Reliance electric GV3000 Instruction Manual page 79

Index
A
A-C input
diodes, checking, 9-6 to 9-7
disconnect, installing, 5-2 to 5-4
isolation transformer, 5-1
line branch circuit fuses, 3-7 to 3-8, 5-1 to 5-3
ratings, 2-2
wire sizes, 3-5 to 3-6
wiring, 3-5 to 3-7, 4-1 to 4-8, 5-1 to 5-5
voltage transients, avoiding, 5-1
A-C output
wiring, 3-5 to 3-7, 4-1 to 4-8, 6-1 to 6-2
Air flow, 3-1, 3-4
Alarms, 9-1
Altitude requirements, 3-1
Ambient conditions, 3-1, A-1
Analog output, 2-9
0-10 VDC (J17), 2-9 to 2-11, 2-13, A-2
4-20 mA (J17), 2-9 to 2-11, 2-13, A-2
wiring, 2-14, 7-1, 7-3 to 7-4, 7-8
Analog input speed reference
Input current, wiring, 2-14, 7-1, 7-3 to 7-4, 7-9,
inputvoltage, wiring, 2-14, 7-1, 7-3 to 7-4, 7-9,
0-10 VDC (J4), 2-10 to 2-12, 7-1
4-20 mA (J4), 2-10 to 2-12, 7-1
Area required, 3-2 to 3-4
Audience, intended, 1-2
Block diagram
vector regulation, B-3
volts/hertz regulation, B-2
Board
Bus Clamp, 2-7 to 2-8, 9-11 to 9-12
Capacitor, 2-3 to 2-5, 9-8 to 9-9
Current Feedback, 2-3 to 2-5, 9-8
Gate Driver, 2-5 to 2-8, 9-9 to 9-12
Intelligent Power Module (IPM), 2-7 to 2-8, 9-11
to 9-12
Option, 2-15, 2-16
Power, 2-5, 2-6, 9-9, 9-10
Power Supply, 2-5, 2-6, 9-9, 9-12
Regulator, 2-3 to 2-14, 3-7, 9-8 to 9-10
Thyristor Precharge, 2-8, 9-12
Braking, snubber resistor, 2-9, 2-16, 5-1, A-2
wiring, 2-14, 7-2 to 7-4, 7-14
Bus clamp board, 2-7 to 2-8, 9-11 to 9-12
Cc
Capacitor board, 2-3 to 2-5, 9-8 to 9-9
Capacitors, D-C bus, 9-1 to 9-5
Carrier frequency, 2-9, A-1
CS3000, see Control and Configuration Software
Closed loop, see Vector Regulation
Communication port (J8), 2-10 to 2-11, 2-15, 3-7,
7-1, 7-7
Communication, network, 2-15, 3-7
Componentlocations, 2-3 to 2-8
Conduit size, 4-2 to 4-7
Control and Configuration Software, 1-2, 2-16, 3-7,
7-7
Contacting Reliance, 1-2
Contactors, installing output, 6-1
Contacts
Form A, 2-9, 7-15
Form B, 2-9, 7-15
Control source, 7-1, 7-3 to 7-4, 7-7
PC, 3-7, 7-1, 7-7
wiring, 7-3 to 7-4, 7-7
Control, wiring, 2-13, 7-1 to 7-15
Current Feedback board, 2-3 to 2-5, 9-8
Current transformer, 2-7 to 2-8, 9-11 to 9-12
D
D-C bus
input wiring, 3-5 to 3-6, 4-1 to 4-8, 5-3, 5-5
fuse, 2-7 to 2-8, 9-11 to 9-12
terminals, 9-1 to 9-5
verifying capacitor voltage, 9-1 to 9-5
Digital input wiring, 2-14, 7-2 to 7-4, 7-10 to 7-14
8 (remote/local), 7-2 to 7-4, 7-10
7 (ramp1/ramp2), 7-2 to 7-4, 7-11
6 (forward/reverse), 7-2 to 7-4, 7-12
5 (function loss), 7-2 to 7-4, 7-13
4 (run/jog), 7-2 to 7-4, 7-13
3 (reset), 7-2 to 7-4, 7-14
2 (stop), 7-2 to 7-4, 7-14
(
1 (start), 7-2 to 7-4, 7-14
Digital output wiring, see Status Relays
Dimensions, 3-2 to 3-3
Disconnect, installing A-C input, 5-2 to 5-4
Display, see Keypad/Display
Distribution system capacity, A-C line maximum, 5-1
Drive,
identifying, 2-1
kits, 2-16
Index-1