Earliest Version Software Requirements for the PC ... 25 Configuring with Crestron SystemBuilder ... 25 Configuring with SIMPL Windows ... 25 Example Program ... 27 Adjusting the QM-FTCC Microphone Inputs ... 28 Uploading and Upgrading... 31 Establishing Communication... 31 Programs and Firmware ... 31 Program Checks ...
Crestron QM-FTCC QuickMedia™ FlipTop Computer Center: QM-FTCC Introduction The QM-FTCC FlipTop Computer Center is part of the Crestron MediaManager™ line of network devices, room control systems and signal routing solutions. It is available in six different models. Models The international models accommodate a wide variety of international AC adaptors.
Page 6
AC power receptacle. Integrated Keypad (optional) The QM-FTCC can be ordered with or without a keypad. This customizable keypad provides 10 to 20 programmable pushbuttons for control of AV, lighting and other functions. All button caps are engravable and include LED feedback indicators. Two LED bar graphs are also provided to display level settings and other parameters.
Page 7
The Cresnet bus is a simple, yet flexible 4-wire network that provides rock-solid bidirectional communication and power for up to 252 Cresnet devices. Operations & Installation Guide – DOC. 6313B QuickMedia™ FlipTop Computer Center ® QuickMedia™ FlipTop Computer Center: QM-FTCC • 3...
QuickMedia™ FlipTop Computer Center Internal Block Diagram The following diagram represents the interfacing abilities of the QM-FTCC. This Cresnet device uses QuickMedia technology to facilitate simplified connection of audio, video and computer equipment. All media and control signals are routed via a single QuickMedia cable for easy installation.
Crestron QM-FTCC Specifications Specifications for the QM-FTCC are listed in the following table. QM-FTCC Specifications (Continued on following page) Operations & Installation Guide – DOC. 6313B QuickMedia™ FlipTop Computer Center SPECIFICATION Video Signal Types RGB Formats Video/HDTV Formats Gain Maximum Resolution...
Page 10
Crestron Authorized Independent Programmers (CAIP) only. New users may be required to register to obtain access to certain areas of the site (including the FTP site). 6 • QuickMedia™ FlipTop Computer Center: QM-FTCC SPECIFICATION Weight (Domestic Models) Weight (International Models)
Page 15
Input impedance: 75 ohms Pin 15 Pin 6 H/V sync impedance: 1k ohms Maximum input level: 1 V Maximum H/V sync level 5 V Signal detection on H, Y and G QuickMedia™ FlipTop Computer Center: QM-FTCC • 11 DESCRIPTION input B, YP...
Page 16
QuickMedia™ FlipTop Computer Center Connectors, Controls & Indicators (Continued) (Continued on following page) 12 • QuickMedia™ FlipTop Computer Center: QM-FTCC CONNECTORS CONTROLS & INDICATORS (1) 8-pin RJ-45 female, Ethernet LAN pass through jack for connection to Ethernet, providing local area network or Web access...
Page 17
QM transmitter (origination point) and receiver (endpoint) is 450 feet (137 meters) and 22 ns; a maximum of two QM midpoint devices may QuickMedia™ FlipTop Computer Center: QM-FTCC • 13 DESCRIPTION...
14 • QuickMedia™ FlipTop Computer Center: QM-FTCC be inserted in a given QM signal path (exceptions apply, refer to each respective product manual for full details).
Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators). • For larger networks, use a Cresnet Hub/Repeater (CNXHUB) to maintain signal quality. CresCAT-QM Cable QuickMedia™ FlipTop Computer Center: QM-FTCC • 15...
QM-WMC Identity Code The Net ID of the QM-FTCC has been factory set to 1A. The Net IDs of multiple QM-FTCC devices in the same system must be unique. Net IDs are changed from a personal computer (PC) via Crestron Toolbox™ (refer to “Establishing Communication”...
“Cable Management Plate” which starts on page 18. Button Installation The QM-FTCC is shipped with ten large blank buttons. You can order a variety of button kits (sold separately) for a total of 20 engraved or blank buttons.
Page 22
Button Installation Cable Management Plate The QM-FTCC is shipped with a blank bottom plate. A cable management plate is available to provide a pullout cable solution for the computer input and LAN pass through cables. The kit contains two 6-foot cables (computer and computer audio).
Page 23
7. Connect the cables to the appropriate connector on the front of the QM-FTCC. 8. The cables may be secured to the bottom bar using the supplied tie wraps. QuickMedia™ FlipTop Computer Center: QM-FTCC • 19 Bushings Cable Support Plate...
Page 24
FlipTop box. Mounting to Surface The QM-FTCC is designed to mount in a horizontal surface, such as a desk top, lectern or podium. The following diagram illustrates the required opening size to accommodate the QM-FTCC. A cutout template (40071 or 40073) is included.
Page 25
Crestron QM-FTCC Mounting Parts Supplied with the QM-FTCC A Phillips screwdriver is required to mount the QM-FTCC to a surface. Mounting Bracket Screw Locations NOTE: Do not over-tighten the #10 screws as this may damage the surface and/or the unit.
Page 26
NOTE: Be careful not to press the buttons while closing the FlipTop, even though the buttons are disabled when the FlipTop begins to close and all pressed buttons are released. 22 • QuickMedia™ FlipTop Computer Center: QM-FTCC Crestron QM-FTCC Operations & Installation Guide – DOC. 6313B...
Refer to “Network Wiring” on page 15 before attaching the 4-position terminal block connector. Apply power after all connections have been made. When making connections to the QM-FTCC, consider the following: Hardware Connections for the QM-FTCC (Top) Operations & Installation Guide – DOC. 6313B QuickMedia™...
Page 28
Ground Wire Connections Proper grounding is required. Connect the ground from the QM transmitter (QM-FTCC) to earth ground. Connect the Cresnet shield at the QM-RMCRX-BA to the chassis ground provided on the QM-RMCRX-BA. The QM-RMCRX-BA chassis must also be connected to an earth ground (building steel). Refer to the following grounding diagram.
SystemBuilder from the Crestron website and examine the extensive help file. Configuring with SIMPL Windows NOTE: While SIMPL Windows can be used to program the QM-FTCC, it is recommended to use SystemBuilder for configuring a QuickMedia system. SIMPL Windows is Crestron’s premier software for programming Crestron control systems.
Page 30
The system tree of the control system displays the device in the appropriate slot with a default Net as shown in the following illustration. • Additional QM-FTCC devices are assigned different Net ID numbers as they are added. • If necessary, double click a device to open the “Device Settings” window and change the Net ID, as shown in the following figure.
View. Each signal in the symbol is described in the SIMPL Windows help file (F1). The buttons module is built into slot 03 of the QM-FTCC (refer to “C2Net Device, Slot 9” on page 26). It consists of a keypad that provides 10 to 20 buttons with LED indicators, and two bar graphs.
QuickMedia™ FlipTop Computer Center Adjusting the QM-FTCC Microphone Inputs Once a QM-FTCC is installed and configured, settings for gain, gating level, attack time and decay time should be set using the SystemBuilder finish tab. NOTE: Crestron recommends that you use the latest software to take advantage of the most recently released features.
Page 33
Reached Setting Microphone Gain The QM-FTCC provides variable gain for the microphone inputs. The following procedure is used to set the optimal gain for a microphone input. Use the Realtime Mode in SystemBuilder to control phantom power, gain and gate settings and to monitor the gate, normal and clip level indicators.
Page 34
QuickMedia™ FlipTop Computer Center Setting the Gating Level The QM-FTCC provides an input level gating function that will mute a microphone signal when the input sound level is below a user-set threshold. This function can be enabled or disabled via software commands.
Use the Address Book in Crestron Toolbox to create an entry for the QM-FTCC using the expected communication protocol (Indirect). Select the Cresnet ID of the QM-FTCC and the address book entry of the control system that is connected to the QM-FTCC.
Using Crestron Toolbox, display the network device tree (Tools | Network Device Tree) to show all network devices connected to the control system. Right-click on the QM-FTCC to display actions that can be performed on the QM-FTCC. 32 • QuickMedia™ FlipTop Computer Center: QM-FTCC •...
Grounding problem. and/or mic. Intermittent or Incorrect peak setting. no audio/mic output. QuickMedia™ FlipTop Computer Center: QM-FTCC • 33 CORRECTIVE ACTION Verify the Net ID in Toolbox. Verify SIMPL Windows program for setting Net ID. Assign a different Net ID.
When calculating the length of wire for a particular Cresnet run, the wire gauge and the Cresnet power usage of each network unit to be connected must be taken into consideration. Use Crestron Certified Wire only. If Cresnet units are to be daisy- 34 • QuickMedia™ FlipTop Computer Center: QM-FTCC TROUBLE POSSIBLE CAUSE(S)
1.6 Ohms (Cresnet HP: 12 AWG (4 MM )) P = Cresnet power usage of entire run (or chain) DOCUMENT TITLE 2-Series Control Systems Reference Guide MediaManager Applications Guide QM-RMCRX-BA QuickMedia Receiver/Processor QuickMedia™ FlipTop Computer Center: QM-FTCC • 35...
Future Updates As Crestron improves functions, adds new features and extends the capabilities of the QM-FTCC, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision.
NOTE: If auto compensation is used in your QM system, all QM devices must use it. If it is not used in your QM system, it must not be used for any of the QM devices. 38 • QuickMedia™ FlipTop Computer Center: QM-FTCC Crestron QM-FTCC...
Page 43
QM cable. The QM-AE is a self-peaking receiver, so peaking is not required. Operations & Installation Guide – DOC. 6313B QuickMedia™ FlipTop Computer Center • QM-RMCRX • QM-MD7x2 • QM-MD5x1 • TPMC-15-QM • TPMC-17-QM QuickMedia™ FlipTop Computer Center: QM-FTCC • 39...
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation. 42 • QuickMedia™ FlipTop Computer Center: QM-FTCC Crestron QM-FTCC...
Page 47
Crestron QM-FTCC Operations & Installation Guide – DOC. 6313B QuickMedia™ FlipTop Computer Center This page is intentionally left blank. This page is intentionally left blank. This page is intentionally left blank. QuickMedia™ FlipTop Computer Center: QM-FTCC • 43...