Advertisement
PART LIST
Key No. Qty.
Description
1
4
3/8" x 1 1/4" Screw
2
8
3/8" x 2 1/4" Screw
3
1
Ground Screw
4
4
1/4" x 1" Screw
5
4
1/4" Star Washer
6
12
3/8" Star Washer
7
2
5/16" Star Washer
8
2
5/16" x 3/4" Screw
9
2
3/8" x 1 3/8" Bolt
10
3
1/4" x 2 1/2" Screw
11
2
3/8" x 1 1/8" Screw
12
50
#8 x 3/4" Screw
13
2
1/4" x 1 1/4" Screw
14
8
#8 x 1" Tek Screw
15
12
#8 x 5/8" Screw
16
1
3/8" x 1 3/4" Bolt
17
1
3/8" x 1 1/2" Bolt
18
2
5/16" Motor Screw
19
4
1/4" x 3/4" Screw
20
4
#8 Belt Guide Screw
21
4
5/16" x 1 3/4" Shoulder Bolt
22
1
5/16" x 1 3/4" Bolt
23
1
5/16" x 2 1/4" Bolt
24
7
#8 x 1/2" Screw
25
4
#4 x 1/4" Screw
26
4
#3 x 1/4" Screw
27
2
#8 Star Washer
28
4
5/16" Flat Washer
29
2
3/8" Thrust Washer
30
12
Small Flat Washer
31
5
1/4" Nut
32
5
Hood Clip
33
6
3/8" Nut
34
6
5/16" Nut
35
4
1/4" x 1" Screw
36
30
#8 x 3/4" Truss Head Screw
37
4
Platform Cushion
38
1
Left Frame Cover
39
1
Right Frame Cover
40
1
Warning Decal
41
1
Walking Platform
42
1
Walking Belt
43
2
Belt Guide
44
1
Left Foot Rail
45
1
Right Foot Rail
46
1
Drive Roller/Pulley
47
4
Rubber Cushion
48
2
9/32" Plastic Bushing
49
2
1/2" Pin
50
1
Controller Clamp
Model No. NTL18423-INT.1 R1022A
Key No. Qty.
Description
51
1
Electronics Plate
52
3
Cable Tie
53
1
Latch Crossbar
54
1
Drive Motor
55
1
Motor Belt
56
1
Storage Latch
57
1
Frame
58
2
Rear Foot
59
1
Right Rear End Cap
60
1
Left Rear End Cap
61
1
Idler Roller
62
1
Motor Hood
63
2
Incline Frame Spacer
64
4
3/8" Plastic Bushing
65
2
Frame Spacer
66
1
Incline Frame
67
1
Incline Motor
68
2
Incline Motor Spacer
69
1
Controller
70
1
Power Cord
71
1
Receptacle
72
1
Power Switch
73
1
Belly Pan
74
1
Left Handrail Cover
75
1
Right Handrail Cover
76
1
Left Handrail Outer Cover
77
1
Right Handrail Outer Cover
78
1
Left Inner Handrail Cover
79
1
Right Inner Handrail Cover
80
1
Tray
81
1
Handrail Frame
82
1
Upright Wire
83
1
Handrail Wire
84
1
Left Upright
85
1
Right Upright
86
1
Grommet
87
4
Base Pad Spacer
88
4
Base Pad
89
1
Right Base Cover
90
1
Left Base Cover
91
1
Right Inner Base Cover
92
1
Left Inner Base Cover
93
2
Caution Decal
94
1
Upright Base
95
1
Console
96
1
Console Cover
97
2
Console Bracket
98
2
Console Ground Wire
99
1
Key/Clip
100
1
Left Speaker Cover
34
ASSEMBLY
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you fi nish all assembly steps.
• After shipping, there may be an oily substance
on the exterior of the treadmill. This is normal. If
there is an oily substance on the treadmill, wipe
it off with a soft cloth and a mild, non-abrasive
cleaner.
• Left parts are marked "L" or "Left" and right parts
are marked "R" or "Right."
1. To register your product and activate your
warranty in the UK, go to iFITsupport.eu. If you
do not have internet access, complete the war-
ranty registration card in the warranty booklet
and send it by registered post to the address on
the back cover of the warranty booklet.
To register your product and activate your
warranty in Australia, email or post the
following information to the email address or
postal address on the front cover of this manual.
• your receipt (make sure to keep a copy)
• your name, address, and telephone number
• the model number, serial number, and name
of your product (see the front cover of this
manual)
• To identify small parts, see page 6.
• Assembly requires the following tools:
the included hex keys
one Phillips screwdriver
one adjustable wrench
To avoid damaging parts, do not use power tools.
1
7
Advertisement
