Intelbras IVP 5301 PET PRO User Manual

Passive infrared sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The passive infrared sensor IVP 5301 PET PRO has intelligent detection technology by infrared rays, with an algorithm for analyzing
important parameters such as frequency, amplitude, pulse symmetry through energy calculations, pulse count and pulse coincidence
level. thus, avoiding false shots in dangerous environments. The product also has a shield component, made of ferromagnetic mate-
rial, for greater security in environments with RFI / EMI interference.
The IVP 5301 PET PRO brings the ease of configuration through the DIP Switch of the different types of sensor connections, elim-
inating the connection of resistors in the sensors. We recommend that the sensor configuration be done according to the item 6.
Configuring the IVP 5301 PET PRO Sensor in this manual.

1. Care and safety

» Follow all instructions in the manual for assembling and installing the product.
» This sensor is intended for installation indoors.
» It is important to note that the Pet function is designed for crawling animals, so if the animal is not on the ground, but on top of a bench,
for example, it can be detected thus canceling the Pet , function, as can be seen in the image below:
» Do not touch the surface of the infrared sensor (PIR). If necessary, use a soft cloth moistened with water to clean the product.
» The sensor must be installed where a possible intruder is easily detected, that is, where a person performs movements transverse to the
sensor's detection beams when entering the premises.
Upper view
» Do not install the sensor facing glass doors or windows.
» Do not place objects in front of the sensor. To ensure the detection area, avoid curtains, screens, blinds, or any object that blocks the scan.
» Do not use the sensor in areas with sudden changes in temperature, near air conditioning units, heaters, cooling fans and ovens. Do not
expose the sensor to direct sunlight.
» Make sure that the installation location is stable and that it is not subject to tremors.
» This sensor does not have a Look down or zero zone (see the figure in the item 1.2. Faixa de detecção (vista lateral) ), so make sure that
the installation of the sensor makes it impossible for intruders to enter this area.
» For the use of the articulator, we recommend that the installation be done by a professional installer, as the incorrect use of it may impair
the PET function and the angle of coverage of the sensor.
» For your safety, test the product and systems at least once a week. This is necessary due to changes in environmental conditions, electri-
cal or electronic interruptions and violations. Take all necessary precautions for the safety and protection of your property.
» We recommend that the sensor configuration be done according to the item 6. Configurando o sensor IVP 5301 PET PRO of this manual.
Note: before starting the installation, it is necessary to define the height at which the sensor will be positioned, which can vary from
1.80 to 2.2 m, according to the table in the item 5. Instalação of this manual.

1.1. Scan (upper view)

User Manual
IVP 5301 PET PRO

1.2. Detection range (side view)

1,80 ~2,20 m
zero
zone
1.2

2. Technical specifications

Operating voltage
Operating current
Detection angle
Detection range
Detection method
Sensor
Immunity to animals
Startup time
Installation height
Operating Temperature
Relay output
Sensitivity Jumper
(J.Sens)
LED Jumper
Dimensions (W × H × D)
Metal Shield

3. Product

20
12
11
9
7
10 10
1. Plate fixing screw
3. PIR Sensor
5. Cable routing for installation
7. Sensitivity Jumper
9. Lower front cover Tamper switch
11. Blue LED
13. Undercut for upper cable routing
15. Screw location for installation in the cor-
ner of the wall
17. Top front cover
19. Bottom front cover
Upper view
4 6 8 10 12 m
9-16 Vdc
< 14 mA
90º
12 m
PIR - passive infrared sensor
Low noise PIR
Up to 20 Kg
50 seconds
Check item 5. Installing this guide
-10 ºC ~ +50 ºC
Optional Open / Closed
Controls the sensitivity (through the pulse count) of the PIR
sensor to trigger the alarm
Optional Open / Closed
55 × 140 × 60 mm
Electromagnetic shielding
Cable Cabo
13
13
14
17 14
17
1
8
2 18 18
3
4
15 15
19
19
5
6
16 16 10
10
2. Relay Jumper
4. Connection terminals
6. Screw hole for fixing directly to the wall
8. LEDJumper
10. Screw hole for fixing the lower front
cover
12. Metal Shield
14. Oblong
16. Undercut for lower cable routing
18. Fresnel lens
20. DIP Switch

4. Characteristics

» Micro-controlled sensor;
» Pulse symmetry analysis software;
» Sensitivity adjustment;
» Automatic temperature compensation in real time;
» Immunity to white light up to 20,000 lux;
» High immunity to RFI / EMI;
» Highly effective algorithm against false shots;
» Immunity to pets up to 20 kg;
» Anti-tamper switch for lower front cover (tamper switch);
» Ease of installation with configuration via the DIP Switch;
» Removable connection terminal.

5. Installation

Before starting the installation, it is necessary to define the installation height of the sensor. We recommend that this sensor be
installed according to the table below.
d
h
Distance (d) Pet Installation height (h)
Without the presence of a
Less than or equal pet
1,8 to 2 m
to 4 m With the presence of a
pet
With the presence of a
2,1 to 2,2 m
pet
Greater than 4 m up
to 12 m
Without the presence of a
1,8 to 2.2 m
pet
The IVP 5301 PET PRO sensor does not have an articulator. . So for its installation, follow the procedure below:
Step 1: to remove the lower front cover of the sensor, observe the hole in the cover, as shown in the following figure.
Step 2: if the installation is done directly on the wall, use the oblong located in the upper rear region of the sensor and the hole
indicated for placing the screw just below the connectors.
Orifício do parafuso
Screw hole
If installation is done in the corner of the wall, use the holes indicated on the back cover.
Fixing location of the screws for installation on the
Local de fixação dos parafusos para
wall corner
instalação no canto de parede
Step 3: configure the DIP SWITCH as needed, see item 6. Configurando o IVP 5301 PET PRO .
Step 4: connect the installation cables to the terminals, according to the type of installation, see item 6. Configurando o IVP 5301
PET PRO .
Cable Cabo