Intelbras IVP 1000 Pet SF User Manual
Hide thumbs
Also See for IVP 1000 Pet SF:
- User manual (11 pages) ,
- User manual (14 pages) ,
- User manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intelbras IVP 1000 Pet SF
Summary of Contents for Intelbras IVP 1000 Pet SF
- Page 1 English User manual IVP 1000 Pet SF...
- Page 2 IVP 1000 Pet SF Wireless passive infrared motion sensor Congratulations, you have just purchased a product with Intelbras quality and safety. The IVP 1000 Pet SF motion sensor features passive infrared ray detection technology, with advanced signal analysis technology that prevents accidental triggering.
- Page 3 » Follow all the instructions in the manual for the correct assembly and installation of the product; » LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or process any type of personal data from this product;...
- Page 4 » The Pet function is intended for flat animals weighing up to 20 kg. If the animal is on top of a bench, for example, the Pet function can be canceled. Scan (top view) 90° Detection range (side view) 2 – 2,40 meters zone zero 12 m...
-
Page 5: Table Of Contents
9.1. IVP 1000 Pet SF sensor sensitivity adjustment ....... . . -
Page 6: Technical Specifications
1. Technical specifications Operating voltage 3 Vdc Battery LITHIUM CR123A Operating current 14 mA Consumption at rest 4 uA Detection angle 90° Detection range 12 meters Detection method Immunity to crawling animals Up to 20 kg Ssensitivity adjustment 3 levels (1P-2P-3P) Startup time Up to 60 seconds Operating Temperature... -
Page 7: Product
10. Screw seal 5. LED trigger 4. Sensor opening To access the IVP 1000 Pet SF sensor board for battery change or configuration, squeeze the base latch, located at the bottom. See image below: 5. Sensor stabilization After inserting the battery, the sensor goes into stabilization mode and the red LED flashes for a few seconds. When stabi- lization is complete, the red LED will stop flashing. -
Page 8: Installation
7. Installation After identifying the best installation location, follow the recommendations: » It must be installed at a height of 2.0 m to 2.4 m and positioned so that the intruder makes transverse movements to the sensor’s detection radius. » It is not recommended that the sensor be installed at an angle or using an articulator, as its detection range and Pet function may be impaired in such a way as to cancel the function. -
Page 9: Test
Note: if the control panel used is Intelbras, put it in test mode, this way it will not be necessary to observe the LED, as the control panel will indicate the functioning of the sensor through siren beeps. For more information, consult the central manual on the website: www.intelbras.com.br. -
Page 10: Ivp 1000 Pet Sf Sensor Operation Mode
10. Low battery sensor The IVP 1000 Pet SF sensor controls the battery level and if it is critical it sends the information to the control panel during triggering. In addition, the sensor also signals through the LED, after each activation of the sensor the LED lights up (as usual) and then flashes indicating low battery. -
Page 11: Warranty Term
8. After its useful life, the product must be delivered to an authorized Intelbras service center or directly disposed of in an environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other unused Intelbras brand electronics, can be disposed of at any Green Eletron collection point (waste management facility to which we are associated). - Page 12 Support via e-mail: suporte@intelbras.com.br Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira Rodovia BR 459, km 124, 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000 01.23 CNPJ 82.901.000/0016-03 –...
Need help?
Do you have a question about the IVP 1000 Pet SF and is the answer not in the manual?
Questions and answers