Built-In Self-Test Codes - Dalsa ML-FM-16K07A Manual

Built-In Self-Test Codes

The Built-In Self-test (BIST) codes are located in the Camera Information pane under Power-on
Status. None of these should occur in a properly functioning camera except OVER_TEMPERATURE.
OVER_TEMPERATURE occurs if the ambient temperature is too high, or if there is insufficient air
circulation or heat sinking.
Bit Name
Number
1 I2C
2 FPGA_NO_INIT
3 FPGA_NO_DONE
4 SENSOR SPI
5 ECHO_BACK
6 FLASH_TIMEOUT
7 FLASH_ERROR
8 NO_FPGA_CODE
9 NO_COMMON_SETTINGS
10 NO_FACTORY_SETTINGS
11 OVER_TEMPERATURE
12 SENSOR PATTERN
13 NO_USER_FPN
14 NO_USER_PRNU
15 CLHS_TXRDY_RETRY
16 (Reserved)
17 NO_USER_SETTINGS
18 NO_ADC_COEFFICIENTS
19 NO_SCRIPT
20 (Reserved)
21 (Reserved)
22 (Reserved)
23 NO_FACT_PRNU
24 NO_FATFS
Status LED
A single red / green LED is located on the back of the camera to indicate status.
LED State
Off
Constant Red
Blinking Red
Blinking Orange
Blinking Green
Constant Green
80 •
Hex Position
0x00000001
0x00000002
0x00000004
0x00000008
0x00000010
0x00000020
0x00000040
0x00000080
0x00000100
0x00000200
0x00000400
0x00000800
0x00001000
0x00002000
0x00004000
0x00008000
0x00010000
0x00020000
0x00040000
0x00080000
0x00100000
0x00200000
0x00400000
0x00800000
Description
Camera not power up or waiting for the software to start
The camera BIST status is not good. See BIST status for diagnosis.
The camera has stopped output and has shut down some components due to an over
temperature condition.
Powering Up. The microprocessor is loading code.
Hardware is good, but the CLHS connection has not been established or has been
broken.
The CLHS Link has been established and data transfer may begin
Binary Translation
0000 0000 0000 0000 0000 0000 0000 0001
0000 0000 0000 0000 0000 0000 0000 0010
0000 0000 0000 0000 0000 0000 0000 0100
0000 0000 0000 0000 0000 0000 0000 1000
0000 0000 0000 0000 0000 0000 0001 0000
0000 0000 0000 0000 0000 0000 0010 0000
0000 0000 0000 0000 0000 0000 0100 0000
0000 0000 0000 0000 0000 0000 1000 0000
0000 0000 0000 0000 0000 0001 0000 0000
0000 0000 0000 0000 0000 0010 0000 0000
0000 0000 0000 0000 0000 0100 0000 0000
0000 0000 0000 0000 0000 1000 0000 0000
0000 0000 0000 0000 0001 0000 0000 0000
0000 0000 0000 0000 0010 0000 0000 0000
0000 0000 0000 0000 0100 0000 0000 0000
0000 0000 0000 0000 1000 0000 0000 0000
0000 0000 0000 0001 0000 0000 0000 0000
0000 0000 0000 0010 0000 0000 0000 0000
0000 0000 0000 0100 0000 0000 0000 0000
0000 0000 0000 1000 0000 0000 0000 0000
0000 0000 0001 0000 0000 0000 0000 0000
0000 0000 0010 0000 0000 0000 0000 0000
0000 0000 0100 0000 0000 0000 0000 0000
0000 0000 1000 0000 0000 0000 0000 0000
Appendix B: Troubleshooting Guide