TASKING iSYSTEM Infineon TC377TE User Manual
Emulation adapter
Hide thumbs
Also See for iSYSTEM Infineon TC377TE:
- User manual (20 pages) ,
- Hardware user manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TASKING iSYSTEM Infineon TC377TE
Summary of Contents for TASKING iSYSTEM Infineon TC377TE
- Page 1 Infineon TC377TE Emulation Adapter User Manual V2.8, June 2023 isystem.com/start...
- Page 2 General safety instructions Please read the following safety precautions carefully before putting this device to use to avoid any personal injuries, damage to the instrument, or to the target system. Use this instrument only for its intended purpose as specified by this manual to prevent potential hazards. Use included power cord and power supply The enclosed power supply has been approved for use by iSYSTEM.
-
Page 3: Table Of Contents
Contents Introduction ............................4 Package content ..........................5 Options ..............................6 Target adaptation ........................... 6 Measurement board ..........................9 Operation ............................10 How to connect ............................. 10 Configuration ............................10 Connectors .............................. 13 Standalone operation ........................... 14 Mechanical information ......................16 Emulation Adapter .......................... -
Page 4: Introduction
Introduction Infineon TC377TE Emulation Adapter is based on the 292-pin TC377TE superset device and provides full trace capabilities for the: TC332 TC365 · · TC323, TC333 TC375 · · TC324, TC334 TC327LP, TC337LP, TC367DP, TC377TP (BGA) · · TC364 TC322LP ·... -
Page 5: Package Content
Package content Infineon TC377TE Emulation Adapter is delivered with all the components required for a standalone operation. Target adaptation parts for the Target board adaptation must be ordered separately. Infineon TC377TE Power supply package Emulation Adapter with Infineon microcontroller Power converter Power adapter TC377TE Ordering code:... -
Page 6: Options
Options Target adaptation The Emulation Adapter adaptation to a specific target microcontroller pincount and package is done via a Conversion board and a Solder part. Sometimes also an optional Extender and Socket cover are available. Conversion boards connect between the Emulation Adapter and the matching Solder part, which is being soldered on the embedded target side. - Page 7 Conversion board Solder part QFP Flex Adaptation – Wire adapter As an alternative to the fixed connection, this adaptation provides a flexible connection of the Conversion board to the Solder part via a Connecting part. IANQPACKxxx Solder part Conversion board Connecting part Solder part Socket cover (optional)
- Page 8 QFP Flex Adaptation – Flex PCB adapter This part provides a flexible connection of the Emulation Adapter to the Solder part as an alternative to the fixed connection. Flex PCB adapter Solder part BGA Adaptation Conversion board Extender (optional) Solder part...
-
Page 9: Measurement Board
Measurement board (optional) The Measurement board connects between the Emulation Adapter and the Conversion board. Embedded targets often do not have access to all the MCU pins / connected signals to connect with measurement equipment (oscilloscope, logic analyzer), its use provides easy access to all MCU pins. -
Page 10: Operation
Operation How to connect? How to connect Emulation Adapter (video) - short link: isystem.com/ea-intro · How to connect iSYSTEM Hardware (video) - short link: isystem.com/connect-hardware · Configuration J1: Target reset configuration Jumper J1 connects the Emulation Adapter reset line and the user target board reset line and is populated by default. - Page 11 J4 and J5: GND connection points In case a good ground connection is required, connection points bridge J4 and pin J5 provide easy access to the Emulation Adapter's GND potential. J6 and J7: VFLEX and VAREF VFLEX - If the target’s VFLEX pin isn’t exposed, bridge the jumper J6 to connect VEXT from the target to power VFLEX.
- Page 12 VAREF - If the target’s VAREF2 pin isn’t exposed, bridge the jumper J7 to connect VAREF1 from the target to power VAREF2 Setting the jumper if VAREF2 is present on the device may prevent establishing a debug connection or, in the worst case, can damage the Target board. P2: Power supply configuration Power supply of the Emulation Adapter is configured via the unshrouded 26-pin 2.54 mm header (P2).
-
Page 13: Connectors
Connectors Be aware that debug and trace signals from the Emulation adapter superset device are not connected to the target board. They are exposed only to the connectors on the Emulation adapter. P1: DAP P1 connector exposes DAP debug interface. Signal Signal Description Signal... -
Page 14: Standalone Operation
22-pin AGBT pinout (Revision C1) Signal Direction is described from the BlueBox perspective. Blue color marks the trace signals. Pin 18: TGO (AGBT Trigger out) is connected to the pin TP32.6. Before Revision C1 pin 18 was NC (Not Connected). BlueBox solution supporting AGBT (Aurora GigaBit Trace) interface connects to the P7 connector. - Page 15 Signal Signal P3 connector and J0–J9 jumper correlation table For example, when J2 is in the 3V3 position, it supplies 3.3 V to pin 6 of the P3 connector. When J2 is in the 5V position, it supplies 5 V to pin 6 of the P3 connector pin. Be careful not to supply 5 V to the microcontroller power supply pin, which has declared a maximum voltage 3.3 V! Refer to the microcontroller documentation for detailed information on power supply.
-
Page 16: Mechanical Information
Mechanical information Emulation Adapter Side view of the Emulation adapter complete setup - QFP Fixed Adaptation Top view of the Conversion board Top view of the Emulation Adapter Unit (mm) Ordering code IEA-TC377TE-TOP 32.6 36.4 47.5 IEA-TC377TE- xxxxxx Solder parts Top view of the Solder part Solder part Solder pad view In the case of soldering the Solder part manually, it’s highly recommended to prolong the solder pad... - Page 17 Recommended PCB footprint dimensions: Unit (mm) Ordering code IANQPACK80SE 11.1 11.1 IANQPACK100S 13.1 13.1 IANQPACK144S 17.1 17.1 IA144TQ- 19.5 19.5 0.25 1.625 25.05 25.05 SOLDER IA176TQ- 23.5 23.5 0.25 1.625 29.05 29.05 SOLDER QFP Flex – Wire adapter Unit (mm) Ordering code IEA-TC377TE- TC332W...
-
Page 18: Extenders
Extenders Side view of the Extender Top view of the Extender Unit (mm) Ordering code IA292LFBGA-EXTENDER 3.25 To view Emulation Adapter schematics, visit isystem.com/schematics. -
Page 19: Assembly
Assembly Watch out that the pin 1 position and alignment of all pins. Avoid disassembling and reassembling the hardware setup too frequently. Use the Surface Mount Technology (SMT) to solder the Solder parts to the target instead of the original microcontroller. iSYSTEM provides this soldering service on request. QFP Fixed 1. - Page 20 Slot screw The Slot screw (30mm) is used to fix the Conversion board to the Solder part. The setup becomes mechanically more robust.Screw the Conversion board to the Solder part first, before the Emulation Adapter is attached on top and watch out not to break out the Solder part, e.g., if you accidentally hit the Emulation Adapter from the side.
-
Page 21: Qfp Flex
QFP Flex 1. Solder the Solder part B on the target A. In the case of 0.4 mm pitch variant, assemble the Connecting part C on the Solder part. 2. Assemble in order: Emulation Adapter F, optional Measurement board E, Conversion board D. 3. -
Page 22: Bga
1. Solder the Solder part B on the Target A. 2. (optional, recommended) Connect Extender C to the Solder part B. The Extender protects from damaging the Solder part if the Emulation Adapter setup is frequently assembled and disassembled. Be careful and gentle during this procedure because all parts of the setup are extremely sensitive, and pins can easily bend or even break in the worst-case scenario. -
Page 23: Accessories
Accessories To ease the development process, we recommend using the following iSYSTEM hardware tools: Ordering Code Description IC5700 iC5700 BlueBox On-Chip Analyzer IC5000 iC5000 BlueBox On-Chip Analyzer IC57031 IOM6 Hub (3 x FNet & FBridge) IC57040 IOM6 CAN/LIN IC57041 IOM6 ADIO Debug Adapters and Active Probes Listed Debug Adapters and Active Probes provide tracing functionality for the Infineon TC377TE Emulation Adapter. - Page 24 Visit our website for: Support - isystem.com/support · Tutorials - isystem.com/getting-started · Knowledge Base - kb.isystem.com · www.isystem.com...
Need help?
Do you have a question about the iSYSTEM Infineon TC377TE and is the answer not in the manual?
Questions and answers