Table of Contents
Advertisement
[AUTO]
[SINGLE]
[DUAL]
5)
Press the <执行> button.
Note
f The single link is a setting to display one image with one input signal. The dual link is a setting to display one image with two input signals.
f When the [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set as
the combination to use the SDI input, the [SDI LINK] setting cannot be changed.
f When [SDI LINK] is set to [AUTO], use the same format for the signal to be input to the
<SDI 1 输入>/<SDI 2 输入/1 输出>/<SDI 3 输入>/<SDI 4 输入/3 输出> terminals. If different format signal is input to even one terminal,
currently displayed image may not be projected correctly.
f [SDI MAPPING] and [3G-SDI MAPPING] cannot be set when [SDI LINK] is set to [AUTO].
f The content set is displayed in [SDI LINK SETTINGS].
Setting [RESOLUTION] in [SLOT 输入] (SDI input)
1)
Press as to select [SLOT 输入].
2)
Press the <执行> button.
f The [SLOT 输入] screen is displayed.
3)
Press as to select [SINGLE LINK SETTING] or [DUAL LINK SETTING], and press the <执行> button.
f The [SINGLE LINK SETTING] screen or the [DUAL LINK SETTING] screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] is selected.
4)
Press as to select [SDI1], [SDI2], [SDI3], or [SDI4], and press the <执行> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5)
Press as to select [RESOLUTION], and press the <执行> button.
f The [RESOLUTION] screen is displayed.
6)
Press as to select an item, and press the <执行> button.
f Select [AUTO], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], [2048x1080p], [3840x2160p], or
[4096x2160p] when SDI1 input or SDI3 input is selected for [SINGLE LINK SETTING].
f Select [AUTO], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], or [2048x1080p] when SDI2
input or SDI4 input is selected for [SINGLE LINK SETTING].
f Select [AUTO], [1920x1080p], [2048x1080p], [3840x2160p], or [4096x2160p] when [DUAL LINK SETTING]
is selected.
Setting [SDI MAPPING] in [SLOT 输入] (SDI input)
Set the mapping method for the SDI1 input and the SDI3 input.
1)
Press as to select [SLOT 输入].
2)
Press the <执行> button.
f The [SLOT 输入] screen is displayed.
3)
Press as to select [SINGLE LINK SETTING] or [DUAL LINK SETTING], and press the <执行> button.
f The [SINGLE LINK SETTING] screen or the [DUAL LINK SETTING] screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] is selected.
4)
Press as to select [SDI1] or [SDI3], and press the <执行> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5)
Press as to select [SDI MAPPING].
6)
Press qw to switch the item.
f The items will switch each time you press the button.
[AUTO]
152 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
Automatically selects the single link or the dual link.
Sets the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input of the Interface Board to
single link.
(Factory default setting)
Sets the SDI1 input and the SDI3 input of the Interface Board to dual link.
Automatically selects [TYPE1/LEVEL A] or [TYPE2/LEVEL B].
Advertisement
Table of Contents
