TASKING iSystem Infineon TC397XE Hardware User Manual
Emulation adapter
Hide thumbs
Also See for iSystem Infineon TC397XE:
- User manual (12 pages) ,
- Hardware user manual (20 pages)
Related Manuals for TASKING iSystem Infineon TC397XE
Summary of Contents for TASKING iSystem Infineon TC397XE
- Page 1 Infineon TC397XE Emulation Adapter Hardware User Manual V1.8, November 2023 isystem.com/start...
- Page 2 General safety instructions Please read the following safety precautions carefully before putting this device to use to avoid any personal injuries, damage to the instrument, or to the target system. Use this instrument only for its intended purpose as specified by this manual to prevent potential hazards. Use included power cord and power supply The enclosed power supply has been approved for use by iSYSTEM.
-
Page 3: Table Of Contents
Contents Introduction ............................4 Package content ..........................5 Options ..............................6 Target adaptation ........................... 6 Measurement board ..........................7 Operation ............................... 8 How to connect ............................8 Configuration ............................8 Connectors .............................. 10 Standalone operation ........................... 12 Mechanical information ......................14 Emulation Adapter .......................... -
Page 4: Introduction
Introduction Infineon TC397XE Emulation Adapter is based on the 292-pin TC397XE superset device and provides full trace capabilities for the: · TC397Xx · TC387QP · TC3E7Qx devices, where the trace port is not available or lacks the full trace capability. The Emulation Adapter might differ in some peripherals from the target device;... -
Page 5: Package Content
Package content Infineon TC397XE Emulation Adapter is delivered with all the components required for a stan- dalone operation. Target adaptation parts for the Target board adaptation and the Power ad- apter must be ordered separately. Infineon TC397XE Power supply package Emulation Adapter with Infineon Microcontroller Power converter... -
Page 6: Options
Options Target adaptation The Emulation Adapter adaptation to a specific target microcontroller pincount and package is done via a Conversion board and a Solder part. Sometimes also an optional Extender is avail- able. Conversion boards connect between the Emulation Adapter and the matching Solder part, which is being soldered on the embedded target side. -
Page 7: Measurement Board
Measurement board (optional) The Measurement board connects between the Emulation Adapter and the Conversion board. Embedded targets often do not have access to all the MCU pins / connected signals to connect with measurement equipment (oscilloscope, logic analyzer), its use provides easy access to all MCU pins. -
Page 8: Operation
· How to connect Emulation Adapter (video) - short link: isystem.com/ea-intro · How to connect TASKING Hardware (video) - short link: isystem.com/connect-hardware Configuration J1: Target reset configuration Jumper J1 connects the Emulation Adapter reset line and the user target board reset line and is populated by default. - Page 9 Crystal socket Q1 schematics below: J4 and J5: GND connection points In case a good ground connection is required, connection points bridge J4 and pin J5 provide easy access to the Emulation Adapter's GND potential. J6 and J7: VFLEX and VAREF VFLEX - If the target’s VFLEX pin isn’t exposed, bridge the jumper J6 to connect VEXT from the target to power VFLEX.
-
Page 10: Connectors
Setting the jumper if VAREF2 is present on the device may prevent establishing a de- bug connection or, in the worst case, can damage the Target board. P2: Power supply configuration Power supply of the Emulation Adapter is configured via the unshrouded 26-pin 2.54 mm header (P2). - Page 11 Signal Dir- Signal Description Signal Signal Signal Description Signal Dir- ection ection Not Connected DAPEN DAP Enable Ground nRESET Reset 10-pin Infineon DAP pinout Signal Direction is described from the BlueBox perspective. BlueBox supporting Infineon DAP debug and trace interface connects to the P1 connector. P8: DAPE P8 connector exposes DAPE debug interface.
-
Page 12: Standalone Operation
P7: AGBT P7 connector exposes AGBT interface. Signal Dir- Signal Dir- Signal Description Signal Signal Signal Description ection ection AGBT TX0_P TX0_P Vref Reference Voltage AGBT TX0_N TX0_N DAP0 DAP clock Ground DAP1 DAP Data pin Not Connected Not Connected Not Connected DAP2 Optional 2nd Data pin... - Page 13 Signal Signal P3 connector and J0–J9 jumper correlation table For example, when J2 is in the 3V3 position, it supplies 3.3 V to pin 6 of the P3 connector. When J2 is in the 5V position, it supplies 5 V to pin 6 of the P3 connector pin. Be careful not to supply 5 V to the microcontroller power supply pin, which has de- clared a maximum voltage 3.3 V! Refer to the microcontroller documentation for de- tailed information on power supply.
-
Page 14: Mechanical Information
Mechanical information Emulation Adapter Side view of the Emulation Adapter, one Extender and Solder part (each Extender adds approx. 3,25mm) Top view of the Emulation Ad- Top view of the Conversion board apter Unit (mm) Ordering code IEA-TC397XE IEA-TC397XE-TC397 Solder part Top view of the Solder part Unit (mm) Ordering code... -
Page 15: Extender
Extender Side view of the Extender Top view of the Extender Unit (mm) Ordering code IA292LFBGA-EXTENDER 3.25 To view Emulation Adapter schematics, use the short link isystem.com/schematics. -
Page 16: Assembly
Assembly 1. Solder the Solder part B on the Target A. 2. (optional, recommended) Connect Extender C to the Solder part B. The Extender protects from damaging the Solder part if the Emulation Adapter setup is frequently assembled and disassembled. Be careful and gentle during this procedure because all parts of the setup are extremely sensitive, and pins can easily bend or even break in the worst-case scenario. -
Page 17: Accessories
Accessories To ease the development process, we recommend using the following iSYSTEM hardware tools. Ordering Code Description IC5700 iC5700 BlueBox IC5000 iC5000 BlueBox IC57031 IOM6 Hub (3 x FNet & FBridge) IC57040 IOM6 CAN/LIN IC57041 IOM6 ADIO Debug Adapters and Active Probes Listed Debug Adapters and Active Probes provide tracing functionality. -
Page 18: User Notes
User Notes This page is intentionally left blank. - Page 19 This page is intentionally left blank.
- Page 20 Visit our website for: · Support - isystem.com/support · Tutorials - isystem.com/start · Knowledge Base - kb.isystem.com www.isystem.com...
Need help?
Do you have a question about the iSystem Infineon TC397XE and is the answer not in the manual?
Questions and answers