Summary of Contents for Assa Abloy SARGENT BL7300 Series
Page 1
Installation Instructions Multi-Point Lock FM7300 Series and BL7300 Series Important The latches, rods, and cassette are pre-installed. This product must be installed by a factory trained technician. WARNING This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Package Contents Part Number Description 82-5342 Multipoint cassette 82-5345 Trim mounting screw pack 82-5346 Top/bottom case mounting screw pack 82-5347 Top strike pack 82-5348 Bottom strike pack 82-5349 Mortise mounting/reinforcement pack 82-5350 Center strike pack 82-5351...
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Tools Required Tape measure Hammer Flashlight 1/8" Allen 3/32" Allen 5/32" Allen (supplied) (supplied) Drill 1/8" Masonry #3 Phillips Slotted #1, #2, #3 Chisel 3/8" drill bit screwdriver Phillips head Anchor set screwdrivers Tools Required for Electronic Access Control (EAC) Shield #29 Drill bit...
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation Check Door Verify the door is: • Correct size and hand for opening. • Correctly prepared to Template 4740. Outswing Door IMPORTANT Shown If measurement is incorrect, DO NOT PROCEED WITH INSTALLATION.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Install Center Strike into Door Frame • Install two (2) ¼-20 socket cap flat head screws. (Figure 3) Remove Retractor Inserts Figure 3 WARNING The door now has the ability to latch. (Figure 4) Figure 4 Check Latches (uninstalled)
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Install Bottom Strike • Close the door and mark the location of the bottom bolt. 3/8" MAX Bottom of door to floor. Figure 7 • Open the door and place the strike over the bottom bolt location. Mark the location of the bottom strike pocket and hole locations.
Page 9
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Install Bottom Strike (cont .) Flush Mount (Figure 9) Surface Mount (Figure 12) Chisel the bottom strike pocket Mortise the strike into the floor 1/4" deep. 1" deep to ensure the bolt has full projection.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Top and Bottom Latch Adjustment TOP OF DOOR • With the door hung, measure the clearance 1/16" Bolt to strike clearance. between the top and bottom bolts and strikes. (Figure 15) BOTTOM OF DOOR Note:...
Page 11
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Top and Bottom Latch Adjustment (cont .) TOP OF DOOR Using the supplied 3/32" Allen wrench, rotate the top 1/16" Bolt to strike clearance. or bottom worm gears according to the directions below (Figure 19).
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Final Mortise Lock and Trim Installation Follow the supplied mortise lock installation instructions for trim and other function related hardware. Electronic Access Control (EAC) Reader and Controller Installation Follow supplied EAC Installation Instructions (if applicable).
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Installation (cont .) Electronic Access Control (EAC) Shield (if applicable) • Install the EAC shield (provided) over the inside controller. (Figure 28) • Drill and tap the door for #8-32 machine screws (provided). IMPORTANT EAC shield MUST be centered on controller.
Page 15
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Optional Installation (cont .) Dogging Indicator Installation (cont .) • Using a #7 drill bit, drill two (2) holes completely through the door, making sure the drill remains square to the face of the door. (Figure 30) Figure 30 •...
Page 16
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Optional Installation (cont .) Dogging Indicator Installation (cont .) Install the indicator on the inside of the door using supplied 10-24 x 2" oval head screws. Make sure the control fingers grab the top rod pin as shown. (Figure 32) Side View Control Fingers Figure 32...
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum This addendum is to be used as a reference for pre-installed hardware (latches and cassette). The following steps are for ease of reference as they have been completed in advance by the door manufacturer.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum (cont .) Install Lockbody Cassette (LBC) LBC Gear Worm Gear • Using the supplied 3/32" Allen wrench, rotate both LBC worm gears to align slots in the LBC gears to the orientation shown. (Figure 36) Alignment is needed for proper installation of the...
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum (cont .) Feed Top Rod into Door • Orient the latch chassis as shown. Rotate the rod and rod guide so the rod guide tab faces up. Slide the rod assembly into the door. Make sure the rod guide remains in the correct orientation with the guide tab facing up.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum (cont .) Troubleshoot Latch Installation Misaligned Rod Guide Rod Guide • If the latch will not fully seat in the door, rod or rod guide is not aligned properly with LBC gear.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum (cont .) Secure Top Latch • Install four (4) 10-24 oval head screws on the face of the door. (Figure 44) Figure 44 • Install six (6) 1/4-20 flat head screws in the top edge of the door.
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum (cont .) Bottom Latch Installation REPEAT Steps 5e through 5k to install bottom latch. (Figure 47) Check Latch Figure 47 • Remove the bolt retainer clips from the top and bottom latch assemblies. (Figure 48) •...
Multi-Point Lock FM7300 Series and BL7300 Series Installation Instructions Addendum (cont .) Mortise Reinforcer and Mortise Lock Installation • Remove the two (2) #12-24x1" flat head LBC mounting screws that are securing the lockbody case in the door. (Figure 52) • Place mortise reinforcer into the door. •...
Page 24
SARGENT Manufacturing Company 100 Sargent Drive New Haven, CT 06511 USA 800-727-5477 www.sargentlock.com Founded in the early 1800s, SARGENT ® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications.