EWM Tetrix 352 Synergic Operating Instructions Manual page 4

Contents
Notes on using these operating instructions
5.4.3
5.4.4
5.4.5
5.4.6
5.4.7
5.4.8
5.5 Welding programs ................................................................................................................ 55
5.5.1
5.5.2
5.5.3
5.5.4
5.6 Organising welding tasks (Mode "JOB Manager") ............................................................... 57
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
5.7 Interfaces for automation ..................................................................................................... 60
5.7.1
5.7.2
5.7.3
5.7.4
5.8 PC interface ......................................................................................................................... 65
5.8.1
5.9 Access control ...................................................................................................................... 66
5.10 Power-saving mode (Standby) ............................................................................................. 66
5.11 Machine configuration menu ................................................................................................ 67
5.11.1
5.12 Aligning the cable resistance ............................................................................................... 72
6 Maintenance, care and disposal ................................................................................................. 74
6.1 General ................................................................................................................................. 74
6.2 Cleaning ............................................................................................................................... 74
6.2.1
6.3 Maintenance work, intervals................................................................................................. 75
6.3.1
6.3.2
6.3.3
6.4 Disposing of equipment ........................................................................................................ 76
7 Rectifying faults ............................................................................................................................ 77
7.1 Checklist for rectifying faults ................................................................................................ 77
7.2 Warnings .............................................................................................................................. 78
7.3 Error messages .................................................................................................................... 79
7.4 Resetting welding parameters to the factory settings .......................................................... 81
7.5 Software version of the machine control .............................................................................. 81
4
5.4.2.2 Liftarc ..................................................................................................... 40
5.4.2.3 Automatic cut-out .................................................................................. 40
Optimising the ignition characteristics for pure tungsten electrodes .................... 41
5.4.3.1 Tungsten balling function ...................................................................... 41
Operating modes (functional sequences) ............................................................. 42
5.4.4.1 Explanation of symbols ......................................................................... 42
5.4.4.2 Non-latched mode ................................................................................. 43
5.4.4.3 Latched mode ........................................................................................ 44
5.4.4.4 spotArc .................................................................................................. 45
5.4.4.5 spotmatic ............................................................................................... 46
5.4.4.6 Non-latched operation, version C .......................................................... 48
Pulse welding ........................................................................................................ 49
5.4.5.1 Automated pulses .................................................................................. 49
5.4.5.2 Thermal pulsing ..................................................................................... 49
5.4.5.3 Metallurgical pulsing (kHz pulsing) ........................................................ 51
TIG antistick .......................................................................................................... 53
activArc ................................................................................................................. 53
Expert menu (TIG) ................................................................................................ 54
Selection and adjustment ..................................................................................... 55
Example "Program with synergetic setting" .......................................................... 56
Example "Program with conventional setting" ...................................................... 56
Accessories for switching over programs ............................................................. 56
Explanation of symbols ......................................................................................... 57
Creating a new JOB in the memory or copying a JOB ......................................... 58
Loading an existing JOB from the free memory ................................................... 59
Resetting an existing JOB to the factory setting (Reset JOB) .............................. 59
Resetting JOBs 1-128 to the factory setting (Reset All JOBs) ............................. 60
Exit JOB Manager without changes ..................................................................... 60
Connecting the robot interface / industrial bus interface ...................................... 61
5.7.1.1 RINT X12 robot interface....................................................................... 61
5.7.1.2 BUSINT X11 industrial bus interface ..................................................... 62
Automation interface ............................................................................................. 62
Connection socket automation torch .................................................................... 64
Sensor Voltage ..................................................................................................... 65
Connecting the PC 300.net welding parameterisation software ........................... 65
Selecting, changing and saving parameters......................................................... 67
Dirt filter ................................................................................................................. 74
Daily maintenance tasks ....................................................................................... 75
Monthly maintenance tasks .................................................................................. 75
Annual test (inspection and testing during operation) .......................................... 75
099-000141-EW501
22.03.2023