Advanced Setup; Speaker Setup - Onkyo TX-SR703 Instruction Manual

TX-SR803_En.book Page 70 Friday, August 26, 2005 9:26 AM

Advanced Setup

Speaker Setup

This section explains how to check the speaker settings
and how to set them manually, which is useful if you
change a speaker after performing the automatic speaker
setup.
Some speaker settings are set automatically by the Auto-
matic Speaker Setup function (see page 40).
V4
4
CD
7
PHONO
+ 10
10
- - / - - -
INPUT SELECTOR
1
RECEIVER
RECEIVER
TAPE/AMP
TV
DIMMER
+
ENTER
CH
DISC
ALBUM
-
PREV
CH
DISPLAY
REC
STEREO
REPEAT
PURE A
Speaker Configuration
These settings are set automatically by the Automatic
Speaker Setup function (see page 40).
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
The following crossover frequencies can be specified:
Full Band, 40 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz,
100 Hz, 120 Hz, 150 Hz, 200 Hz.
Specify Full Band for speakers that can output low-fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify
a crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speakers' manuals to determine
the optimum crossover frequencies.
If you're using THX-certified speakers, specify
80 Hz (THX) for all speakers.
1
Press the [RECEIVER] REMOTE
RECEIVER
MODE button, followed by the
[SETUP] button.
The main menu appears onscreen.
70
T V CH
MULTI CH DVD
5 6 -
TAPE TUNER
8 9
T V VOL
0
CLEAR
11 12
MACRO
2 3
ZONE2
REMOTE MODE
DVD CD HDD
VCR CABLE SAT
CDR MD
SLEEP
ENTER VOL
SETUP
MUTING
PLAYLIST RANDOM
LISTENING MODE
SURR
AUDIO SUBTITLE PLAY MODE
DIRECT THX ALLST
2
Use the Up and Down [
buttons to select "3. Speaker
Setup," and then press [ENTER].
ENTER
The Speaker Setup menu appears.
ENTER
3
Use the Up and Down [
buttons to select "Speaker Con-
figuration," and then press
ENTER
[ENTER].
The Speaker Config menu appears.
3-2.Speaker Config
------------------------
a.Subwoofer
ENTER
b.Front
c.Center
d.Surround :80Hz(THX)
e.SurrBack :80Hz(THX)
f.SurrBack Ch
g.LPF of LFE
h.Subwoofer Mode
:-------------
4
Use the Up and Down [
buttons to select "a. Subwoofer,"
and then use the Left and Right
ENTER
[ ]/[ ] buttons to select:
Yes: Select if a subwoofer is con-
nected.
No: Select if no subwoofer is con-
nected.
5
Use the Up and Down [
buttons to select "b. Front," and
then use the Left and Right
ENTER
[ ]/[ ] buttons to select a
crossover frequency.
Note:
• If the Subwoofer setting in step 4 is
set to No, this is fixed at Full Band.
6
Use the Up and Down [
buttons to select "c. Center," and
then use the Left and Right
ENTER
[ ]/[ ] buttons to select a
crossover frequency.
If no center speaker is connected, select
None.
Note:
• If the Front setting in step 5 is set to
anything other than Full Band, Full
Band cannot be selected here.
]/[ ]
]/[ ]
:Yes
:80Hz(THX)
:80Hz(THX)
:2ch
:80Hz(THX)
]/[ ]
]/[ ]
]/[ ]