Table of Contents
Advertisement
Attention
f Images may not be projected properly depending on the external device, or the Blu-ray disc or DVD disc, to be played back.
Depending on the selected input, set the [PICTURE] menu → [SYSTEM SELECTOR] and the [DISPLAY OPTION] menu → [SLOT 输入].
f Confirm the aspect ratio of the projection screen and the image, and switch to an optimum aspect ratio from the [POSITION] menu →
[ASPECT].
Note
f When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100C) is connected to the <DIGITAL LINK> terminal, the
input on the DIGITAL LINK output supported device changes each time the <DIGITAL LINK> button is pressed. The input can also be
changed using the RS-232C control command.
For twisted-pair-cable transmitters of other manufacturers, switch the input on the projector to DIGITAL LINK, and then switch the input on
the twisted-pair-cable transmitter.
f <DISPLAYPORT> button and <SLOT 1> button can be used when the optional Interface Board equipped with corresponding input is
installed in the slot.
f When the optional Interface Board for 12G-SDI Optical (Model No.: ET-MDNFB10) is installed in the slot and the SFP module for receiving
or for sending and receiving is not installed in its SFP port, the input will be treated as the status that there is no input signal.
f The operation when the <HDMI> button, <DISPLAYPORT> button, <DVI-D> button, <SDI> button, or <SLOT 1> button is pressed can be
fixed to operation to switch to the specified input using the [SECURITY] menu → [CONTROL DEVICE SETUP].
Switching the input directly with the control panel
The input of the image to project can be switched by directly specifying it with the input selection button on the
control panel.
1)
Press the input selection button (<HDMI>, <DVI-D>, <SDI>, <DIGITAL LINK>, <SLOT>).
<HDMI>
<DVI-D>
<SDI>
<DIGITAL LINK>
<SLOT>
Attention
f Images may not be projected properly depending on the external device, or the Blu-ray disc or DVD disc, to be played back.
Depending on the selected input, set the [PICTURE] menu → [SYSTEM SELECTOR] and the [DISPLAY OPTION] menu → [SLOT 输入].
f Confirm the aspect ratio of the projection screen and the image, and switch to an optimum aspect ratio from the [POSITION] menu →
[ASPECT].
Note
f When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100C) is connected to the <DIGITAL LINK> terminal, the
input on the DIGITAL LINK output supported device changes each time the <DIGITAL LINK> button is pressed. The input can also be
changed using the RS-232C control command.
For twisted-pair-cable transmitters of other manufacturers, switch the input on the projector to DIGITAL LINK, and then switch the input on
the twisted-pair-cable transmitter.
f The <SLOT> button can be used when the optional Interface Board equipped with corresponding input is installed in the slot.
f When the optional Interface Board for 12G-SDI Optical (Model No.: ET-MDNFB10) is installed in the slot and the SFP module for receiving
or for sending and receiving is not installed in its SFP port, the input will be treated as the status that there is no input signal.
f The operation when the <HDMI> button, <DVI-D> button, <SDI> button, or <SLOT> button is pressed can be fixed to operation to switch to
the specified input using the [SECURITY] menu → [CONTROL DEVICE SETUP].
78 - ENGLISH
Chapter 3 Basic Operations — Projecting
Switches the input to HDMI.
The image of the signal input to the <HDMI 输入> terminal is projected. When the optional Interface
Board with the HDMI input is installed in the slot, the input is switched between the <HDMI 输入>
terminal and the input terminal of the Interface Board every time the button is pressed.
Switches the input to DVI-D.
The image of the signal input to the <DVI-D 输入> terminal is projected. When the optional Interface
Board with the DVI-D input is installed in the slot, the input is switched between the <DVI-D 输入>
terminal and the input terminal of the Interface Board every time the button is pressed.
Switches the input to SDI.
The image of the signal input to the <SDI 输入> terminal is projected. When the optional Interface
Board with the SDI input is installed in the slot, the input is switched between the <SDI 输入> terminal
and the input terminal of the Interface Board every time the button is pressed.
Switches the input to DIGITAL LINK.
The image of the signal input to the <DIGITAL LINK> terminal is projected.
Switches the input to the signal of the optional Interface Board installed in <SLOT>.
The input is switched every time the button is pressed when one of the inputs is selected on the
installed optional Interface Board.
Advertisement
Table of Contents
