Common Functions; Setting The Display Brightness; Adjusting Speaker Levels; Muting The Av Receiver - Onkyo TX-SR703 Instruction Manual

TX-SR803_En.book Page 58 Friday, August 26, 2005 9:26 AM

Common Functions

This section explains functions that can be used with any
input source.
V1
1
V4 MULTI CH
4
CD
7
PHONO
+ 10
10
- - / - - -
INPUT SELECTOR
MACRO
Press
1
[RECEIVER]
RECEIVER
TAPE/AMP
first
TV
DIMMER
DIMMER
+
CH
DISC
ALBUM
-
PREV
CH
DISPLAY
DISPLAY
REC
LISTENING MODE
STEREO SURR
REPEAT AUDIO
PURE A DIRECT
CH SEL
TEST TONE CH SEL
OPEN/CLOSE VIDEO OFF
STANDBY/ON
STANDBY
ZONE 2
POWER
ON OFF
PURE AUDIO MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3
PHONES
ZONE 2 OFF TONE STEREO DIMMER MEMORY
LISTENING MODE
ZONE 2 LEVEL
PHONES DIMMER

Setting the Display Brightness

You can adjust the brightness of the display.
Press the remote controller's
Remote
controller
[DIMMER] button repeatedly to
DIMMER
select:
• Normal + VOLUME light on.
• Normal + VOLUME light off.
• Dim + VOLUME light off.
AV receiver
• Dimmer + VOLUME light off.
DIMMER
You can also use the AV receiver's
[DIMMER] button (not European mod-
els).
58
V2 V3
+
2 3
DVD T V CH
-
5 6
TAPE TUNER
8 9
T V VOL
0 CLEAR
11 12
2 3 ZONE2
REMOTE MODE
DVD CD HDD
VCR CABLE SAT
CDR MD
SLEEP
SLEEP
ENTER VOL
MUTING
MUTING
PLAYLIST RANDOM
SUBTITLE PLAY MODE
THX ALLST
LEVEL LEVEL
LEVEL – +
L NIGHT Re-EQ
RC-620M
MASTER VOLUME
VIDEO 4 PHONO TAPE TUNER CD DISPLAY
VIDEO 4 INPUT
TUNING
MODE SETUP RETURN ENTER SETUP MIC
CLEAR PRESET PRESET
TUNING DIGITAL S VIDEO VIDEO L AUDIO R
DISPLAY

Adjusting Speaker Levels

You can adjust the volume of each speaker while listen-
ing to an input source. These temporary adjustments are
cancelled when the AV receiver is set to Standby.
1
Use the remote controller's
[CH SEL] button to select each
CH SEL
speaker, and use the [LEVEL–]
and [LEVEL+] buttons to adjust
the volume.
You can adjust the volume of each
LEVEL LEVEL
speaker from –12 dB to +12 dB
(–15 dB to +12 dB for the subwoofer).
Notes:
• You cannot use this function while the AV receiver is
muted.
• Speakers that are set to No or None in the Speaker
Configuration cannot be adjusted.
■ Headphones
While a pair of headphones is connected, you can adjust
the volume of each headphone speaker, from –12 dB to
+12 dB each.
• These settings are stored when the AV receiver is set
to Standby.

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.
Press the remote controller's
[MUTING] button.
The output is muted and the MUTING
MUTING
indicator flashes on the display.
To unmute the AV receiver, press the remote control-
ler's [MUTING] button again, or adjust the volume. The
output is unmuted and the MUTING indicator goes off.
Muting is cancelled when the AV receiver is set to
Standby.
Tip:
You can choose how much the output is muted by using
the Muting Level preference (see page 78).