Dvcfg (Device Configuration) Menu - Banner Sure Cross Performance DX80 Instruction Manual

®
Sure Cross Performance DX80 Wireless I/O Networks

5.1.5 DVCFG (Device Configuration) Menu

On Gateways, the DVCFG menu allows users to set various device-specific parameters, including the network ID (NID),
slave ID (SLID), baud rate, and parity. In extended address mode, use this menu to also set the maximum number of
radio devices (MAXN) within the network and the extended address binding code (XADR).
Gateway
* DVCFG
Device Config
Single-click
Button 2
Single-click Button 1 to advance through menu
(NID) (SLID)
Network ID Slave ID
Single-click Single-click
Button 2 Button 2
adjust rotary switches adjust rotary switches
to set the network ID to set slave ID, using
button 1 to select the
digits
CUR XX
CUR XX
NEW XX
NEW XX
Single-click Single-click
Button 2 Button 2
SAVES NEW
SAVES NEW
VALUES VALUES
• Baud and Parity. The options for baud rate are: 19200, 38400, or 9600. For parity, select None, Even, or Odd.
• Extended Address (Binding) Code. Binding Nodes to a Gateway ensures the Nodes only exchange data with the
Gateway they are bound to. After a Gateway enters binding mode, the Gateway automatically generates and
transmits a unique extended addressing (XADR), or binding, code to all Nodes within range that are also in binding
mode. The extended addressing (binding) code defines the network, and all radios within a network must use the
same code.
• Max Nodes. Selecting the maximum number of system radio devices (Gateway and all Nodes) changes the timing
for the wireless network. For example, if you are running four Nodes in your wireless network, set the system's
maximum device count to 8. This allows up to 8 radio devices, including the Gateway, in the wireless network and
offers the highest throughput, 62.5 milliseconds, for each Node. The choices are 8, 16, 32, and 48 devices.
• Network ID. The Network ID (NID) is a unique identifier you assign to each wireless network to minimizes the
chances of two collocated networks interfering with each other. Assigning different NIDs to different networks
improves collocation performance in dense installations.
• Slave ID. The slave ID is an identifying number used for devices within a Modbus system. By default, Gateways
are set to Modbus Slave ID 1. When using more than one Modbus slave, assign each slave a unique ID number.
On Nodes, use the DVCFG to set the network ID (NID) and extended address binding code (XADR). The Node address
(NADR), also referred to as a Node ID or device address, is only functional on some models.
34
All manuals and user guides at all-guides.com
(BAUD) (PRTY) (MAXN)
Baud Rate Parity
Single-click Single-click
Button 2 Button 2
9600 None
Even
19200
38400 Odd
Single-click Single-click
Button 2 Button 2
SAVES SAVES
DISPLAYED
DISPLAYED
VALUE VALUE
* Set to 000000 to use the serial number.
www.bannerengineering.com - Tel: 763.544.3164
(XADR)
Extended Addressing
Timing
Single-click Single-click
Button 2 Button 2
Single-click
8 AUTO AUTO
Button 2
16
NETWRK
MANUAL
32
BINDNG
Single-click
Single-click
48
Button 2
Button 1 or 2
Single-click
Button 2
SET
Reboot
XADR
SAVES
DISPLAYED
ADJUST ROTARY
VALUE
SWITCH TO
SET XADR
*
XXXXXX
Single-click
Button 2
CONFRM
XADR
XXXXX
Single-click
Button 2
SAVED