Table of Contents
Advertisement
6.14.3.3 Resetting the range
1 Select the item of journey information RANGE.
2 Push both the plus button and the minus
button at the same time for a long time
(> 2.5 s).
RESET is shown on the display screen.
3 If you continue to jiggle the plus and minus
buttons at the same time, the range will be
reset to 0.
6.14.3.4 Changing the tachometer unit
You can change the displayed values from
kilometres to miles.
1 Keep the minus button pressed down.
2 Press the On-Off button (display) briefly (< 1 s).
All values are changed from kilometres to
miles.
6.14.3.5 Displaying versions and type numbers
You can retrieve the sub-system versions and
their type part numbers for maintenance purposes
if the sub-systems provide this type of information
(depends on the sub-system).
The drive system must be switched off.
1 Keep the plus and minus buttons pressed
down at the same time.
2 Press the On-Off button (display) briefly (< 1 s).
The version or type number will be displayed
as moving text.
6.14.3.6 Set display screen brightness
The display must be switched off.
1 Keep the plus and minus buttons pressed
down at the same time.
2 Press the On-Off button (display) briefly (< 1 s).
3 Use the plus button or minus button to adjust
the display screen brightness in such a way
that you can see text and icons sufficiently
clearly.
MY21K01 - 32_1.0_24.09.2020
All manuals and user guides at all-guides.com
6.14.4 Using the USB port
Notice
The USB port is reserved to connect diagnostics
systems. The USB port must be kept completely
closed with the protective cap at all times.
Any moisture penetrating through the USB port
may cause a short circuit in the display.
Regularly check the position of the rubber
cover on the USB port and adjust it as
necessary.
6.14.5 Replacing the battery
When the on-board computer indicates LOW BAT
on the screen, the battery is flat and must be
replaced.
2
Figure 103: Display with attachment screw (1) and battery
compartment cover (2)
1 Remove the display from the handlebars by
unfastening the display attachment screw (1).
2 Use a suitable coin to open the battery
compartment cover (2).
3 Remove the used battery.
4 Insert a new CR 2016 display battery. You can
obtain the batteries recommended by Bosch
from your specialist dealer. Ensure correct
polarity when inserting the display battery.
5 Close the battery compartment again and
fasten the on-board computer to the
handlebars with the attachment screw (1).
Operation
K
K
K
L K
L K
L K
K K
K K K
K
K
K K
K K
K
K
K
A A A L L L K
A L
A L
A L
K
K
K
K K
K
K
K
K
K
L
A L L
A L
A L
A L
A L
A L
A L L
A L
L
L
L L
L
L
L
L
A
A
A
A
A
A
A
A
W A
W W W A
W W A
W A
W A
W A
W A
W A
W A
W A
W A
A
A A
A
A
A
A
W W W W W W A
A
A
A
A
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W W
W
W
W
W
W
W
W W
W
W
W
W
W W
W
W
W W
W
W
W
W
W
W
W
W
W W
W
1
84
Advertisement
Table of Contents
