Download Print this page

ICON NordicTrack EXP14i User Manual page 13

Advertisement

SYMPTOM: The walking belt slows when walked on
a. If an extension cord is needed, use only a 3-con-
ductor, 14-gauge (2 mm
2
) cord that is no longer
than 5 ft. (1.5 m).
b. If the walking belt is overtightened, treadmill per-
formance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller screws (C) counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened,
you should be able to lift each edge of the walking
belt 2 to 3 in. (5 to 7 cm) off the walking platform.
Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and
walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
b
5–7 cm
C
c. Your treadmill features a walking belt coated with
high-performance lubricant. IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deterio-
rate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the front cover of this manual.
d. If the walking belt still slows when walked on,
please see the front cover of this manual.
SYMPTOM: The walking belt is off-center
a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller screw clockwise 1/2
of a turn; if the walking belt has shifted to the
right, turn the left idler roller screw counterclock-
wise 1/2 of a turn. Be careful not to overtighten
the walking belt. Then, plug in the power cord,
insert the key, and walk on the treadmill for a few
minutes. Repeat until the walking belt is centered.
a
SYMPTOM: The walking belt slips when walked on
a. First, remove the key and UNPLUG THE POWER
CORD. Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walking
belt is correctly tightened, you should be able to lift
each edge of the walking belt 2 to 3 in. (5 to 7 cm)
off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power
cord, insert the key, and walk on the treadmill for a
few minutes. Repeat until the walking belt is prop-
erly tightened.
a
28
12. Firmly tighten the two 3/8" x 2 1/4" Screws (2)
and the two 3/8" x 1 1/4" Screws (1) in the Right
Upright (85).
Repeat this step on the left side of the
treadmill.
13. Identify the Right Inner Base Cover (91). Slide
the Right Inner Base Cover onto the Upright
Base (94), under the Belly Pan Wire (107), as
shown in the inset drawing. Make sure that the
Belly Pan Wire is in the notch (M) in the Right
Inner Base Cover as shown.
Then, slide the Right Base Cover (89) downward
onto the Right Inner Base Cover (91).
Repeat this step on the left side of the tread-
mill with the Left Inner Base Cover (not
shown) and the Left Base Cover (not shown).
Note: There are no wires on the left side of the
treadmill.
14. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. To
avoid damage to the console, keep the treadmill out of direct sunlight. Keep the included hex keys in a secure
place; one of the hex keys is used to adjust the walking belt (see page 28). Note: Extra hardware may be
included.
12
2
85
1
1
13
89
107
85
M
94
91
M
107
91
13

Advertisement

loading

This manual is also suitable for:

Ntl18423-int.1