Table of Contents
Advertisement
Chapter
3
ITALTLALITI|
3-12 (E)
Preparations for Editing
: 2 times normal speed.
: 3 times normal speed.
PLAYER 1 MAX DT SPEED
SEtUP-18 | P1 SPEEd
Maximum DT playback speed of player 1.
PLAYER 2 MAX DT SPEED
SEtUP-19 | P2SPEEd
Maximum DT playback speed of player 2.
SWITCHER TYPE
SEtUP-20
|S tyPE
Select the type of your switcher.
If you select 1201, or change the selection
from 1201 to another switcher, this unit must
be powered off and on again before using the
selection.
unless SEtUP-25 (EDL MODE) is set to On.
For more information about the snapshot
AU3 SCP]
0/1/2/--./99: Crosspoint, in range from 0 to 99.
However, always 5 when using the BVS-
V1201 or BVS-A1201, regardless of the
2
3
2: 2 times normal speed.
3: 3 times normal speed.
500: DFS-500 series
3000: BVS-3000 series
1100: BVS-1100
G100: GVG 100
1201: BVS-V1201, BVS-A1201
corresponding to the AUX3 (ENTRY + FROM
TO) button in the source selection section.
AUX 3 MIXER CROSSPOINT
SEtUP-23
The crosspoint for the audio mixer
corresonding to the AUX3 (ENTRY + FROM
TO) button in the source selection section.
USE EXT MON
Whether to forcibly set the audio mixer's EXT
MON to ON.
control, see "Controlling the DFS-500
setting of this item.
Snapshot Function" (page 6-2(E))
AUX 3 SWITCHER CROSSPOINT
AU3ACP | 0/1/2/---/99: Crosspoint, in range from 0 to 99.
However, must be set to 1, 2, 3 or 4 when
using a mixer with a parallel interface.
A600 USE | OFF: Do not set to ON.
The crosspoint for the video switcher
On: Set to ON.
When using the VSP-A600, the EXT MON
connector ON/OFF switch cannot be set from
the control panel. Therefore, set this item to
On when monitoring recorder output through
the EXT MON connector.
EDL MODE
Whether or not to save the EDL in internal
memory (internal EDL mode). Note that all
data in internal EDL memory is cleared when
this item is set to external EDL mode.
AUTO EDL CLEAR
SEtUP-26 | Auto Clr
OFF: Disable overwriting.
In internal EDL mode, whether or not data can
On: Enable overwriting.
be overwritten when the EDL becomes full
(when edit 00 is saved). Overwriting begins by
clearing the first edit (01), and continues from
there toward the end of the list.
TIMECODE PRESET
SEtUP-27 | tc PrSEt
00H/01H/---/23H: Hour from 00 to 23.
Preset value of the recorder's time code
generator (hours digits).
TIME CODE OFFSET
Whether to begin recording 20 seconds or 60
seconds before the preset time.
MAXIMUM SHUTTLE SPEED
The playback speed in shuttle mode when the
search dial is rotated as far as possible.
Chapter 3 Preparations
EdL Cont | OFF: Use external EDL mode.
On: Use internal EDL mode.
SEtUP-29
tc OFSEt
| 20: 20 seconds
—60: 60 seconds
SEtUP-30
|SHtL SPd|
10: 10 times normal speed
16: 16 times normal speed
Advertisement
Table of Contents
