NEC EXP803 Maintenance Manual page 186

Chapter 3 Appendix
Error Message
B006 Expansion ROM not
initialized - PCI
Slot 1D
Expansion ROM not initialized
B007
- PCI
Slot 2D
Expansion ROM not initialized
B008
- PCI
Slot 3D
B01A Expansion ROM not
initialized - PCI
Slot 1A
B022 Serial Port Configuration
Overlapped.
B030 PCI System Error on
Bus/Device/Function
B040 PCI Parity Error on
Bus/Device/Function
B211 PCI Slot 1A - PCIe Link
Failure
B212 PCI Slot 1B - PCIe Link
Failure
B215 PCI Slot 1C - PCIe Link
Failure
B218 PCI Slot 1D - PCIe Link
Failure
B231 PCI Slot 1A - PCIE Link Width
Error
B232 PCI Slot 1B - PCIE Link Width
Error
B235 PCI Slot 1C - PCIE Link Width
Error
B238 PCI Slot 1D - PCIE Link Width
Error
B271 PCI Slot 1A - PCIe Link Speed
Error
B272 PCI Slot 1B - PCIe Link Speed
Error
B275 PCI Slot 1C - PCIe Link Speed
Error
B278 PCI Slot 1D - PCIe Link Speed
Error
DXE_PCI_BUS_OUT_OF_RESOURCES
B800
C000 The error occurred during
fan sensor reading.
C010 The error occurred during
temperature sensor reading
C011 System Temperature out of
the range.
C020 The error occurred during
voltage sensor reading.
C021 System Voltage out of the
range.
C040 SROM data read error
186
Cause
Option ROM expansion in PCI slot
1D failed.
Option ROM expansion in PCI slot
2D failed.
Option ROM expansion in PCI slot
3D failed.
Option ROM expansion in PCI slot
1A failed.
Overlapping serial port
configuration was detected.
PCI SERR was detected.
PCI PERR was detected.
Connection failure of PCIe bus was
detected on PCI slot 1A.
Connection failure of PCIe bus was
detected on PCI slot 1B.
Connection failure of PCIe bus was
detected on PCI slot 1C.
Connection failure of PCIe bus was
detected on PCI slot 1D.
A Link Width error was detected in
PCI Slot 1A.
A Link Width error was detected in
PCI Slot 1B.
A Link Width error was detected in
PCI Slot 1C.
A Link Width error was detected in
PCI Slot 1D.
Link Speed error was detected on
PCI Slot 1A.
Link Speed error was detected on
PCI Slot 1B.
Link Speed error was detected on
PCI Slot 1C.
Link Speed error was detected on
PCI Slot 1D.
Resources to be allocated to PCI
expansion card was insufficient.
An error was detected while
reading fan sensor.
An error was detected while
reading temperature sensor.
A temperature abnormality was
detected.
An error was detected while
reading voltage sensor.
A system voltage abnormality was
detected.
An error was detected while
reading data on SROM.
Express5800/R120f-1E Maintenance Guide
1. POST Error Message
Solution
Disable expansion of option ROM of the
option board that is not used for OS boot.
Run SETUP, and select Advanced → PCI
Configuration → PCI Device Controller and
Option ROM Settings → PCIxx Slot Option
ROM → Disabled. (xx: PCI slot number)
Start SETUP, select Advanced → Serial Port
Configuration, and specify the setting again in
a way that the values of Base I/O or Interrupt in
Serial Port A and Serial Port B will not be the
same.
Contact your sales representative.
The cooling fan has failed or is clogged.
Contact your sales representative.
Contact your sales representative.