSE CTIVE SSIST ParkSense is only a parking aid and it is  NOTE: YSTEM unable to recognize every obstacle, including The driver is always responsible for controlling ...
Page 160: Parallel/Perpendicular Parking Space Assistance Operation
STARTING AND OPERATING The driver’s door is opened. When pushed, the LED on the ParkSense Active  Park Assist switch will blink momentarily, and then The liftgate is opened.  the LED will turn off if any of the above conditions Electronic Stability Control/Anti-Lock Braking ...
Page 161 STARTING AND OPERATING NOTE: When an available parking space has been found, and the vehicle is not in position, you will be When searching for a parking space, use the  instructed to move forward to position the vehicle turn signal indicator to select which side of the for a perpendicular or parallel parking sequence vehicle you want to perform the parking (depending on the type of maneuver being...
Page 162: Lanesense - If Equipped
STARTING AND OPERATING When the vehicle is in the parking position, the The system will cancel the maneuver if the  CAUTION! maneuver is complete and the driver will be vehicle speed exceeds 5 mph (7 km/h) during instructed to check the vehicle's parking position, active steering guidance into the parking space.
Page 163: Turning Lanesense On Or Off
STARTING AND OPERATING When both lane markings are detected and the URNING ENSE driver drifts out of the lane (no turn signal applied), The LaneSense button is located on the the LaneSense system provides a haptic warning switch panel below the Uconnect display. in the form of torque applied to the steering wheel, as well as a visual warning in the instrument cluster display, to prompt the driver to remain...
Page 164 STARTING AND OPERATING Lane Approached With Flashing Yellow Line/Flashing Lanes Sensed (White Lines) With Green Telltale Lane Drift With Solid Yellow Line/Solid Yellow Telltale Yellow Telltale When the LaneSense system senses a lane drift When the LaneSense system senses the lane ...
Page 165: Changing Lanesense Status
STARTING AND OPERATING The system will not apply torque to the steering A touchscreen button to disable display of the  wheel whenever a safety system engages camera image is made available when the vehicle (Anti-Lock Brakes, Traction Control System, is not in REVERSE gear.
Page 166: Surround View Camera System - If Equipped
STARTING AND OPERATING SURROUND VIEW CAMERA SYSTEM — the vehicle is shifted into PARK, or the ignition is WARNING! placed in the OFF position. There is a touchscreen IF EQUIPPED button “X” to disable the display of the camera Drivers must be careful when backing up even image.
Page 167 STARTING AND OPERATING When enabled, active guidelines are overlaid on Rear View. The Top View will be disabled when this the image to illustrate the width of the vehicle, is selected. including the side view mirrors and its projected Front View Plus Top View backup path based on the steering wheel position.
Page 168: Famcam System - If Equipped
STARTING AND OPERATING FAMCAM SYSTEM — IF EQUIPPED If the vehicle is in PARK, Zoom View is available until WARNING! the gear selector is placed in DRIVE or REVERSE and Your vehicle may be equipped with a FamCam speeds are at or above 8 mph (13 km/h). Drivers must be careful when backing up even system that consists of an interior monitoring when using the Surround View Camera.
Page 169: Refueling The Vehicle
STARTING AND OPERATING To change the seat shown in the zoomed-in view, WARNING! press a different seat location on the left side of the display. The zoomed-in view will then show the Never add fuel when the engine is running. ...
Page 170: Vehicle Loading
STARTING AND OPERATING VEHICLE LOADING Gross Axle Weight Rating (GAWR) front and rear curb weight values are determined by weighing your vehicle on a commercial scale The GAWR is the maximum permissible load on the before any occupants or cargo are added. ERTIFICATION ABEL front and rear axles.
Page 171: Trailer Towing
STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) Tongue Weight (TW) CAUTION! GVWR is the total allowable weight of your vehicle. The TW is the downward force exerted on the hitch Do not load your vehicle any heavier than the This includes driver, passengers, cargo and tongue ball by the trailer.
Page 172: Trailer Hitch Classification
STARTING AND OPERATING Weight-Distributing Hitch depending on vehicle and trailer configuration/ RAILER ITCH LASSIFICATION loading to comply with GAWR requirements. A weight-distributing hitch works by applying The following chart provides the industry standard leverage through spring (load) bars. They are for the maximum trailer weight a given trailer hitch WARNING! typically used for heavier loads to distribute trailer...
Page 173: Trailer Towing Weights
STARTING AND OPERATING RAILER OWING EIGHTS AXIMUM RAILER EIGHT ATINGS The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Trailer Tow Engine/Transmission GCWR Frontal Area Maximum GTW Maximum Trailer TW Package 8,600 lb (3,900 kg) 40 sq ft (3.72 sq m) 3,600 lb (1,632 kg) 360 lb (163 kg)
Page 174 STARTING AND OPERATING Max Cargo With Max Max Trailer TW, Max Number Of Persons / Weight Of Occupants Max Cargo No Trailer Trailer TW 360 lb Trailer (136 kg) 1,205 lb (546 kg) – 360 lb (136 kg) = 845 lb (383 kg) 2 People / 300 lb (136 kg) 1205 lb (546 kg) 845 lb (383 kg)
Page 175: Trailer And Tongue Weight
STARTING AND OPERATING RAILER ONGUE EIGHT OWING EQUIREMENTS WARNING! Never exceed the maximum tongue weight To promote proper break-in of your new vehicle When hauling cargo or towing a trailer, do not  stamped on your fascia/bumper or trailer hitch. drivetrain components, the following guidelines overload your vehicle or trailer.
Page 176 STARTING AND OPERATING Towing Requirements — Trailer Brakes WARNING! CAUTION! Do not interconnect the hydraulic brake system  Total weight must be distributed between the  If the trailer weighs more than 1,000 lb (453 kg) or vacuum system of your vehicle with that of tow vehicle and the trailer such that the loaded, it should have its own brakes and they the trailer.
Page 177: Towing Tips
STARTING AND OPERATING NOTE: OWING Disconnect trailer wiring connector from the  Before towing, practice turning, stopping, and vehicle before launching a boat (or any other backing up the trailer in an area located away from device plugged into vehicle’s electrical connect) heavy traffic.
Page 178: Recreational Towing (Behind Motorhome)
STARTING AND OPERATING RECREATIONAL TOWING When towing your vehicle, always follow appli- Recreational Towing  cable state and provincial laws. Contact state Front-Wheel Drive (FWD) Models (BEHIND MOTORHOME) and provincial Highway Safety offices for addi- Recreational towing is allowed ONLY if the front tional details.
Page 179: Driving Tips
STARTING AND OPERATING All-Wheel Drive (AWD) Models RIVING HROUGH ATER WARNING! Recreational towing (with all four wheels on the Driving through water more than a few inches/ Rapid acceleration on slippery surfaces is dan- ground, or using a towing dolly) is NOT ALLOWED. centimeters deep will require extra caution to gerous.
Page 180 STARTING AND OPERATING WARNING! CAUTION! CAUTION! Always check the depth of the standing water Driving through standing water limits your Driving through standing water may cause    before driving through it. Never drive through vehicle’s braking capabilities, which increases damage to your vehicle’s drivetrain compo- stopping distances.
Page 181: Multimedia
MULTIMEDIA UCONNECT SYSTEMS require software updates to improve the usability NOTE: and performance of your systems or to reduce the FCA US LLC or your dealer may contact you  For detailed information about your Uconnect 5 With potential risk of unauthorized and unlawful access directly regarding software updates.
Page 182: Uconnect Settings
MULTIMEDIA UCONNECT SETTINGS For the Uconnect 5 With 7-inch Display and the USTOMER ROGRAMMABLE EATURES Uconnect 5/5 NAV With 10.1-inch Display The Uconnect system uses a combination of Press the Vehicle button, then press the Settings buttons on the touchscreen and buttons on the tab on the top of the touchscreen.
Page 183 MULTIMEDIA KeySense The vehicle’s KeySense settings are protected by a unique four-digit PIN, which the vehicle owner creates when accessing the specific settings for the first time. This four-digit PIN can only be reset by an authorized dealer. After pressing the KeySense button on the touchscreen, and entering the KeySense PIN, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 184 MULTIMEDIA Setting Name Description This setting will change the type of alert provided when an object is detected in a vehicle’s blind spot. The “Lights” setting will activate the Blind Spot Alert Blind Spot Alert lights on the outside mirrors. The “Lights & Chime” setting will activate both the lights on the outside mirrors and an audible chime.
Page 185 MULTIMEDIA Setting Name Description This setting will allow you to set the brightness when the headlights are off. To Display Brightness Headlights Off access this setting, Display Mode must be set to “Manual”. The “+” setting will increase the brightness; the “-” will decrease the brightness. Set Theme This setting will allow you to change the theme of the radio.
Page 186 MULTIMEDIA Setting Name Description Show Command List This setting will allow the Command List to be shown on or off. This setting will keep certain electrical features running after the engine is Key Off Power Delay turned off. When any door is opened, the electronics will deactivate. The available settings are “0 sec”, “45 sec”, “5 min”, and “10 min”.
Page 187 MULTIMEDIA Setting Name Description This setting will return all the previously changed settings to their factory Restore Settings to Default default. More Profile Options This setting will give access to more profile options. Display After pressing the Display button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 188 MULTIMEDIA Setting Name Description This setting changes the “Speed” (MPH or km/h), “Distance” (mi or km), “Fuel Consumption” (MPG [US], MPG [UK], L/100 km, or km/L), “Pressure” (psi, Units kPa, or bar), “Temperature” (°C or °F), and “Current Consumption” (MPG [US], MPG [UK], L/100 km, or km/L) units of measurement independently.
Page 189 MULTIMEDIA Safety & Driving Assistance After pressing the Safety & Driving Assistance button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.
Page 190 MULTIMEDIA Setting Name Description This setting will change the type of ParkSense alert when a close object is detected. The “Sound Only” setting will provide an audible chime when an ParkSense object is detected. The “Sound and Display” setting will provide both an audible chime and a visual display when an object is detected.
Page 191 MULTIMEDIA Clock & Date After pressing the Clock & Date button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description This setting will sync the time to the GPS receiver in the system. The system Sync Time With GPS will control the time via the GPS location.
Page 192 MULTIMEDIA Phone/Bluetooth® When the Phone/Bluetooth® button is pressed on the touchscreen, the system displays the options related to Bluetooth® connectivity from an external audio device or smartphone. The list of paired audio devices or smartphones can be accessed from this menu. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 193 MULTIMEDIA Voice — If Equipped After pressing the Voice button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description This setting will allow you to change the voice options for the radio to “Male” Voice Options or “Female”.
Page 194 MULTIMEDIA Camera When the Camera button is pressed on the touchscreen, the system displays the options related to the vehicle’s camera features. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description This setting will add a timed delay to the Surround View Camera when shifting Surround View Camera Delay out of REVERSE.
Page 195 MULTIMEDIA Setting Name Description Rain Sensing Auto Wipers This setting will turn the Rain Sensing Auto Wipers on or off. Headlights With Wipers This setting will turn the headlights on when the wipers are activated. Lights When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle’s exterior and interior lights. NOTE: When the “Daytime Running Lights”...
Page 196 MULTIMEDIA Brakes After pressing the Brakes button on the touchscreen, the following settings will be available: NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Auto Park Brake This setting will turn the Auto Park Brake on or off. Brake Service This setting will allow you to retract the brakes for servicing.
Page 197 MULTIMEDIA Setting Name Description This setting will sound the horn when the Lock button is pushed on the key fob. The “Off” setting will not sound the horn when the Lock button is pushed. Sound Horn With Lock The “1st Press” setting will sound the horn when the Lock button is pushed once.
Page 198 MULTIMEDIA Seats & Comfort When the Seats & Comfort button is pressed on the touchscreen, the system displays the options related to the vehicle’s comfort systems when remote start has been activated or the vehicle has been started. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description This setting will activate the vehicle’s comfort systems and heated seats or...
Page 199 MULTIMEDIA Key Off Options When the Key Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff. These settings will only activate when the ignition is set to OFF. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description Easy Exit Seat...
Page 200 MULTIMEDIA Audio When the Audio button is pressed on the touchscreen, the system displays options related to the vehicle’s sound system. These settings can change the audio location within the vehicle, adjust the bass or treble levels, and auto-play settings from an audio device or smartphone. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 201 MULTIMEDIA Notifications When the Notifications button is pressed on the touchscreen, the system displays the options related to Notifications for the system. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description App Drawer Favoriting Popups This setting turns the “App Favorited” pop-up on or off. App Drawer Unfavoriting Popups This setting turns the “App Unfavorited”...
Page 202 MULTIMEDIA SiriusXM® Setup When the SiriusXM® Setup button is pressed on the touchscreen, the system displays options related to SiriusXM® satellite radio. These settings can be used to skip specific radio channels and restart favorite songs from the beginning. NOTE: A subscription to SiriusXM®...
Page 203 MULTIMEDIA Software Updates When the Software Updates button is pressed on the touchscreen, the system will display information on updating the Uconnect system’s software. NOTE: Depending on the vehicle’s options, feature settings may vary. Setting Name Description This setting will allow software updates to happen over Wi-Fi. Selectable Software Downloads over Wi-Fi options for the setting are “On”...
Page 204 MULTIMEDIA Reset When the Reset button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings. These settings can clear personal data and reset selected settings from other menus. NOTE: Depending on the vehicle’s options, feature settings may vary.
Page 205: Rear Seat Entertainment With Amazon Firetv Built-In - If Equipped
MULTIMEDIA REAR SEAT ENTERTAINMENT WITH ETTING TARTED CCESSING NTERTAINMENT WITH MAZON AMAZON FIRETV BUILT-IN — IF EQUIPPED UILT IN FROM THE ADIO VERVIEW You can access your Rear Seat Entertainment system by following the steps below: Rear Seat Entertainment is designed to give your family years of enjoyment.
Page 206: Accessing Rear Seat Entertainment With Amazon Firetv Built-In From The Rear Screens
MULTIMEDIA Remote Pairing Account Sign-in CCESSING After the boot up sequence is complete, the The next step will be the option to sign in to your NTERTAINMENT WITH MAZON system will then give the option to pair the Rear Amazon account. UILT IN FROM THE CREENS...
Page 207: Rear Screen Fly-Out Menu
MULTIMEDIA 5. In the Settings, select “Controllers & CREEN ARENTAL ONTROLS SING THE Bluetooth® Devices”. CREENS Accessing the rear screen fly-out menu will give 6. Then from this menu, select “Add New more options for Rear Seat Entertainment. If parental controls were not set during the first Remote”.
Page 208: Rear Seat Entertainment Remote Control
MULTIMEDIA Down, Left, or Right to navigate on-screen for ‖ — Begin/resume or NTERTAINMENT EMOTE 14. Play/Pause Button selections and pushing the center button to pause disc play. ONTROL confirm selections. 15. Channel +/- — Push the up or down arrow 3.
Page 209: Rear Seat Entertainment With Amazon Firetv Built-In Streaming (Using The Radio And Rear Screens)
MULTIMEDIA USB Video — Under “USB Videos”, videos will To access Amazon FireTV Built-in on the front NTERTAINMENT WITH  appear that are options with a USB device screen, select “Launch Source” on the front radio TV B MAZON UILT TREAMING connected to Rear Seat Entertainment.
Page 210: Playa Blu Ray Or Dvd
MULTIMEDIA Back — This will let you go back the previous 4. To play a Blu-ray™ or DVD disc on both screens  CREEN NTERTAINMENT WITH page. simultaneously, select “Launch Source” and TV B MAZON UILT then under Inputs, select “View Screen 1 or 2”. FireTV Home —...
Page 211: Using The Video Usb Port
MULTIMEDIA USB P SING IDEO IDEO AMES EADPHONES PERATION Plug in a USB drive or mass storage device and Connect the video game console to either of the Rear Seat Entertainment does not come equipped play your favorite music or movies. HDMI ports located behind the first row seat.
Page 212: Rear Climate Controls
MULTIMEDIA LIMATE ONTROLS The Rear Climate Controls can also be controlled using Rear Seat Entertainment Ú page 69. Rear Climate Controls can be accessed by using the Car menu. Swipe up or down on either rear screen and select the Car icon or press the Car button on the Rear Seat Entertainment remote.
Page 213 MULTIMEDIA Icon Description Headliner Mode Headliner Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow. Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets.
Page 214: Legal Notice
MULTIMEDIA RADIO OPERATION AND MOBILE PHONES EGAL OTICE EGULATORY AFETY NFORMATION To access Legal and Compliance information Under certain conditions, the mobile phone being about Rear Seat Entertainment from the rear on in your vehicle can cause erratic or noisy US/CANADA screens, follow the steps below: performance from your radio.
Page 215: Safety
SAFETY SAFETY FEATURES You also may experience the following normal WARNING! characteristics when the ABS activates: (ABS) Pumping of the Anti-Lock Brakes will diminish RAKE YSTEM  ABS motor noise or clicking sounds (you may  their effectiveness and may lead to a collision. continue to hear for a short time after the stop) If applicable, refer to the “Hybrid Supplement”...
Page 216: Electronic Brake Control (Ebc) System
SAFETY Anti-Lock Brake System (ABS) Warning Assist (HSA), and Traction Control System WARNING! (TCS).These systems work together to enhance Light both vehicle stability and control in various driving The Brake Assist System (BAS) cannot prevent The yellow ABS Warning Light will turn on when the conditions.
Page 217 SAFETY Dynamic Steering Torque (DST) Electronic Roll Mitigation (ERM) Electronic Stability Control (ESC) DST is a feature of the ESC and Electric Power ERM anticipates the potential for wheel lift by ESC enhances directional control and stability of Steering (EPS) modules that provides torque at the monitoring the driver’s steering wheel input and the vehicle under various driving conditions.
Page 218 SAFETY ESC Operating Modes pushing the ESC OFF button. This may be done WARNING! while the vehicle is in motion. Depending upon model and mode of operation, the Electronic Stability Control (ESC) cannot  ESC system may have multiple operating modes. WARNING! prevent the natural laws of physics from acting ESC On...
Page 219 SAFETY The ESC Activation/Malfunction Indicator Light Hill Start Assist (HSA) WARNING! starts to flash as soon as the tires lose traction and HSA is designed to mitigate roll back from a the ESC system becomes active. The ESC There may be situations where the Hill Start complete stop while on an incline.
Page 220 SAFETY Ready Alert Braking (RAB) wheel on a driven axle is spinning faster than the WARNING! other, the system will apply the brake of the RAB may reduce the time required to reach full spinning wheel. This will allow more vehicle torque If you use a trailer brake controller with your ...
Page 221: Auxiliary Driving Systems
SAFETY AUXILIARY DRIVING SYSTEMS The BSM detection zone covers approximately one The area on the rear fascia/bumper where the lane width on both sides of the vehicle 12 ft radar sensors are located must remain free of (BSM) — (3.7 m). The zone length starts at the outside snow, ice, and dirt/road contamination so that the LIND ONITORING...
Page 222 SAFETY If the blockage message is still present after Overtaking Traffic cycling the ignition and driving in traffic, check If you pass another vehicle slowly with a relative again for a blockage. speed less than 15 mph (24 km/h) and the vehicle The BSM system notifies the driver of objects in the remains in the blind spot for approximately 1.5 detection zones by illuminating the BSM Warning...
Page 223 SAFETY Rear Cross Path (RCP) RCP is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The RCP system will then have a clear view of the cross traffic and if an oncoming vehicle is detected, alert the driver.
Page 224 SAFETY NOTE: Blind Spot Modes NOTE: In a parking lot situation, oncoming vehicles can be Whenever an audible alert is requested by the Three selectable modes of operation are available blocked by vehicles parked on either side. If the BSM system, the radio is also muted. in the Uconnect system.
Page 225: Forward Collision Warning (Fcw) With Mitigation - If Equipped
SAFETY (FCW) If a FCW with Mitigation event begins at a speed NOTE: ORWARD OLLISION ARNING below 37 mph (60 km/h), the system may provide — I The minimum speed for FCW activation is  ITIGATION QUIPPED the maximum braking possible to mitigate the 1 mph (2 km/h).
Page 226 SAFETY Turning FCW On Or Off By changing the FCW status setting to "Far", the that are far away, oncoming traffic, or leading system provides possible collision warnings on vehicles with the same or higher rates of speed. The Forward Collision menu setting is located in objects farther away.
Page 227: Tire Pressure Monitoring System (Tpms)
SAFETY Pedestrian Emergency Braking (PEB) — The minimum speed for PEB activation is 3 mph NOTE: (5 km/h). The PEB system will NOT retain the last setting If Equipped selected by the driver after ignition shut down. The PEB is a subsystem of the FCW system which WARNING! system will reset to the default setting when the provides the driver with audible and visual...
Page 228 SAFETY The system will automatically update and the The tire pressure will vary with temperature by CAUTION! approximately 1 psi (7 kPa) for every 12°F (6.5°C). TPMS Warning Light will turn off once the system This means that when the outside temperature receives the updated tire pressures.
Page 229 SAFETY NOTE: NOTE: Jamming due to electronic devices or driving  It is particularly important for you to check the tire next to facilities emitting the same radio The TPMS is not intended to replace normal tire  frequencies as the TPMS sensors pressure in all of the tires on your vehicle monthly care and maintenance, or to provide warning of and to maintain the proper pressure.
Page 230 SAFETY 4. For each subsequent ignition cycle, a chime assemblies that do not have TPMS sensors, such will sound, the TPMS Warning Light will flash as when installing winter wheel and tire on and off for 75 seconds and then remain on assemblies on your vehicle.
Page 231: Occupant Restraint Systems
SAFETY OCCUPANT RESTRAINT SYSTEMS belt-positioning booster seat in a rear seating WARNING! position Ú page 251. Some of the most important safety features in your Never place a rear-facing child restraint in 3. If a child from 2 to 12 years old (not in a ...
Page 232 SAFETY Enhanced Seat Belt Use Reminder System outboard front passenger seat is unoccupied). The NOTE: BeltAlert warning sequence starts by blinking the If BeltAlert has been deactivated and the driver or (BeltAlert) Seat Belt Reminder Light and sounding an outboard front seat passenger (if equipped with Driver And Passenger BeltAlert —...
Page 233 SAFETY WARNING! WARNING! WARNING! In a collision, you and your passengers can Two people should never be belted into a A seat belt that is too loose will not protect you    suffer much greater injuries if you are not single seat belt.
Page 234 SAFETY the shoulder belt. To loosen the lap belt if it is WARNING! too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding A frayed or torn seat belt could rip apart in a ...
Page 235 SAFETY Lap/Shoulder Belt Untwisting Procedure WARNING! Use the following procedure to untwist a twisted Wearing your seat belt incorrectly could make  lap/shoulder belt. your injuries in a collision much worse. You 1. Position the latch plate as close as possible to might suffer internal injuries, or you could the anchor point.
Page 236 SAFETY headliner for added convenience to open up 4. When the seat belt is long enough to fit, insert utilization of the storage areas behind the front the mini-latch plate into the mini-buckle until seats when the seat is not occupied. you hear a “click.”...
Page 237 SAFETY 5. Sit back in seat. Slide the regular latch plate up 10. To disengage the mini-latch plate from the mini-buckle for storage, insert the regular latch the webbing as far as necessary to allow the seat belt to go around your lap. plate into the center red slot on the mini-buckle.
Page 238 SAFETY Position the lap belt snug and low below the WARNING! WARNING! abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away When reattaching the mini-latch plate and Using a Seat Belt Extender when not needed ...
Page 239 SAFETY Energy Management Feature The front outboard seat belt system is equipped with an Energy Management feature that may help further reduce the risk of injury in the event of a collision. The seat belt system has a retractor assembly that is designed to release webbing in a controlled manner.
Page 240 SAFETY Seat Belt Park Stitch — If Equipped In Automatic Locking Mode, the shoulder belt is 3. Allow the seat belt to retract. As the seat belt automatically pre-locked. The seat belt will still retracts, you will hear a clicking sound. This The rear outboard seat belts may be equipped with retract to remove any slack in the shoulder belt.
Page 241: Supplemental Restraint Systems (Srs)
SAFETY Third Row Stow Clip — If Equipped Seat Track Position Sensors UPPLEMENTAL ESTRAINT YSTEMS  (SRS) Occupant Classification System Your vehicle may be equipped with a stow clip on  the lower trim behind the third row. This clip is used Air Bag Warning Light Some of the safety features described in this to hold the seat belt out of the path of the power...
Page 242 SAFETY Redundant Air Bag Warning Light is designed to be maintenance free, if any of the following occurs, have an authorized dealer If a fault with the Air Bag Warning Light is service the air bag system immediately. detected, which could affect the The Air Bag Warning Light does not come on ...
Page 243 SAFETY detects whether the driver or front passenger seat WARNING! WARNING! belt is buckled. The seat belt buckle switch may adjust the inflation rate of the Advanced Front Air Never place a rear-facing child restraint in Relying on the air bags alone could lead to ...
Page 244 SAFETY Seat belts are necessary for your protection in all Advanced Front Air Bag output appropriate to the Advanced Front Air Bag deployment based on collisions, and also are needed to help keep you in occupant’s seated weight, as determined by the occupant classification.
Page 245 SAFETY Sitting upright Failure to do so may result in serious injury or  WARNING! death. The OCS determines the most probable Facing forward  classification of the occupant that it detects. The Never place a rear-facing child restraint in ...
Page 246 SAFETY Objects are lodged between the front passenger  seat and center console. Accessories that may change the seated weight  on the front passenger seat are attached to the front passenger seat. Anything that may decrease or increase the ...
Page 247 SAFETY function as designed. Do not make any WARNING! WARNING! modifications to the front passenger seat components, assembly, or to the seat cover. If the Unapproved modifications or service proce- Do not carry or hold any objects (e.g., back-  ...
Page 248 SAFETY Supplemental Driver And Front Passenger Supplemental Side Air Bag Inflatable Curtains (SABICs) Knee Air Bags This vehicle is equipped with Supplemental Side This vehicle is equipped with a Supplemental Air Bag Inflatable Curtains (SABICs). Driver Knee Air Bag mounted in the instrument panel below the steering column and a Supplemental Side Air Bag Inflatable Curtains Supplemental Passenger Knee Air Bag mounted in...
Page 249 SAFETY The SABIC deploys downward, covering the side Side Impacts WARNING! windows. An inflating SABIC pushes the outside The Side Air Bags are designed to activate in edge of the headliner out of the way and covers the Occupants, including children, who are up certain side impacts.
Page 250 SAFETY If A Deployment Occurs The SABICs may help reduce the risk of partial or WARNING! complete ejection of vehicle occupants through The front air bags are designed to deflate side windows in certain rollover or side impact Relying on the Side Air Bags alone could lead ...
Page 251 SAFETY Do not drive your vehicle after the air bags have Flash hazard lights as long as the battery has battery. Carefully check the vehicle for fuel leaks in  deployed. If you are involved in another collision, power. the engine compartment and on the ground near the air bags will not be in place to protect you.
Page 252 SAFETY Maintaining Your Air Bag System Whether or not the driver and passenger safety  WARNING! belts were buckled/fastened; WARNING! Do not attempt to modify any part of your air  How far (if at all) the driver was depressing the ...
Page 253: Child Restraints
SAFETY and follow all the instructions and warnings in the HILD ESTRAINTS WARNING! child restraint Owner’s Manual and on all the Everyone in your vehicle needs to be buckled up at labels attached to the child restraint. In a collision, an unrestrained child can become all times, including babies and children.
Page 254 SAFETY Infant And Child Restraints Older Children And Child Restraints WARNING! Safety experts recommend that children ride Children who are two years old or who have Never install a rear-facing child restraint in the  rear-facing in the vehicle until they are two years outgrown their rear-facing convertible child seat front seat of a vehicle.
Page 255 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no”, WARNING! then the child still needs to use a booster seat in Children who are large enough to wear the this vehicle. If the child is using the lap/shoulder After a child restraint is installed in the ...
Page 256 SAFETY Recommendations For Attaching Child Restraints Use Any Attachment Method Shown With An “X” Below Combined Weight of Restraint Type the Child + Child LATCH – Lower Anchors LATCH – Lower Anchors Seat Belt + Top Tether Seat Belt Only Restraint Only + Top Tether Anchor...
Page 257 SAFETY LATCH Positions For Installing Child Restraints In This Vehicle If applicable, refer to the “Hybrid Supplement” for additional information. 7 Passenger Stow ‘n Go Seating LATCH Positions 8 Passenger LATCH Positions Lower Anchorage Symbol (2 anchorages per Lower Anchorage Symbol (2 anchorages per seating position) seating position) Top Tether Anchorage Symbol...
Page 258 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of What is the weight limit (child’s weight + weight of the child the child and the child restraint is 65 lbs (29.5 kg). Use the seat restraint) for using the LATCH anchorage system to attach the 65 lbs (29.5 kg) belt and tether anchor instead of the LATCH system once the...
Page 259 SAFETY Locating The LATCH Anchorages WARNING! If applicable, refer to the “Hybrid Supplement” for Always make sure the head restraint is in its additional information. upright position when the seat is to be used by The lower anchorages are round bars an occupant who is not in a child restraint.
Page 260 SAFETY Locating The Upper Tether Anchorages If applicable, refer to the “Hybrid Supplement” for additional information. There are tether strap anchorages located behind all second row seating positions. The third row has a tether anchor on the 40% seat for the right outboard position and in the center of the 60% seat for either the center or left outboard seating position.
Page 261 SAFETY Center Seat LATCH 2. Place the child seat between the lower WARNING! anchorages for that seating position. If the This vehicle has 4 lower LATCH anchorages in the second row seat can be reclined, you may Use anchorages C and D to install a ...
Page 262 SAFETY How To Stow An Unused Switchable-ALR The seat belts in the passenger seating positions WARNING! are equipped with a Switchable Automatic Locking (ALR) Seat Belt: Retractor (ALR) that is designed to keep the lap Child restraint anchorages are designed to ...
Page 263 SAFETY Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle If applicable, refer to the “Hybrid Supplement” for additional information. 7 Passenger Stow ‘n Go Seating Automatic Locking 8 Passenger Automatic Locking Retractor (ALR) Locations Retractor (ALR) Locations ALR — Switchable Automatic Locking Retractor ALR —...
Page 264 SAFETY Frequently Asked Questions What is the weight limit (child’s weight + weight of the child Always use the tether anchor when using the seat belt to install a Weight limit of the restraint) for using the Tether Anchor with the seat belt to attach forward facing child restraint, up to the recommended weight Child Restraint a forward facing child restraint?
Page 265 SAFETY Installing A Child Restraint With A 2. Pull enough of the seat belt webbing from the 8. If the child restraint has a top tether strap and retractor to pass it through the belt path of the the seating position has a top tether Switchable Automatic Locking Retractor child restraint.
Page 266 SAFETY Installing Child Restraints Using The Top Tether Anchorage If applicable, refer to the “Hybrid Supplement” for additional information. WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage.
Page 267 SAFETY Third Row Tether Attachment The tether anchorage found on the back of the 60% seat in the third row may be used by either the left outboard or the center seating position. Only tether one child restraint to the tether anchorage at a time.
Page 268: Safety Tips
SAFETY 4. Remove slack in the tether strap according to RANSPORTING WARNING! the child restraint manufacturer’s instructions. Air Bags deploying in the front seat could harm Do not connect the tether strap for more than your pet. An unrestrained pet will be thrown about one child restraint to the tether anchorage on and possibly injured, or injure a passenger during the 60% seat in the third row.
Page 269 SAFETY Air Bag Warning Light accelerator, brake or clutch pedals or impair safe WARNING! operation of your vehicle in other ways. The Air Bag Warning Light will turn on for ONLY use the driver’s side floor mat on the  four to eight seconds as a bulb check WARNING! driver’s side floor area.
Page 270: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY Lights WARNING! WARNING! Have someone observe the operation of brake If the vehicle carpet has been removed and If you are required to drive with the trunk/lift-   lights and exterior lights while you work the re-installed, always properly attach carpet to gate/rear doors open, make sure that all controls.
Page 271: Carbon Monoxide Warnings
SAFETY ARBON ONOXIDE ARNINGS WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases. They contain  carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 272: In Case Of Emergency
IN CASE OF EMERGENCY HAZARD WARNING FLASHERS When you must leave the vehicle to seek If equipped, the rearview mirror contains an SOS assistance, the Hazard Warning Flashers will and ASSIST button. The Hazard Warning Flashers button is located in continue to operate even though the ignition is the lower center area of the instrument panel.
Page 273 IN CASE OF EMERGENCY ASSIST Call 2. The LED light located between the SOS and NOTE: ASSIST buttons on the Rearview Mirror will The ASSIST Button is used to automatically Your vehicle may be transmitting data as  turn green once a connection to a SOS authorized by the subscriber.
Page 274 IN CASE OF EMERGENCY SOS Call System Limitations WARNING! WARNING! Vehicles sold in Mexico DO NOT have SOS Call Never place anything on or near the vehicle’s The Occupant Restraint Control module turns  system capabilities.  operable network and GPS antennas. You could on the air bag Warning Light on the instrument SOS or other emergency line operators in Mexico prevent operable network and GPS signal...
Page 275: Jacking And Tire Changing
IN CASE OF EMERGENCY LTE (voice/data) or 4G (data) network conges- NOTE:  WARNING! tion Changes or modifications not expressly approved by the party responsible for compliance could void Being under a jacked-up vehicle is dangerous.  Weather  the user's authority to operate the equipment. The vehicle could slip off the jack and fall on Buildings, structures, geographic terrain, or ...
Page 276: Jack And Spare Tire Location
IN CASE OF EMERGENCY 4. Place the gear selector into PARK (P). 5. Place the ignition in OFF mode. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the driver’s front wheel is being changed, block the passenger’s rear wheel.
Page 277: Jacking Instructions
IN CASE OF EMERGENCY WARNING! Block the wheel diagonally opposite the wheel  to be raised. Do not let any passenger sit in the vehicle  when it is on a jack. Do not get under the vehicle when it is on a ...
Page 278 IN CASE OF EMERGENCY CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. Detailed information about the inflatable spare tire, its use, and operation Ú page 335. Jacking Locations Front Jack Location Extending The Wrench...
Page 279 IN CASE OF EMERGENCY raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw clockwise using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the compact spare tire.
Page 280: Road Tire Installation
IN CASE OF EMERGENCY 8. Inflate the tire to the prescribed pressure tire location. Have the full-sized tire repaired or NSTALLATION 60 psi (4.2 Bar) using the Portable Air replaced, as soon as possible. Vehicles Equipped With Wheel Covers Compressor Ú page 279 or Tire Service Kit if 13.
Page 281: Portable Air Compressor - If Equipped
IN CASE OF EMERGENCY 3. Align the valve notch in the wheel cover with twice Ú page 343. If in doubt about the 1 — Power Plug correct tightness, have them checked with a the valve stem on the wheel. Install the cover 2 —...
Page 282: Return Inflatable Spare Tire
IN CASE OF EMERGENCY 6. Switch the power button ON. 4. Install the foam tray with wrench and funnel WARNING! installed. Always stow the Portable Air Compressor only  5. Install and tighten the wing nut by hand. in the provided place. 7.
Page 283 IN CASE OF EMERGENCY Tire Service Kit Storage The Tire Service Kit is secured with a strap and is 1 — Sealant/Air Hose stored under the load floor within the second row. 2 — Hose Accessories 3 — Mode Select Knob 4 —...
Page 284 IN CASE OF EMERGENCY Using The Power Button The Tire Service Kit Sealant is only intended to   WARNING! seal punctures less than 1/4 inch (6 mm) diam- Push and release the Power Button eter in the tread/contact surface of your If the tire has any sidewall damage.
Page 285 IN CASE OF EMERGENCY the sealant into the deflated tire and running 2. Ensure the Mode Select Knob is to the WARNING! the air pump. Move the vehicle as necessary to Sealant Mode position. place the valve stem in this position before Take care not to allow the contents of Tire ...
Page 286 IN CASE OF EMERGENCY If the sealant (white fluid) does flow through the 1. Push the Power Button to turn the Tire After Driving: Sealant Hose: Service Kit off. Pull over to a safe location and turn on the  1.
Page 287 IN CASE OF EMERGENCY 4. Uncoil the Power Plug and insert the 2. Disconnect the Tire Service Kit from the valve plug into the vehicle's 12 Volt power stem, reinstall the cap on the valve stem and outlet. unplug from 12 Volt outlet. 5.
Page 288: Jump Starting
IN CASE OF EMERGENCY NOTE: 4. Rotate the bottle up beyond vertical to release. CAUTION! For sealant bottle installation, follow these  Do not use a portable battery booster pack or steps reverse order. any other booster source with a system voltage Replacement sealant bottles are available at ...
Page 289: Jump Starting Procedure
IN CASE OF EMERGENCY Only jump directly off positive post which has a Connecting The Jumper Cables WARNING! positive (+) symbol on or around the post. 1. Connect the positive (+) end of the jumper Remove any metal jewelry such as rings, See below steps to prepare for jump starting: ...
Page 290: Refueling In Emergency - If Equipped
IN CASE OF EMERGENCY REFUELING IN EMERGENCY – IF EQUIPPED Disconnecting The Jumper Cables Emergency Gas Can Refueling 1. Disconnect the negative (-) end of the jumper Most gas cans will not open the flapper doors. A The vehicle is equipped with a refueling funnel for cable from the remote negative post of the funnel is provided to allow emergency refueling a Cap-Less Fuel System Ú...
Page 291: If Your Engine Overheats
IN CASE OF EMERGENCY MANUAL PARK RELEASE If your Air Conditioner (A/C) is on, turn it off. The  WARNING! A/C system adds heat to the engine cooling system and turning the A/C off can help remove Never have any smoking materials lit in or ...
Page 292: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY NOTE: NOTE: Follow These Steps To Activate The Manual Park Release: When the lever is locked in the released position, Shifts between DRIVE and REVERSE can only be the tether will remain outside of the trim panel and achieved at wheel speeds of 5 mph (8 km/h) or 1.
Page 293: Towing A Disabled Vehicle
IN CASE OF EMERGENCY CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for  at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle.
Page 294 IN CASE OF EMERGENCY NOTE: Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars Ensure that the Electric Park Brake is released, and other equipment designed for this purpose, and remains released, while being towed. following equipment manufacturer’s instructions.
Page 295: All Wheel Drive (Awd) Models
IN CASE OF EMERGENCY CAUTION! CAUTION! CAUTION! Do not use sling-type equipment when towing. Towing this vehicle using any other method Recovery load should:   Vehicle damage may occur. can cause severe transmission and/or Be applied at constant speed. ...
Page 296: Servicing And Maintenance
SERVICING AND MAINTENANCE SCHEDULED SERVICING An authorized dealer will reset the oil change Once A Month Or Before A Long Trip: indicator message after completing the scheduled Check engine oil level.  Your vehicle is equipped with an automatic oil oil change.
Page 297: Maintenance Plan
SERVICING AND MAINTENANCE AINTENANCE Refer to the Maintenance Plan for required maintenance. At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter.  Rotate the tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. ...
Page 298 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints Inspect front suspension, boot seals, tie rod ends, and replace if necessary Inspect the brake linings, parking brake function Inspect front accessory drive tensioner, idler pulley, and replace if necessary Additional Maintenance Replace engine air cleaner filter...
Page 299 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first Replace PCV valve 1. The spark plug change interval is mileage-based only; yearly intervals do not apply. WARNING! You can be badly injured working on or around a motor vehicle.
Page 300: Engine Compartment
SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L E NGINE 1 — Engine Coolant Pressure Cap 5 — Power Distribution Center (Fuses) 2 — Engine Oil Fill 6 — Windshield Washer Reservoir Cap 3 — Brake Fluid Reservoir Cap 7 — Engine Oil Dipstick 4 —...
Page 301: Checking Oil Level
SERVICING AND MAINTENANCE To prevent freeze-up of your windshield washer HECKING EVEL CAUTION! system in cold weather, select a solution or mixture To ensure proper engine lubrication, the engine oil that meets or exceeds the temperature range of Overfilling or underfilling the crankcase will must be maintained at the correct level.
Page 302: Pressure Washing
SERVICING AND MAINTENANCE RESSURE ASHING WARNING! WARNING! Cleaning the engine compartment with a high You can be badly injured working on or around a Battery gas is flammable and explosive. Keep  pressure washer is not recommended. motor vehicle. Only do service work for which flame or sparks away from the battery.
Page 303: Engine Oil Filter
SERVICING AND MAINTENANCE NGINE ILTER CCESSORY RIVE NSPECTION CAUTION! The engine oil filter should be replaced with a new Do not use chemical flushes in your engine oil as WARNING! filter at every engine oil change. the chemicals can damage your engine. Such Do not attempt to inspect an accessory drive ...
Page 304: Air Conditioner Maintenance
SERVICING AND MAINTENANCE Some conditions can be caused by a faulty WARNING! component such as a belt pulley. Belt pulleys should be carefully inspected for damage and The air conditioning system contains refrig-  proper alignment. erant under high pressure. To avoid risk of personal injury or damage to the system, Belt replacement on some models requires the adding refrigerant or any repair requiring lines...
Page 305 SERVICING AND MAINTENANCE Cabin Air Filter 2. Open the glove compartment door partially, 5. Pry up the lid of each individual compartment snap, and detach it from the rest of the snap. leaving extra slack on the glove compartment WARNING! tension tether.
Page 306: Body Lubrication
SERVICING AND MAINTENANCE 7. Remove the filter cover by prying back each of Operation of the wipers on dry glass for long UBRICATION the retaining tabs from their hooking points, periods may cause deterioration of the wiper Locks and all body pivot points, including such and then pulling the filter cover out to expose blades.
Page 307 SERVICING AND MAINTENANCE Front Wiper Blade Removal/Installation 2. To disengage the wiper blade from the wiper 3. With the wiper blade disengaged, remove the arm, flip up the release tab on the wiper blade wiper blade from the wiper arm by holding the CAUTION! and while holding the wiper arm with one wiper arm with one hand and separating the...
Page 308 SERVICING AND MAINTENANCE Rear Wiper Blade Removal/Installation Installing The Front Wipers 2. Lift the rear wiper arm fully off the glass. 1. Lift the wiper arm off of the glass, until the 1. Lift the rear wiper arm pivot cap away from wiper arm is in the full up position.
Page 309: Exhaust System
SERVICING AND MAINTENANCE 4. Still grasping the bottom end of the wiper NOTE: to seep into the passenger compartment. In blade, move the wiper blade upward and away The rear wiper arm cannot be fully raised off the addition, have the exhaust system inspected each from the wiper arm to disengage.
Page 310: Cooling System
SERVICING AND MAINTENANCE To minimize the possibility of catalytic converter CAUTION! WARNING! damage: Damage to the catalytic converter can result if When working near the radiator cooling fan,  Do not interrupt the ignition when the transmis-   your vehicle is not kept in proper operating disconnect the fan motor lead or turn the igni- sion is in gear and the vehicle is in motion.
Page 311 SERVICING AND MAINTENANCE Cooling System — Drain, Flush And Refill Do not use water alone or alcohol-based engine We recommend using Mopar® Antifreeze/   coolant products. Do not use additional rust Coolant 10 Year/150,000 Mile (240,000 km) NOTE: inhibitors or anti-rust products, as they may not Formula OAT that meets the requirements of the Some vehicles require special tools to add coolant be compatible with the radiator engine coolant...
Page 312 SERVICING AND MAINTENANCE Disposal Of Used Coolant Cooling System Notes damage. If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, Used ethylene glycol-based coolant (antifreeze) is NOTE: flush, and refill with OAT coolant (conforming to a regulated substance requiring proper disposal.
Page 313: Brake System
SERVICING AND MAINTENANCE Make sure that the coolant expansion bottle Brake Master Cylinder  WARNING! overflow hoses are not kinked or obstructed. The fluid in the master cylinder should be checked To avoid contamination from foreign matter or  Keep the front of the radiator clean. If your when performing under hood services or ...
Page 314: Automatic Transmission
SERVICING AND MAINTENANCE UTOMATIC RANSMISSION CAUTION! CAUTION! Special Additives If a transmission fluid leak occurs, visit an Using a transmission fluid other than the authorized dealer immediately. Severe transmis- manufacturer recommended fluid may cause The manufacturer strongly recommends against sion damage may occur. An authorized dealer deterioration in transmission shift quality and/or using any special additives in the transmission.
Page 315 SERVICING AND MAINTENANCE After service is done, secure the cover with its two 1 — Fuse Element WARNING! locks. 2 — Blade Fuse with a good/functional fuse If a general protection fuse for safety systems  element CAUTION! (air bag system, braking system), power unit 3 —...
Page 316 SERVICING AND MAINTENANCE Power Distribution Center Location Cavity Cartridge Fuse Blade Fuse Description *If Equipped – – Not Populated – 25 Amp Clear Ignition Coil / Fuel Injector – – Not Populated...
Page 317 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped – 25 Amp Clear Amplifier / Active Noise Control * – – Not Populated – – Not Populated – 5 Amp Tan Battery Sensor (IBS) – 10 Amp Red ECM (S) * –...
Page 318 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped Diagnostic Port / USB+(IP) / Video – 10 Amp Red USB Port / Overhead DVD Player (Aftermarket) – – Not Populated – 15 Amp Blue Media HUB / Power Lumbar * –...
Page 319 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped 30 Amp Pink – Passenger Door Module – – Not Populated 25 Amp Clear – RR Sliding Door Module-LT * 25 Amp Clear – RR Door Module-RT * 30 Amp Pink –...
Page 320 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped – 20 Amp Yellow Trailer Tow Left Stop/Turn * – 15 Amp Blue RT HID Headlamp * – – Not Populated – 15 Amp Blue Cluster Haptic Lane Feedback Module (HALF) / –...
Page 321 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped – 15 Amp Blue TCM (ZF) / E-Shifter / Cluster – 10 Amp Red ICS / HVAC / SCCM/ EPB SW – – Not Populated – – Not Populated –...
Page 322 SERVICING AND MAINTENANCE Cavity Cartridge Fuse Blade Fuse Description *If Equipped Selectable Fuse Location – USB IP F95B – 10 Amp Red (Direct) B+ – 10 Amp Red Airbag – 10 Amp Red Airbag – 15 Amp Blue Left HID Headlamp * 30 Amp Pink –...
Page 323: Bulb Replacement
SERVICING AND MAINTENANCE EPLACEMENT Replacement Bulbs, Names, And Part Numbers In the instance a bulb needs to be replaced, this section includes bulb description and replacement part numbers. NOTE: Your vehicle is equipped with LED lamps. For replacement of LED lamps, see an authorized dealer. Interior Bulbs —...
Page 324 SERVICING AND MAINTENANCE Replacing Exterior Bulbs FRONT AND REAR SIDE MARKER LAMPS See below steps to replace: FRONT TURN SIGNAL LAMP 1. Remove the three fasteners from the inner See below steps to replace: wheel liner and carefully peel back liner for 1.
Page 325: Tires
SERVICING AND MAINTENANCE TIRES NOTE: Temporary spare tires are designed for tempo-  rary emergency use only. Temporary high pres- P (Passenger) — Metric tire sizing is based on US  sure compact spare tires have the letter “T” or AFETY NFORMATION design standards.
Page 326 SERVICING AND MAINTENANCE TIRE SIZING CHART EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 327 SERVICING AND MAINTENANCE EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: XL = Extra load (or reinforced) tire, or  LL = Light load tire or ...
Page 328 SERVICING AND MAINTENANCE EXAMPLE: 01 = Number representing the year in which the tire was manufactured (two digits) 01 means the year 2001  Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could ...
Page 329 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: NOTE: 1. Number of people that can be carried in the The proper cold tire inflation pressure is listed on vehicle. the driver’s side B-pillar or the rear edge of the driver's side door.
Page 330 SERVICING AND MAINTENANCE (4) The resulting figure equals the To determine the maximum loading conditions of Metric Example For Load Limit your vehicle, locate the statement “The combined available amount of cargo and luggage For example, if “XXX” amount equals 635 kg and weight of occupants and cargo should never load capacity.
Page 331 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 332: Tires - General Information
SERVICING AND MAINTENANCE — G Ride Comfort And Vehicle Stability IRES ENERAL NFORMATION WARNING! Proper tire inflation contributes to a comfortable Tire Pressure Unequal tire pressures from one side of the  ride. Overinflation produces a jarring and Proper tire inflation pressure is essential to the vehicle to the other can cause the vehicle to uncomfortable ride.
Page 333 SERVICING AND MAINTENANCE Inflation pressures specified on the placard are Tire Pressures For High Speed Operation Tire Repair always “cold tire inflation pressure”. Cold tire If your tire becomes damaged, it may be repaired if The manufacturer advocates driving at safe inflation pressure is defined as the tire pressure it meets the following criteria: speeds and within posted speed limits.
Page 334 SERVICING AND MAINTENANCE condition, please replace the TPM sensor as it is wear patterns will reduce tread life, resulting in not designed to be reused when driven under run the need for earlier tire replacement. flat mode 14 psi (96 kPa) condition. Distance driven.
Page 335: Tire Types
SERVICING AND MAINTENANCE Replacement Tires WARNING! CAUTION! The tires on your new vehicle provide a balance of Do not use a tire, wheel size, load rating, or Replacing original tires with tires of a different  many characteristics. They should be inspected speed rating other than that specified for your size may result in false speedometer and regularly for wear and correct cold tire inflation...
Page 336: Spare Tires - If Equipped
SERVICING AND MAINTENANCE Spare Tire Matching Original Equipped Tire Summer tires do not contain the all season (120 km/h) refer to original equipment or an designation or mountain/snowflake symbol on the authorized tire dealer for recommended safe And Wheel — If Equipped tire sidewall.
Page 337 SERVICING AND MAINTENANCE Do not install a wheel cover or attempt to mount a and reinstalled on your vehicle at the first needs to be replaced. Since it is not the same as conventional tire on the compact spare wheel, opportunity.
Page 338: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE NOTE: HEEL HEEL CAUTION! If you intend parking or storing your vehicle for an All wheels and wheel trim, especially aluminum extended period after cleaning the wheels with Avoid products or automatic car washes that use and chrome plated wheels, should be cleaned wheel cleaner, drive your vehicle and apply the acidic solutions or strong alkaline additives or regularly using mild (neutral Ph) soap and water to...
Page 339: Snow Traction Devices
SERVICING AND MAINTENANCE RACTION EVICES Use of traction devices require sufficient tire-to-body clearance. Due to limited clearance, the following snow traction devices are recommended. Follow these recommendations to guard against damage: Snow traction device must be of proper size for the tire, as recommended by the snow traction device manufacturer. ...
Page 340: Tire Rotation Recommendations
SERVICING AND MAINTENANCE The suggested rotation method is the “forward WARNING! CAUTION! cross” shown in the following diagram. This rotation pattern does not apply to some directional Using tires of different size and type (M+S, Do not drive for a prolonged period on dry ...
Page 341: Treadwear
SERVICING AND MAINTENANCE All passenger vehicle tires must conform concrete. A tire marked C may have poor on the laboratory test wheel, than the to Federal safety requirements in traction performance. minimum required by law. addition to these grades. WARNING! WARNING! READWEAR The traction grade assigned to this tire is based...
Page 342: Bodywork
SERVICING AND MAINTENANCE BODYWORK protect your paint finish. Use precautions to not NDERBODY AINTENANCE scratch the paint. Cleaning Headlights ROTECTION TMOSPHERIC Avoid using abrasive compounds and power  Your vehicle is equipped with plastic headlights buffing that may diminish the gloss or thin out GENTS and fog lights that are lighter and less susceptible the paint finish.
Page 343: Interiors
SERVICING AND MAINTENANCE If you carry special cargo such as chemicals, Seat Belt Maintenance LASTIC OATED ARTS  fertilizers, de-icer salt, etc., be sure that such Do not bleach, dye or clean the belts with chemical Use Mopar® Total Clean to clean vinyl upholstery. materials are well packaged and sealed.
Page 344: Leather Surfaces
SERVICING AND MAINTENANCE NOTE: EATHER URFACES LASS URFACES If equipped with light colored leather, it tends to Mopar® Total Clean is specifically recommended All glass surfaces should be cleaned on a regular show any foreign material, dirt, and fabric dye for leather upholstery.
Page 345: Technical Specifications
TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER (VIN) BRAKE SYSTEM ORQUE PECIFICATIONS The VIN is on the left front corner of the instrument Your vehicle is equipped with dual hydraulic brake Lug Nut/Bolt **Lug Nut/ Lug Nut/Bolt panel and is visible from outside of the vehicle systems.
Page 346: Fuel Requirements
TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS Tighten the lug nuts/bolts in a star pattern until EFORMULATED ASOLINE each nut/bolt has been tightened twice. Ensure Many areas of the country require the use of While operating on gasoline with the required that the socket is fully engaged on the lug nut/bolt cleaner burning gasoline referred to as octane number, hearing a light knocking sound (do not insert it halfway).
Page 347: Do Not Use E-85 In Non-Flex Fuel
TECHNICAL SPECIFICATIONS CNG A LP F Problems that result from using gasoline YSTEM ATERIALS DDED containing more than 15% ethanol (E-15) or ODIFICATIONS Besides using unleaded gasoline with the proper gasoline containing methanol are not the octane rating, gasolines that contain detergents, responsibility of the manufacturer and may void or Modifications that allow the engine to run on corrosion and stability additives are...
Page 348: Fuel System Cautions
TECHNICAL SPECIFICATIONS YSTEM AUTIONS CAUTION! Follow these guidelines to maintain your vehicle’s performance: The use of leaded gasoline is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some ...
Page 349: Engine Fluids And Lubricants
TECHNICAL SPECIFICATIONS ENGINE FLUIDS AND LUBRICANTS Component Fluid, Lubricant, or Genuine Part We recommend you use Mopar® Antifreeze/Coolant 10 Year/150,000 Mile Engine Coolant (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032. We recommend you use Mopar®...
Page 350: Chassis Fluids And Lubricants
TECHNICAL SPECIFICATIONS CHASSIS FLUIDS AND LUBRICANTS Component Fluid, Lubricant, or Genuine Part Use only Mopar® ZF 8 & 9 Speed ATF Automatic Transmission Fluid, or equivalent. Automatic Transmission Failure to use the correct fluid may affect the function or performance of your transmission.
Page 351: Customer Assistance
CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE IF YOU NEED ASSISTANCE Authorized dealer name  Vehicle Identification Number (VIN)  FOR YOUR VEHICLE FCA US LLC and its authorized dealers are vitally Vehicle delivery date and mileage  interested in your satisfaction. We want you to be happy with our products and services.
Page 352 CUSTOMER ASSISTANCE US V UERTO IRGIN SLANDS ERVICE ONTRACT WARNING! FCA Caribbean LLC You may have purchased a service contract for a Engine exhaust (internal combustion engines vehicle to help protect you from the high cost of P.O. Box 191857 only), some of its constituents, and certain unexpected repairs after FCA US LLC's New Vehicle vehicle components contain, or emit, chemicals...
Page 353 CUSTOMER ASSISTANCE MOPAR® PARTS PUBLICATION ORDER FORMS To contact NHTSA, you may call the Vehicle Safety Hotline toll free at Mopar® original equipment parts & accessories To order the following manuals, you may use either 1-888-327-4236 (TTY: and factory filled fluids are available from an the website or the phone numbers listed below.
Page 354 CUSTOMER ASSISTANCE La operación de este equipo está sujeta a las Owner's Manuals 1. This device may not cause harmful interference, and siguientes dos condiciones: These Owner's Manuals have been prepared with the assistance of service and engineering 2. This device must accept any interference 1.
Page 355 INDEX ........116 ........ 119 Air Bag Light Anti-Lock Warning Light .........343 ..........217 About Your Brakes Air Cleaner, Engine (Engine Air Cleaner Assist, Hill Start ............301 ............84 Adaptive Cruise Control (ACC) (Cruise Filter) Audio Jack ..........141 ......302 ........
Page 356 .. 254 Caps, Filler Lower Anchors And Tethers For Children ..........163 ............167 ..252 Back-Up Camera Fuel Older Children And Child Restraints ..........116 ..........298 ........254 Battery Oil (Engine) Seating Positions .......116 ..... 310 ....264 Charging System Light Radiator (Coolant Pressure) Using The Top Tether Anchorage ..........286...
Page 357 Cruise Control (Speed Control) ......142 Electric Parking Brake ........130 Oil Synthetic ..........301 Cruise Light ......... 122 Electric Remote Mirrors ........57 Overheating ..........289 Customer Assistance ........349 Electronic Stability Control (ESC) ....215 Starting ............. 126 Cybersecurity ..........179 Electronic Throttle Control Warning Light ..
Page 358 ...........348 ......169 Fluid, Brake Gross Vehicle Weight Rating Indicator Lights ..........63 ............168 ............123 Fog Lights GVWR Blue ....41 ............122 Fold In Floor (Stow ‘n Go) Seating Green ..........32 ............123 Fold-Flat Seats White ......223 ............
Page 359 Key Fob Programming (Remote Keyless Dimmer Switch, Headlight ......63 Service Automatic Emergency Braking ..121 Entry) ............... 16 Electric Power Steering Fault ....117 Service AWD ..........121 Keyless Enter 'n Go™ ........24 Electronic Park Brake ....... 119 Service LaneSense ........
Page 360 Manual ..........289 ......130 ............. 340 Park Release New Vehicle Break-In Period Paint Care ............351 ..........130 Service Parking Brake ........66 ......157 Map/Reading Lights ParkSense Active Park Assist ........322 ........229 ....... 151 Marker Lights, Side Occupant Restraints ParkSense System, Rear ............
Page 361 Reporting Safety Defects ......351 Pregnant Women ........236 Radial Ply Tires ..........331 Restraints, Child ........... 251 Pretensioners ........... 236 Radiator Cap (Coolant Pressure Cap) ....310 Restraints, Head ..........51 Rear Seat ..........230 Radio Operation ..........212 Roof Luggage Rack ........102 Reminder ..........
Page 362 ......56 ............. 203 ........330 Side View Mirror Adjustment Streaming Inflation Pressure ......63 ..........290 ..........273 Signals, Turn Stuck, Freeing Jacking ............ 64 ........... 90 ..........332 SmartBeams Sun Roof Life Of Tires ......337 .........81 ........... 327 Snow Chains (Tire Chains) Sunglasses Storage Load Capacity...
Page 363 Trailer Towing ..........169 Window Fogging ..........80 Hitches ............170 Vacuum ............97 Windows ............88 Minimum Requirements ......173 Stow ‘n Vac ..........97 Power ............88 Tips ............175 Vanity Mirrors ..........56 Windshield Defroster ........267 Trailer And Tongue Weight ......173 Vehicle Identification Number (VIN) ....343 Windshield Washers ......
Page 367 It is always the driver’s responsibility to comply with all local laws. This Owner’s Manual has been prepared to help you get acquainted with your new Chrysler brand vehicle and to provide a convenient reference source for common questions.
Page 368 ©2021 FCA US LLC. All Rights Reserved. Tous droits réservés. Chrysler is a registered trademark of FCA US LLC or FCA Canada Inc., used under license. Chrysler est une marque First Edition déposée de FCA US LLC ou FCA Canada Inc., utilisée sous le permis. App Store is a registered trademark of Apple Inc. Google Play Store is a registered trademark of Google.

Chrysler Pacifica 2022 Owner's Manual

Quick Links

Related Manuals for Chrysler Pacifica 2022

Summary of Contents for Chrysler Pacifica 2022