Table of Contents
Advertisement
5)
Press as to select a command number, and press the <执行> button.
f You can change the page using qw.
6)
Press asqw to select [TIME], and press the <执行> button.
f The projector is in the adjustment mode (the time is blinking).
7)
Press qw to select "hour" or "minute", and press as or the number (<0> - <9>) buttons to set a
time, and then press the <执行> button.
8)
Press asqw to select [COMMAND].
9)
Press the <执行> button.
f The [COMMAND] detailed screen is displayed.
10) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press qw.
f When [INPUT] is selected, press the <执行> button, and then press asqw to select the input to be set.
[COMMAND]
[POWER ON]
[STANDBY]
[SHUTTER]
[INPUT]
[OPERATING MODE]
*1 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT>.
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100C) is connected to the projector, its input name is
automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*3 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <执行> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <菜单> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <执行> button.
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
—
—
[OPEN]
[CLOSE]
[HDMI]
[DVI-D]
[SDI]
[DIGITAL LINK]
[HDMI1 [SLOT]]
[HDMI2 [SLOT]]
[DVI-D1 [SLOT]]
[DVI-D2 [SLOT]]
[DisplayPort1 [SLOT]]
[DisplayPort2 [SLOT]]
[SDI1 [SLOT]]
*1
[SDI2 [SLOT]]
*1
[SDI3 [SLOT]]
*1
[SDI4 [SLOT]]
*1
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
[INPUT1] - [INPUT10]
[NORMAL]
[ECO]
[QUIET]
*3
[USER1]
[USER2]
[USER3]
Switches on the projector.
Enters standby.
Disables the shutter function (shutter: opened).
Enables the shutter function (shutter: closed).
Switches the input to HDMI.
Switches the input to DVI-D.
Switches the input to SDI.
Switches the input to DIGITAL LINK.
Switches the input to HDMI1 of the Interface Board.
*1
Switches the input to HDMI2 of the Interface Board.
*1
Switches the input to DVI-D1 of the Interface Board.
*1
Switches the input to DVI-D2 of the Interface Board.
*1
Switches the input to DisplayPort1 of the Interface Board.
*1
Switches the input to DisplayPort2 of the Interface Board.
*1
Switches the input to SDI1 of the Interface Board.
Switches the input to SDI2 of the Interface Board.
Switches the input to SDI3 of the Interface Board.
Switches the input to SDI4 of the Interface Board.
Switches the input to SDI OPT1 of the Interface Board.
*1
Switches the input to SDI OPT2 of the Interface Board.
*1
Switches the input to DIGITAL LINK, and switches the input of the
*2
DIGITAL LINK output supported device to the specified input.
Prioritizes brightness.
Prioritizes the life of the light source.
Prioritizes the operation with low noise.
Controls the power with the setting set to [USER1].
Controls the power with the setting set to [USER2].
Controls the power with the setting set to [USER3].
Description
ENGLISH - 191
Advertisement
Table of Contents
