Related Manuals for Modular Closets MUDROOM
Summary of Contents for Modular Closets MUDROOM
- Page 1 1-844-969-4247 MUDROOM ASSEMBLY AND INSTALLATION INSTRUCTIONS...
-
Page 2: Parts List
ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM PARTS LIST Left Side Panel, Upper (Qty 1) Right Side Panel, Upper (Qty 1) Set Shelf, Upper (Qty 2) Adjustable Shelf, Upper (Qty 1) Left Side Panel, Bench (Qty 1) Right Side Panel, Bench (Qty 1) -
Page 3: Tools Required
ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM PARTS LIST Drawer Panel, Front (Qty 1) Drawer Panel, Rear Qty (1) Drawer Panel, Side (Qty 2) Drawer Front (Qty 1) Drawer Bottom (Qty 1) Drawer Slide (Qty 2) Shelf Slide (Qty 2) Drawer Handle (Qty 1) Euro Screw, 5/8"... - Page 4 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 2.1 Install one Cam Post (J) into each of the 6 holes on Bench Top Shelf (G). Tighten until Cam Posts are seated against Top Shelf. 3.1 Install one Cam Post (J) into each of the 10 holes on Bench Left Side Panel (E) and Bench Right Side Panel (F).
- Page 5 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 4.1 Assemble Bench Set Shelf (H), and two Cleats (I) onto Bench Right Side Panel (F) by sliding the Shelf and Cleats onto Cam Posts (J) on Right Side Panel. BE SURE dowel pins in Shelf and Cleats engage drilled holes in Right Side Panel, and all parts are pressed flush against Panel.
- Page 6 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM ARROW TOWARD CAM POST OPENING Insert Camlocks (K) in holes in Bench Set Shelf (H) and two Cleats (I) with arrow pointing toward Cam Post opening. Be sure Camlocks engage Cam Posts, and are fully seated in Shelf and Cleats.
- Page 7 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM J J J 8.1 Install one Cam Post (J) into each of the 7 holes on Upper Left Side Panel (A) and Upper Right Side Panel (B). Tighten until Cam Posts are seated against Side Panels.
- Page 8 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 9.1 Assemble Upper Set Shelves (C) and Cleats (I) onto Upper Right Side Panel (B) by sliding the Shelves and Cleats onto Cam Posts (J) on Right Side Panel. BE SURE dowel pins in Shelves and Cleats engage drilled holes in Right Side Panel, and all parts are pressed flush against Panel.
- Page 9 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 10.1 Install Upper Left Side Panel (A) onto assembled Set Shelf (C) and CleatS (I). BE SURE dowel pins in Shelves and Cleats engage drilled holes in Side Panel, and Side Panel is pressed flush against Shelves and Cleats.
- Page 10 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM ARROW TOWARD CAM POST OPENING 11.1 Insert Camlocks (K) in holes in Set Shelves (C) and Cleats (I) with arrow pointing toward Cam Post opening. Be sure Camlocks engage Cam Posts, and are fully seated in Shelf and Cleats.
- Page 11 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM Upper Side Panel BACK USE TO USE FOR ALIGN FLUSH OFFSET FRONT 12.1 Insert four Wood Dowels (M) into holes in edges of Upper Left Side Panel (A) and Upper Right Side Panel (B). Note: There are two pairs of holes in each Side Panel; one pair for flush alignment of the Upper Shelf and Bench, and one pair to offset the Upper Shelf when necessary to accomodate a baseboard.
-
Page 12: Installation
ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM PILOT HOLE PILOT HOLE STUD INSTALLATION 13.1 Determine the mounting location for the unit. 13.2 Using a stud finder, locate the studs to which the unit will be secured. Mark the stud location with a pencil. - Page 13 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 14.1 Secure two top Cleats (I) to stud using two 2.5" screws (N).
- Page 14 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM Installation of Adjustable Shelf (D) is optional. If desired, install Adjustable Shelf as follows: 15.1 Insert 4 Shelf Pins (L) into pin holes at the desired heights. 15.2 Rest Adjustable Shelf (D) on Shelf Pins (L).
- Page 15 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM TYPICAL HOOK INSTALLATION 16.1 Installation of Hooks (O, P) is optional. If desired, install Hooks at one or more of the following lodations: - Install one or two 3-Prong Hooks (O) on Upper Left Side Panel (A). (Dimples on the vertical centerline of the Side Panel show the recommended placement for the Hooks.)
- Page 16 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 17.1 Insert Wood Dowels (DD) into holes in ends of Front Drawer Panel (R) and Rear Drawer Panel (S). 18.1 Align Wood Dowels in Front Drawer Panel (R) and Rear Drawer Panel (S) with holes in one Side Drawer Panel...
- Page 17 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM NOTE: Be sure to install Drawer Bottom (V) with finished side facing up. 19.1 Align Drawer Bottom (V) with slots in Front Drawer Panel (R) and Rear Drawer Panel (S), then slide Drawer Bottom into assembled Drawer Panels until Drawer Bottom is seated against Side Drawer Panel (T).
- Page 18 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 21.1 Secure Side Drawer Panels (T) to Front Drawer Panel (R) and Rear Drawer Panel (S) using 1.0" Drawer Side Screws (BB). NOTE: Drawer Slides (W) and Shelf Slides (X) are shipped assembled. Lift Slide Release to separate Drawer Slide from Shelf Slide.
- Page 19 ASSEMBLY AND INSTALLATION INSTRUCTIONS VANITY, 19.5 NOTE: DO NOT overtighten Screws (BB) or surface of Drawer Front (M) may become dimpled. 23.1 Position Drawer Front (U) on assembled Drawer and secure to Front Drawer Panel (R) with 1.0" Screws (BB). 23.2 Install Drawer Handle (Y) on Drawer and secure with two 1.5"...
- Page 20 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 24.1 Position Shelf Slide (X) over pre-drilled holes in Base Side Panel, then secure with two 5/8" Screws (AA) at locations shown. 24.2 Repeat for second Shelf Slide (X). Tip: For best results, use a small level to ensure Shelf Slides (X) are properly positioned before tightening.
- Page 21 ASSEMBLY AND INSTALLATION INSTRUCTIONS MUDROOM 25.1 Slide Drawer onto Shelf Slides until slides latch.