Subscribe to Our Youtube Channel
Related Manuals for Crestron QM-FTCC-TPS4
Summary of Contents for Crestron QM-FTCC-TPS4
- Page 1 Crestron QM-FTCC-TPS4 FlipTop Touchpanel Computer Center Operations & Installation Guide...
- Page 2 This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc.
-
Page 3: Table Of Contents
Earliest Version Software Requirements for the PC...25 Programming with SystemBuilder ...25 Programming with SIMPL Windows...26 Example Program...28 Programming with VT Pro-e...28 Adjusting the QM-FTCC-TPS4 Microphone Inputs ...29 Communication Settings ...32 Uploading a SIMPL Windows Program ...35 Firmware Upgrade ...37 Further Inquiries...41 Future Updates ...41... -
Page 5: Fliptop Touchpanel Computer Center: Qm-Ftcc-Tps4
Functional Summary * As an option, a custom-engraved bezel can be designed and obtained by using the Crestron Engraver software. Version 2.4 and Crestron Database 17.4 or later are available from the Crestron website (www.crestron.com). - Page 6 To prevent any inadvertent screen presses, the QM-FTCC-TPS4 disengages the touchpanel whenever the lid is not fully opened. The QM-FTCC-TPS4 mounts flush to any tabletop, concealing all cables and connectors, providing a clean professional appearance to any conference room or classroom. Complete MediaManager systems can be configured easily for a variety of applications using Crestron SystemBuilder™...
-
Page 7: Quickmedia Transport System
CresCAT-QM cable, simplifying installations. Routing CresCAT-QM cable is less expensive and much simpler than routing multi- colored, multi-conductor coax cable. All Crestron products using the QM transport system are capable of sending and receiving QM signals via CresCAT-QM cable. - Page 8 The total accumulated skew from QM transmitter to QM receiver must not exceed 22 ns. Crestron recommends a cable with a rating of less than or equal to 22 ns over its entire length. For example, if using a cable with a rating of 22 ns/100 meters (100...
-
Page 9: Specifications
Specifications for the QM-FTCC-TPS4 are given in the following table. QM-FTCC-TPS4 Specifications 1. The latest software versions can be obtained from the Crestron website. Refer to the NOTE following 2. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product Operations &... -
Page 10: Physical Description
FlipTop Touchpanel Computer Center NOTE: Crestron software and any files on the website are for Authorized Crestron dealers and Crestron Authorized Independent Programmers (CAIP) only. New users may be required to register to obtain access to certain areas of the site (including the FTP site). - Page 11 (18.22 cm) QM-FTCC-TPS4 Bottom View Operations & Installation Guide – DOC. 6393 FlipTop Touchpanel Computer Center Front View QMI-FTCC-TPS-4 Physical Dimensions QMI-FTCC-TPS4 Bottom View FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 7 Front View 7.51 in (19.08 cm) 8.41 in (21.35 cm)
- Page 12 FlipTop Touchpanel Computer Center QM-FTCC-TPS4 Physical Dimensions QM-FTCC-TPS4 Physical Dimensions 5.51 in (14.0 cm) 6.05 in (15.37 cm) 8 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 Back View QMI-FTCC-TPS4 Physical Dimensions 2.75 in (6.99 cm) 0.09 in (0.23 cm) 4.66 in (11.84 cm)
- Page 13 Gate level (threshold): 0 to 100% • Attack: 1 to 100 ms • Decay (release): 1 to 5000 ms • Analog to Digital conversion: 24-bit, 48 kHz • @ 10 kΩ). FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 9 maximum maximum...
- Page 14 2 to COMPUTER support RGsB and Y, P connector pin-assignments. RGB DB15HD Pin Assignments 10 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 RJ-45 PIN WIRE COLORS NUMBER (EIA 568B) WHITE/ORANGE...
- Page 15 SETUP LED and Pushbutton (Underside) The QuickMedia module is Touch-Settable ID-ready. A SETUP pushbutton is located on the bottom side of the QM-FTCC-TPS4. The SETUP pushbutton and its associated LED are used for setting the QuickMedia module’s network ID during the initial configuration of a Cresnet system or when the device is being added/replaced.
-
Page 16: Industry Compliance
FlipTop Touchpanel Computer Center Industry Compliance As of the date of manufacture, the QM-FTCC-TPS4 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to... -
Page 17: Qm Network Wiring
QM-FTCC-TPS4 QM-FTCC-TPS4 Crestron Toolbox The Crestron Toolbox (replacement for Crestron Viewport, you may continue to use Viewport if desired) is a broad-based software package that accomplishes multiple system tasks, primarily using an RS-232 or TCP/IP connection between a PC and one or more Crestron control systems. - Page 18 Settings” on page 27 for details of the SIMPL Windows procedure. The Net ID of the QM module of the QM-FTCC-TPS4 has been factory set to 1A. The Net ID of the TPS4 touchpanel of the QM-FTCC-TPS4 has been factory set to 03.
-
Page 19: Installation
Installing Engraved Bezel Use the Crestron Engraver software package to obtain a custom-engraved bezel for the QM-FTCC-TPS4. Install the replacement bezel as follows. Operations & Installation Guide – DOC. 6393... - Page 20 Engraved Bezel Installation Cable Management Plate The QM-FTCC-TPS4 is shipped with a cable management plate and associated parts to provide a pullout cable solution for the computer input and LAN passthrough cables. The parts include a three-hole plate, grommets, and two 6-foot cables (computer and computer audio).
- Page 21 Crestron QM-FTCC-TPS4 Tools Required The cable support plate must be installed before mounting the QM-FTCC-TPS4 to a surface. The cables are looped through the cable support plate. Cable Management Plate Installation Operations & Installation Guide – DOC. 6393 FlipTop Touchpanel Computer Center Phillips screwdriver •...
- Page 22 FlipTop box. Mounting to Surface The QM-FTCC-TPS4 is designed to mount in a horizontal surface, such as a desk top, lectern, or podium. The following diagram illustrates the required opening size to accommodate the QM-FTCC-TPS4. A cutout template (4007478 or 4007780) is included.
- Page 23 Crestron QM-FTCC-TPS4 NOTE: Before inserting the QM-FTCC-TPS4 in the mounting hole, ensure that all required cables have been installed. Mounting Parts Supplied with the QM-FTCC-TPS4 Mounting Bracket Screw Locations NOTE: Do not over-tighten the #10 screws as this may damage the surface and/or the unit.
-
Page 24: Hardware Hookup
The ratings on the connecting unit's supply input should be considered to prevent overloading the wiring. 20 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 Crestron QM-FTCC-TPS4 Operations & Installation Guide - DOC. 6393... -
Page 25: Ground Wire Connections
QM-RMCRX-BA chassis must also be connected to an earth ground (building steel). Refer to the following grounding diagram. Ground Wire Connections NOTE: Do not connect the shield to earth ground at the QM-FTCC-TPS4. Operations & Installation Guide – DOC. 6393 FlipTop Touchpanel Computer Center... -
Page 26: Configuring The Touchpanel
NOTE: The touchscreen responds to both finger and stylus commands. Since the screen is small, Crestron recommends that a stylus (not supplied) be used to ensure the accuracy of commands. Use a stylus that will not damage the surface of the screen. -
Page 27: Screen Settings
The bias setting is best when the lines are crisp and dark and the white area around them is bright. Press Return to save the settings and return to the SETUP MENU. FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 23... -
Page 28: Timeout Settings
Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account. You can create a program that allows you to include the QM-FTCC-TPS4 in a Crestron control system. The program output of Crestron SystemBuilder is a SIMPL Windows program with much of the functionality encapsulated in macros and templates. -
Page 29: Earliest Version Software Requirements For The Pc
Crestron QM-FTCC-TPS4 Earliest Version Software Requirements for the PC NOTE: Crestron recommends that you use the latest software to take advantage of the most recently released features. The latest software is available from the Crestron website. The following are the earliest useable software version requirements for the PC:... -
Page 30: Programming With Simpl Windows
System Views. The QM-RMCRX-BA with its associated communication ports is displayed in the System Views upper pane. NOTE: Crestron software and any files on the website are for Authorized Crestron dealers and Crestron Authorized Independent Programmers (CAIP) only. New users may be required to register to obtain access to certain areas of the site (including the FTP site). -
Page 31: C2Net-Device Slot In Configuration Manager
Net ID. Supported devices include network control modules, lighting modules and a variety of Crestron wired touchpanels. The QM-FTCC-TPS4 is actually two devices in a single housing, so to incorporate a QM-FTCC-TPS4 into the system, you need to drag both the touchpanel (TPS4) and the QuickMedia module (QM-FTCC) into System Views individually. -
Page 32: Example Program
NOTE: This procedure sets the Net ID for the QM-FTCC-TPS and the TPS4 in the program only. It does not automatically set the Net ID for the QM-FTCC-TPS4 hardware. SIMPL Windows automatically changes Net ID values of a device added to a program if a duplicate device or a device with the same Net ID already exists in the program. -
Page 33: Adjusting The Qm-Ftcc-Tps4 Microphone Inputs
PC. The PC may be disconnected from the control system or panel except during reprogramming. When you start the VT Pro-e project for this product, select QM-FTCC-TPS4 as the panel type. - Page 34 Visual Representation of Gating Level, Clipping Level, Attack Time, and Decay Time Setting Microphone Gain The QM-FTCC-TPS4 provides variable gain on the microphone inputs. The following procedure is used to set the optimal gain for a microphone input. Use the Realtime Mode in SystemBuilder to control phantom power, gain and gate settings, and to monitor the gate, normal, and clip level indicators.
-
Page 35: Setting The Gating Level
Setting the Gating Level The QM-FTCC-TPS4 provides an input level gating function that will mute a microphone signal when the input sound level is below a user-set threshold. This function can be enabled or disabled via software commands. -
Page 36: Uploading And Upgrading
New users are required to register to obtain access to this site. Assuming a PC is properly connected to the entire system, Crestron programming software allows the programmer to upload programs and projects to the system and touchpanel and firmware to the wall plates after their development. - Page 37 QM-RMCRX-BA QuickMedia Receiver/Processor Operations Guide (Doc. 6332) or the Crestron e-Control Reference Guide (Doc. 6052). These documents are available from the Crestron website. Refer to the following figure for a typical connection diagram when uploading files.
- Page 38 Hardware handshaking (RTS/CTS) enabled. • Software handshaking (XON/XOFF) not enabled. 2. After setting the correct parameters, click OK to return to the Crestron Toolbox main window. 3. Select Tools | System Info. If the connection is successful, the System Info window displays the processor and device information.
-
Page 39: Uploading A Simpl Windows Program
3. Select Functions | SIMPL Program…The “SIMPL Program” window appears, as shown in the following figure, and permits you to browse for a compiled program file (.spz), and allows you to upload to internal flash. FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 35... - Page 40 FlipTop Touchpanel Computer Center 36 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 “SIMPL Program” Window 4. Browse for the appropriate .spz file in the “Open” window, and click Open. “Open” Window 5. When the “SIMPL Program” window reappears, click Send. 6. To verify that the program has been transferred successfully, select Functions | SIMPL Program.
-
Page 41: Firmware Upgrade
Toolbox will automatically extract the file(s) for you. NOTE: A firmware upgrade file for the QM module of the QM-FTCC-TPS4 has the extension .upg. The following is a typical firmware upgrade file name for the QM- module. - Page 42 FlipTop Touchpanel Computer Center “Firmware” Window Locate Firmware via the “Open” Window 38 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 6. Click Browse to display the Open window to locate the desired firmware (.zip) file. 7. Highlight the desired. zip file and click Open to select the file and return to the “Firmware”...
- Page 43 Operations & Installation Guide – DOC. 6393 FlipTop Touchpanel Computer Center 8. When the transfer is complete, the “Firmware” window reopens indicating the new firmware version. Click Close after the firmware has been transferred. FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 39...
-
Page 44: Problem Solving
FlipTop Touchpanel Computer Center Problem Solving The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. QM-FTCC-TPS4 Troubleshooting Continued on the following page 40 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4... -
Page 45: Further Inquiries
For assistance in your local time zone, refer to the Crestron website (http://www.crestron.com/) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. -
Page 46: Appendix A: International Receptacles
UK, 250V, 13A, BLK 6003291 PWR-FR-B POWER RECEPTACLE, FRENCH, 250V, 16A, 42 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 Crestron QM-FTCC-TPS4 COUNTRIES Australia, Fiji, New Zealand, Papua New Guinea Austria, Azerbaijan, Belarus, Bosnia and Herzegovina, Brunei, Bulgaria, Burundi, Cape Verde, Chad, Croatia, Czech Republic, Egypt, Eritrea,... -
Page 47: Appendix B: Quickmedia Installation And Compensation
NOTE: If auto compensation is used in your QM system, all QM devices must use it. If it is not used in your QM system, it must not be used for any of the QM devices. Operations & Installation Guide – DOC. 6393 FlipTop Touchpanel Computer Center FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 43... - Page 48 FlipTop Touchpanel Computer Center Auto Compensation with a Self-Peaking Receiver Crestron's innovative self-peaking audio circuit eliminates the need to peak the audio signal. Without self-peaking the same peak and boost values are applied equally to the video and audio signals. When these signals travel the same path, this arrangement is satisfactory.
-
Page 49: Compatibility Charts
Auto Compensation with Audio Breakaway MD8x8 TRANSMITTERS MD4x2 MD7x2 MD5x1 Operations & Installation Guide – DOC. 6393 FlipTop Touchpanel Computer Center QM RECEIVERS RMCRX RXA* MD7x2 RMCRX- QM RECEIVERS RMCRX RMCRX- RXA* MD7x2 FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 • 45 TPMC MD5x1 TPMC MD5x1... - Page 50 Manual Compensation without Audio Breakaway MD8x8 TRANSMITTERS MD4x2 MD7x2 MD5x1 Manual Compensation with Audio Breakaway MD8x8 TRANSMITTERS MD4x2 MD7x2 MD5x1 46 • FlipTop Touchpanel Computer Center: QM-FTCC-TPS4 QM RECEIVERS RMCRX RMCRX- RXA* MD7x2 QM RECEIVERS RMCRX RMCRX- RXA* MD7x2 Crestron QM-FTCC-TPS4...
-
Page 51: Return And Warranty Policies
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. - Page 52 Crestron Electronics, Inc. Operations & Installation Guide – DOC. 6393 15 Volvo Drive Rockleigh, NJ 07647 (2013361) Tel: 888.CRESTRON 11.05 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
Need help?
Do you have a question about the QM-FTCC-TPS4 and is the answer not in the manual?
Questions and answers