Dalsa Falcon 4-CLHS Series User Manual page 38

Line Name
Input 1
Input 2
Output 1
Output 2
Output 3
Output 4
Line Format
Opto-Coupled
Line Mode
Input
Output
Line Status
Low
High
Line Status All
Line Inverter
Off
On
Input Line Detection Level
Threshold for TTL
Input Line Debouncing
Period
Output Line Source
Off
Software Controlled
Pulse On: Start of Frame
Pulse On: Start to Exposure
Pulse On: End of Exposure
Pulse On: Start Of Readout
Pulse On: End Of Readout
Pulse On: Valid Frame
Trigger
Pulse On: Invalid Frame
Trigger
Pulse On: End of Timer1
Pulse On: End of Counter1
Pulse On: Input1
Pulse On: Input2
Pulse On: Link CLHS In
Exposure Active
36  Operational Reference
lineName
Input1
Input2
Output1
Output2
Output3
Output4
LineFormat
OptoCoupled
LineMode
Input
Output
LineStatus
Low
High
LineStatusAll
LineInverter
Off
On
lineDetectionLevel
Threshold_for_TTL
lineDebouncingPeriod
outputLineSource
Off
SoftwareControlled
PulseOnStartofFrame
PulseOnStartofExposure
PulseOnEndofExposure
PulseOnStartOfReadout
PulseOnEndOfReadout
PulseOnValidFrameTrigger
PulseOnInvalidFrameTrigger
PulseOnEndofTimer1
PulseOnEndofCounter1
PulseOnInput1
PulseOnInput2
PulseOnLinkTrigger0
ExposureActive
Description of the physical Pin associated with the
logical line.
Associated with the logical line Input 1
Associated with the logical line Input 2
Associated with the logical line Output 1
Associated with the logical line Output 2
Associated with the logical line Output 3
Associated with the logical line Output 4
Specify the current electrical format of the selected
physical input or output.
The line is opto-coupled.
Reports if the physical Line is an Input or Output
signal.
The line is an input line.
The line is an output line.
Returns the current status of the selected input line.
Line level is low
Line level is high
Returns the current status of all available line signals,
at time of polling, in a single bitfield. The order is
Line1, Line2, Line3, ...
Controls whether to invert the polarity of the selected
input or output line signal.
Leave signal unchanged
Invert line signal
Specifies the voltage threshold required to recognize a
signal transition on an input line.
A signal below 0.8V will be detected as a Logical LOW
and a signal greater than 2.4V will be detected as a
Logical HIGH on the selected input line.
Specifies the minimum delay before an input line
voltage transition is recognized as a signal transition.
Selects which internal signal, event driven pulse or
software control state to output on the selected Line.
LineMode must be Output.
Line output is disabled (Tri-State) or Open with
Optocoupled output.
The OutputLineValue feature changes the state of the
output.
Generate a pulse on the start of the Frame Active
event.
Generate a pulse on the ExposureStart event.
Generate a pulse on the End of Exposure event.
Generate a pulse on the ReadoutStart event.
Generate a pulse on the ReadoutEnd event.
Generate a pulse on the FrameTrigger event.
Generate a pulse on the Invalid Frame(s)Trigger event.
Generate a pulse on the end of timer1.
Generate a pulse on the end of counter1.
Generate a pulse on the Input Signal 1 event.
Generate a pulse on the Input Signal 2 event.
Generate a pulse on LinkTrigger0 signal.
Generate the Exposure Active state on specific output.
1.00
Beginner
DFNC
1.00
Beginner
1.00
Beginner
1.00
Expert
1.01
Expert
1.00
Beginner
1.00
Beginner
DFNC
1.00
Beginner
DFNC
1.00
Beginner
DFNC
Falcon™ 4-CLHS Series