1. Manuals
  2. Brands
  3. Advantech Manuals
  4. Wireless Access Point
  5. EKI-6333AC-4GP
  6. User manual

Advantech EKI-6333AC-4GP User Manual

Idustrial ieee 802.11 a/b/g/n/ac wi-fi ap with poe
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
EKI-6333AC-4GP
Idustrial IEEE 802.11 a/b/g/n/ac
Wi-Fi AP with PoE

Advertisement

Table of Contents
loading

Related Manuals for Advantech EKI-6333AC-4GP

Summary of Contents for Advantech EKI-6333AC-4GP

  • Page 1 User Manual EKI-6333AC-4GP Idustrial IEEE 802.11 a/b/g/n/ac Wi-Fi AP with PoE...
  • Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
  • Page 3 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.87 inches) between the radiator and your body. EKI-6333AC-4GP User Manual...
  • Page 4 Technical Support and Assistance Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
  • Page 5 The equipment has been exposed to moisture. – The equipment does not work well, or you cannot get it to work according to the user's manual. – The equipment has been dropped and damaged. – The equipment has obvious signs of breakage. EKI-6333AC-4GP User Manual...
  • Page 6 The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Safety Precaution - Static Electricity Static electricity can cause bodily harm or damage electronic devices.

  • Page 7: Table Of Contents

    Bus & Protocol ................81 3.5.2 Data Logging................92 Administration ..................96 3.6.1 Configure & Manage ..............96 3.6.2 System Operation ..............106 3.6.3 FTP ................... 115 3.6.4 Diagnostic ................. 118 Service ....................121 3.7.1 Event Handling................121 EKI-6333AC-4GP User Manual...
  • Page 8 Ethernet Plug & Connector Pin Position..............12 Figure 2.13 Serial Pin Position ....................... 13 Figure 2.14 Example of Connection Diagram................. 13 Figure 2.15 Power Wiring for EKI-6333AC-4GP ................14 Figure 2.16 Grounding Connection ....................16 Figure 2.17 Terminal Receptor: Relay Contact ................16 Figure 2.18 Terminal Receptor: Power Input Contacts ..............
  • Page 9 Object Definition > Scheduling > Configuration > Time Schedule Configuration ..70 Figure 3.84 Object Definition > Scheduling > Configuration > Time Period Definition ....70 Figure 3.85 Object Definition > Grouping > Host Grouping ............71 Figure 3.86 Object Definition > Grouping > Host Grouping ............71 EKI-6333AC-4GP User Manual...
  • Page 10 Field Communication > Bus & Protocol > Modbus............88 Figure 3.127 Field Communication > Bus & Protocol > Modbus............89 Figure 3.128 Field Communication > Bus & Protocol > Modbus > Modbus TCP Slave List .... 91 EKI-6333AC-4GP User Manual...
  • Page 11 Service > Event Handling > Configuration > Digital Input (DI) Profile Configuration ......................122 Figure 3.179 Service > Event Handling > Configuration > Digital Output (DO) Profile List .... 123 Figure 3.180 Service > Event Handling > Configuration >Digital Output (DO) Profile Configuration ......................123 EKI-6333AC-4GP User Manual...
  • Page 12 Service > Event Handling > Notifying Events > Configuration ........128 Figure 3.191 Service > Event Handling > Notifying Events > Notifying Event List ......129 Figure 3.192 Service > Event Handling > Notifying Events > Notifying Event Configuration ..129 EKI-6333AC-4GP User Manual...

  • Page 13: Chapter 1 Introduction

    Chapter Introduction...

  • Page 14: Overview

    Overview The EKI-6333AC-4GP is a feature rich wireless AP with din-rail type design which provides a reliable wireless connectivity for industrial environments. As an 802.11n compliant device, EKI-6333AC-4GP provides 6 times higher data rates than legacy 802.11g devices. With the support of WMM, EKI-6333AC-4GP effectively improves the reliability of wireless connectivity, especially in applications that need high reliability and high throughput data transmission.

  • Page 15: Dimensions

    Management/Notifying Events, Syslog, Email Alart Diagnostic Packet Analyzer, Diagnostic Tools Regulatory CE, FCC Part 15 Subpart B (Class B) Approvals Dimensions 65.84[2.59] 125.08[4.92] R4.50[0.18] 62.38[2.46] 4.50[0.18] R2.25[0.09] 133.32[5.25] 17.22 13.86 [0.68] [0.67] [2.36] [0.67] [0.55] Figure 1.1 Dimensions EKI-6333AC-4GP User Manual...

  • Page 16: Chapter 2 Getting Started

    Chapter Getting Started...

  • Page 17: Hardware

    RJ45 ports x 1 to configure WAN. System LED panel See “LED Indicators” on page 7 for further details. ETH port RJ45 ports x 4. Antenna connector Connector for 2.4G/5G antenna. Antenna connector Connector for 5G antenna. EKI-6333AC-4GP User Manual...

  • Page 18: Rear View

    Figure 2.3 Top View No. Item Description Wall mounting holes Screw holes (x4) used in the installation of a wall mounting plate Ground terminal Screw terminal used to ground chassis Terminal block Connect cabling for power and alarm wiring EKI-6333AC-4GP User Manual...

  • Page 19: Led Indicators

    Not connect to a serial device. Status Solid blue Device is powered on. Device is powered off. 2.4G/5G Solid blue 2.4GHz/5GHz WiFi is enabled. 2.4GHz/5GHz WiFi is disabled. Solid blue 5GHz WiFi is enabled. 5GHz WiFi is disabled. EKI-6333AC-4GP User Manual...

  • Page 20: Connecting Hardware

    DIN rail clip. If seated correctly, the bottom of the DIN rail should be fully inserted in the release tab. DIN rail clip DIN rail DIN rail clip release tab Figure 2.5 Installing the DIN Rail Kit EKI-6333AC-4GP User Manual...

  • Page 21: Figure 2.6 Correctly Installed Din Rail Kit

    Push down on the top of the DIN rail clip release tab with your finger. As the clip releases, lift the bottom of the device, as shown in the following illustration. Figure 2.7 Removing the DIN Rail EKI-6333AC-4GP User Manual...

  • Page 22: Wall Mounting

    Remove the device from the wall and drill holes over each marked location (4) on the wall, keeping in mind that the holes must accommodate wall sinks in addition to the screws. EKI-6333AC-4GP User Manual...

  • Page 23: Wireless Connection

    2.2.3 Wireless Connection Connect the antenna by screwing the antenna connectors in a clockwise direction. W IF I - 6 2 .4 S ig G /5 2 .4 W IF W IF Figure 2.10 Installing the Antenna EKI-6333AC-4GP User Manual...

  • Page 24: Network Connection

    Pin 2 Pin 6 Pin 3 Pin 3 Pin 3 Pin 1 Pin 6 Pin 6 Pin 6 Pin 2 Figure 2.12 Ethernet Plug & Connector Pin Position Maximum cable length: 100 meters (328 ft.) for 10/100BaseT. EKI-6333AC-4GP User Manual...

  • Page 25: Serial Connection

    Figure 2.14 Example of Connection Diagram Mode Specification Digital Input Trigger Voltage (high) Logic level 1: 5V ~ 30V Normal Voltage (low) Logic level 0: 0V ~ 2V Digital Output Voltage (Relay Mode) Depends on external device maximum voltage is Maximum Current EKI-6333AC-4GP User Manual...

  • Page 26: Power Connection

    EKI-6333AC-4GP support 12 to 48 V . Dual power inputs are supported and allow you to connect a backup power source.
  • Page 27 Caution! Do not service equipment or cables during periods of lightning activity. Caution! Do not service any components unless qualified and authorized to do EKI-6333AC-4GP User Manual...

  • Page 28: Figure 2.16 Grounding Connection

    2.2.7.4 Wiring a Relay Contact The following section details the wiring of the relay output. The terminal block on the EKI-6333AC-4GP is wired and then installed onto the terminal receptor located on the EKI-6333AC-4GP. Figure 2.17 Terminal Receptor: Relay Contact The terminal receptor includes a total of six pins: two for PWR1, two for PWR2 and two for a fault circuit.

  • Page 29: Figure 2.18 Terminal Receptor: Power Input Contacts

    Figure 2.19 Removing a Terminal Block Insert a small flat-bladed screwdriver in the V1+/V1- wire-clamp screws, and loosen the screws. Insert the negative/positive DC wires into the V+/V- terminals of PW1. If setting up power redundancy, connect PW2 in the same manner. EKI-6333AC-4GP User Manual...

  • Page 30: Reset Button

    Reset Button Reset configuration to factory default: Press and hold Reset button for 6 seconds. System reboot: Press and hold Reset button for 2 seconds. Note! Do NOT power off the WiFi AP when loading default settings. EKI-6333AC-4GP User Manual...

  • Page 31: Chapter 3 Web Interface

    Chapter Web Interface...

  • Page 32: Log In

    Enter the default user name and password (admin/admin) to log into the management interface. You can change the default password after you have successfully logged in. Click Login to enter the management interface. Figure 3.1 Login Screen Note! Screen may differ depending on Web browsers. EKI-6333AC-4GP User Manual...

  • Page 33: Password

    CPU, Memory, and Connection Sessions. Figure 3.3 Status > Dashboard > System Information The System Information History screen shows the statistic graphs for the CPU and memory. Figure 3.4 Status > Dashboard > System Information History EKI-6333AC-4GP User Manual...

  • Page 34: Basic Network

    ISP. Depending on the model purchased, it can be Static IP, Dynamic IP, PPPoE, PPTP, or L2TP. Network Type It displays the network type for the WAN interface(s). Depending on the model purchased, it can be NAT, Routing, Bridge, or IP Pass-through. EKI-6333AC-4GP User Manual...

  • Page 35: Figure 3.8 Status > Basic Network > Wan & Uplink > Wan Interface Ipv6 Network Status

    The following table describes the items in the previous figure. Item Description It displays corresponding WAN interface WAN IDs. Interface It displays the type of WAN physical interface. Depending on the model purchased, it can be WiFi Module or Ethernet. EKI-6333AC-4GP User Manual...

  • Page 36: Figure 3.9 Status > Basic Network > Wan & Uplink > Lan Interface Network Status

    It displays the type of WAN physical interface. Depending on the model purchased, it can be Ethernet, 3G/4G, etc... Received Packets (Mb) It displays the statistics of downstream packets (Mb). It is reset when the device is rebooted. EKI-6333AC-4GP User Manual...

  • Page 37: Figure 3.11 Status > Basic Network > Lan & Vlan

    It displays whether the VAP wireless signal is enabled or disabled. Op. Mode The WiFi operation mode of VAP. Depends of device model, modes are AP Router, WDS Only and WDS Hybrid, Universal Repeater and Client. SSID It displays the network ID of VAP. EKI-6333AC-4GP User Manual...

  • Page 38: Figure 3.13 Status > Basic Network > Wifi > Wifi Module Ids Status

    Description Op. Band It displays the WiFi operation band (2.4G or 5G) of VAP. It displays the VAP ID. Received Packets It displays the number of received packets. Transmitted Packets It displays the number of transmitted packets. EKI-6333AC-4GP User Manual...

  • Page 39: Administration

    The following table describes the items in the previous figure. Item Description Trap Level It displays the trap level. Time It displays the time stamp of trap event. Trap Event It displays the IP address of the trap sender and event type. EKI-6333AC-4GP User Manual...

  • Page 40: Statistics & Reports

    Export (.xml) Click the Export (.xml) button to export the list to .xml file. Export (.csv) Click the Export (.csv) button to export the list to .csv file. Refresh Click the Refresh button to refresh the list. EKI-6333AC-4GP User Manual...

  • Page 41: Figure 3.20 Status > Statistics & Reports > Network Traffic

    Click Last to see the last page of login statistics. Export (.xml) Click Export (.xml) to export the login statistics to .xml file. Export (.csv) Click Export (.csv) to export the login statistics to .csv file. Refresh Click Refresh to refresh the login statistics. EKI-6333AC-4GP User Manual...

  • Page 42: Basic Network

    Band item will be displayed for radio band selection. Specify the radio band for WiFi uplink connection. If the WiFi module in use is a 2.4G/5GHz selectable module, please select one band for uplink connection. Note: This is only available for 2.4G/5GHz selectable module. EKI-6333AC-4GP User Manual...

  • Page 43: Figure 3.24 Basic Network > Wan & Uplink > Connection Setup

    Figure 3.25 Basic Network > WAN & Uplink > Connection Setup > Internet Connection Configuration The following table describes the items in the previous figure. Item Description WAN Type Click the drop-down menu to select WAN type, options: Static IP, Dynamic IP (Default), PPPoE, PPTP, or L2TP. EKI-6333AC-4GP User Manual...

  • Page 44: Figure 3.26 Basic Network > Wan & Uplink > Connection Setup > Static Ip Wan Type Configuration

    WAN IP Alias is used by the device router and is treated as a second set of WAN IP to provide dual WAN IP address to your LAN network. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 45: Figure 3.27 Basic Network > Wan & Uplink > Connection Setup > Dynamic Ip Wan Type Configuration

    WAN IP Alias is used by the device router and is treated as a second set of WAN IP to provide dual WAN IP address to your LAN network. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 46: Figure 3.28 Basic Network > Wan & Uplink > Connection Setup > Pppoe Wan Type Configuration

    Enable WAN IP Alias then enter the IP address provided by your service provider. WAN IP Alias is used by the device router and is treated as a second set of WAN IP to provide dual WAN IP address to your LAN network. EKI-6333AC-4GP User Manual...

  • Page 47: Figure 3.29 Basic Network > Wan & Uplink > Connection Setup > Pptp Wan Type Configuration

    Check Enable checkbox to enable the MTU (Maximum Transmission Unit) limit, and specify the MTU for the 3G/4G connection. MTU refers to Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. Value Range: 1200 ~ 1500. EKI-6333AC-4GP User Manual...

  • Page 48: Figure 3.30 Basic Network > Wan & Uplink > Connection Setup > L2Tp Wan Type Configuration

    Server IP Address / Enter the L2TP server name or IP Address. Name L2TP Account Enter the L2TP username provided by your service provider. L2TP Password Enter the L2TP connection password provided by your service provider. EKI-6333AC-4GP User Manual...
  • Page 49 WAN IP Alias is used by the device router and is treated as a second set of WAN IP to provide dual WAN IP address to your LAN network. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 50: Figure 3.31 Basic Network > Wan & Uplink > Connection Setup > Network Monitoring Configuration

    DNS2: set the secondary DNS to be the target.  Gateway: set the Current gateway to be the target.  Other Host: enter an IP address to be the target. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 51: Figure 3.32 Basic Network > Wan & Uplink > Load Balance

    Initially, the bandwidth ratio of each WAN is set by default. Value Range: 1 ~ 99. Note: The sum of all weights can’t be greater than 100%. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 52: Figure 3.34 Basic Network > Wan & Uplink > Load Balance

    There are three options can be selected. They are Both, TCP, and UDP. WAN Interface User can select the interface that traffic should go. Note that the WAN interface drop-down menu will only show the available WAN interfaces. EKI-6333AC-4GP User Manual...

  • Page 53: Lan & Vlan

    LAN IP address of this gateway, so there are maximum 253 clients allowed in LAN network. Value Range: 255.0.0.0 (/8) ~ 255.255.255.252 (/30). Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 54: Figure 3.37 Basic Network > Lan & Vlan > Ethernet Lan

    LAN port, and you can do advanced control with its VLAN ID.  Tag-based: Tag-based VLAN allows you to add VLAN ID, and select member and DHCP Server for this VLAN ID. Go to Tag-based VLAN List table. EKI-6333AC-4GP User Manual...

  • Page 55: Figure 3.40 Basic Network > Lan & Vlan > Vlan > Port-Based Vlan List

    Select NAT mode or Bridge mode for the rule. Port Members Select which LAN port(s) and VAP(s) that you want to add to the rule. Note: The available member list can be different for the purchased product. EKI-6333AC-4GP User Manual...
  • Page 56 Secondary WINS The secondary WINS of this DHCP Server. Gateway The Gateway of this DHCP Server. Enable Click Enable checkbox to activate this rule. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 57: Figure 3.42 Basic Network > Lan & Vlan > Vlan > Ip Fixed Mapping Rule List

    Click Enable checkbox to activate this rule. Save Click Save to save the settings. Note! Ensure to always click on Apply button to apply the changes after the web browser refreshed taken you back to the VLAN page. EKI-6333AC-4GP User Manual...

  • Page 58: Figure 3.44 Basic Network > Lan & Vlan > Vlan

    For example, if ID_1 and ID_2 are checked, it means members in VLAN ID_1 can access members of VLAN ID_2, and vice versa. Save Click Save to save the settings. Back Click Back to return the previous screen. EKI-6333AC-4GP User Manual...

  • Page 59: Figure 3.46 Basic Network > Lan & Vlan > Vlan

    PoE cellular gateway properly, as stated in “Connecting Hardware” on page 8. The PSE power sourcing capability is up to 120W. If you intend to connect four 802.3at PD devices to the PoE cellular gateway, you have to make sure your PoE EKI-6333AC-4GP User Manual...

  • Page 60: Figure 3.48 Basic Network > Lan & Vlan > Poe

    Specify the Power Limit for the PoE port. It can be Auto, 802.3af (4W), 802.3af (7W), 802.3af(15.4W), 802.3at(30W), or Manual. If you select Manual, you have to enter the power limit. Value Range: 1 ~ 30 Watts. EKI-6333AC-4GP User Manual...
  • Page 61 PD, otherwise leave it as (0) Always. If the drop-down menu is empty, ensure Time Schedule is preconfigured. Refer to Object Definition > Scheduling > Configuration. Enable Check Enable checkbox to enable the PoE port. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 62: Figure 3.51 Basic Network > Lan & Vlan > Dhcp Server

    The gateway of this DHCP server. Server Click Enable checkbox to activate this DHCP server. Save Click Save to save the settings. Undo Click Undo to cancel the settings. Back Click Back to return the previous screen. EKI-6333AC-4GP User Manual...

  • Page 63: Figure 3.53 Basic Network > Lan & Vlan > Dhcp Server > Mapping Rule List

    The following table describes the items in the previous figure. Item Description Enable Click Enable checkbox to activate the DHCP option function, and the DHCP Server will add the expected options in its sending out DHCPOFFER DHCPACK packages. EKI-6333AC-4GP User Manual...

  • Page 64: Figure 3.57 Basic Network > Lan & Vlan > Dhcp Server > Dhcp Server Option List

    IP Addresses List, separated by “,”: IPv4 format, separated by “,”  Option 144: – Single URL: URL format Enable Click Enable checkbox to activate this setting. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 65: Figure 3.59 Basic Network > Lan & Vlan > Dhcp Server > Dhcp Server Option List

    DHCP requests to the assigned DHCP server via specified WAN interface. DHCP OPTION 82 Check to enable the defined DHCP Option 82 function. Enable Click Enable checkbox to activate this setting. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 66: Wifi

    IEEE 802.11 standard.  2.4G WiFi can select b, g and n only or mixed with each other.  5G WiFi can select a, n and ac only or mixed with each other. EKI-6333AC-4GP User Manual...

  • Page 67: Figure 3.63 Basic Network > Wifi > Wifi Module One/Two > 2.4G Vap List

    Click Add/Edit button to create or edit the settings for a VAP. The VAP Configuration screen appears. Figure 3.64 Basic Network > WiFi > WiFi Module One/Two > VAP Configuration The following table describes the items in the previous figure. Item Description Click the drop-down menu to select a VAP. EKI-6333AC-4GP User Manual...
  • Page 68 It owns the same encryption system as WPA or WPA2. The authentication uses pre-shared key instead of RADIUS server.  When WPA-PSK / WPA2-PSK is selected It owns the same setting as WPA-PSK or WPA2-PSK. The client stations can associate with this device via WPA-PSK or WPA2-PSK. EKI-6333AC-4GP User Manual...

  • Page 69: Figure 3.65 Basic Network > Wifi > Wireless Client List

    Figure 3.65 Basic Network > WiFi > Wireless Client List The following table describes the items in the previous figure. Item Description Module Select Select the WiFi module to check the information of connected clients. For those single WiFi module products, this option is hidden. EKI-6333AC-4GP User Manual...

  • Page 70: Figure 3.66 Basic Network > Wifi > Advanced Configuration

    However, there is some module with selectable band for user to select according to his network environment. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 71: Figure 3.67 Basic Network > Wifi > Advanced Configuration > Advanced Configuration

    The WIDS (Wireless Intrusion Detection System) will analyze all packets and make a statistic table in WiFi status. Go to Status > Basic Network > WiFi for detailed WIDS status. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 72: Figure 3.68 Basic Network > Wifi > Uplink Profile

    To apply the defined uplink profile(s) for the gateway to find a best fit profile for connecting to a certain uplink network, user has to enable the profile auto-connect function (Refer to Basic Network > WiFi > (Module 1/ Module 2) WiFi Configuration. EKI-6333AC-4GP User Manual...

  • Page 73: Figure 3.69 Basic Network > Wifi > Uplink Profile > Profile List

    When Open is selected, the pre-shared WEP key could be set for authentication;  When Shared is selected, the pre-shared WEP key should be set for authentication;  When WPA-PSK or WPA2-PSK is selected, The the TKIP or AES pre-shared key should be set for authentication. EKI-6333AC-4GP User Manual...

  • Page 74: Ipv6

    Select DHCPv6 when your ISP provides you with DHCPv6 services.  Select PPPoEv6 when your ISP provides you with PPPoEv6 account settings.  Select IPv6 when you want to use IPv6 connection. Note: For the products just having 3G/4G WAN interface, only IPv6 is supported. EKI-6333AC-4GP User Manual...

  • Page 75: Figure 3.72 Basic Network > Ipv6 > Configuration > Static Ipv6 Wan Type Configuration

    Primary DNS Enter the WAN primary DNS server. Secondary DNS Enter the WAN secondary DNS server. MLD Snooping Enable/disable the MLD snooping function. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 76: Figure 3.74 Basic Network > Ipv6 > Configuration > Pppoev6 Wan Type Configuration

    Item Description Global Address Enter the LAN IPv6 address for the router. Link-local Address Show the link-local address for LAN interface of router. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 77: Qos

    To utilize your network throughput completely, administrator must define bandwidth control rules carefully to balance the utilization of network bandwidth for all users to access. It is indeed required that an access gateway satisfies the requirements of latency-critical applications, minimum access right guarantee, fair bandwidth usage EKI-6333AC-4GP User Manual...

  • Page 78: Figure 3.77 Basic Network > Qos > Configuration

    Value Range: 1 ~ 6. WAN Interface Select the WAN interface and then the following WAN Interface Resource screen will show the related resources for configuration. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 79: Figure 3.79 Basic Network > Qos > Configuration > Wan Interface Resource

    The following table describes the items in the previous figure. Item Description Interface Specify the WAN interface to apply the QoS rule. Select All WANs or a certain WAN-n to filter the packets entering to or leaving from the interface(s). EKI-6333AC-4GP User Manual...
  • Page 80 Control Function / Set Priority field.  DiffServ Code Points: Select DiffServ Code Points as the resource type for the QoS rule, and you have to select a DSCP marking from the Control Function / DSCP Marking drop-down menu. EKI-6333AC-4GP User Manual...

  • Page 81: Object Definition

    The following table describes the items in the previous figure. Item Description Click Add to configure time schedule rule. Delete Click Delete to delete selected rule(s). Save Click Save to save the settings. Refresh Click Refresh to refresh the time schedule list. EKI-6333AC-4GP User Manual...

  • Page 82: Figure 3.83 Object Definition > Scheduling > Configuration > Time Schedule Configuration

    Week Day Select everyday or one of weekday. Start Time (hh:mm) Start time in selected weekday. End Time (hh:mm) End time in selected weekday. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 83: Grouping

    Type above, and click Join to add. Only one member can be add at a time, so you have to add the members to the group one by one. Member List This field will indicate the hosts (members) contained in the group. EKI-6333AC-4GP User Manual...

  • Page 84: External Server

    Specify the server type of the external server, and enter the required settings for the accessing the server.  Email Server: When Email Server is selected, User Name, and Password are also required. – User Name (String format: any text) – Password (String format: any text) EKI-6333AC-4GP User Manual...

  • Page 85: Certificate

    (http:// en.wikipedia.org/wiki/Public_key_certificate). In a typical public-key infrastructure (PKI) scheme, the signer is a certificate authority (CA), usually a company such as VeriSign which charges customers to issue EKI-6333AC-4GP User Manual...

  • Page 86: Figure 3.89 Object Definition > Certificate > Configuration

     Common Name(CN) is the name of your organization.  Email is the email of your organization. It has to be email address style. Validity Period This field is to specify the validity period of certificate. EKI-6333AC-4GP User Manual...

  • Page 87: Figure 3.91 Object Definition > Certificate > My Certificate > Local Certificate Configuration

    Organization(O) is the name of your organization.  Organization Unit(OU) is the name of your organization unit.  Common Name(CN) is the name of your organization.  Email is the email of your organization. It has to be email address setting only. EKI-6333AC-4GP User Manual...

  • Page 88: Figure 3.93 Object Definition > Certificate > My Certificate > Import

    (Copy and Paste) the PEM encoded certificate string. Apply Click Apply to import the specified certificate file to the gateway. Cancel Click Cancel to discard the import operation and the screen will return to the My Certificates page. EKI-6333AC-4GP User Manual...

  • Page 89: Figure 3.95 Object Definition > Certificate > Trusted Certificate > Trusted Ca Certificate List

    (Copy and Paste) the PEM encoded CA certificate string. Apply Click Apply to import the specified CA certificate to the gateway. Cancel Click Cancel to discard the import operation and the screen will return to the Trusted Certificates page. EKI-6333AC-4GP User Manual...

  • Page 90: Figure 3.98 Object Definition > Certificate > Trusted Certificate > Trusted Client Certificate List

    (Copy and Paste) the PEM encoded certificate string. Apply Click Apply to import the specified certificate to the gateway. Cancel Click Cancel to discard the import operation and the screen will return to the Trusted Certificates page. EKI-6333AC-4GP User Manual...

  • Page 91: Figure 3.101 Object Definition > Certificate > Trusted Certificate > Trusted Client Key List

    (Copy and Paste) the PEM encoded certificate key string. Apply Click Apply to import the specified certificate key to the gateway. Cancel Click Cancel to discard the import operation and the screen will return to the Trusted Certificates page. EKI-6333AC-4GP User Manual...

  • Page 92: Figure 3.104 Object Definition > Certificate > Issued Certificate > Certificate Signing Request (Csr) Import From A File

    The following table describes the items in the previous figure. Item Description Sign When root CA is exist, click Sign sign and issue the imported certificate by root CA. Text filed Enter (copy-paste) the certificate signing request PEM encoded certificate to the gateway. EKI-6333AC-4GP User Manual...

  • Page 93: Field Communication

    Select None / Even / Odd for Parity bit. Action Click Edit to change the operation mode, or modify the parameters mentioned above for the serial interface communication. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 94: Figure 3.108 Field Communication > Bus & Protocol > Virtual Com

    On-Demand is selected in the Connection Control field. Value Range: 0 ~ 3600 seconds. Enable Check Enable checkbox to activate the corresponding serial port in specified operation mode. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 95: Figure 3.110 Field Communication > Bus & Protocol > Virtual Com > Data Packing (For Tcp Client, Tcp Server And Udp Operation Mode)

    Enter the TCP port number. This is the listen port of the remote TCP server. Value Range: 1 ~ 65535. Serial Port Apply the TCP server connection for a selected serial port. Up to 4 TCP servers can be configured at the same time for each serial port. EKI-6333AC-4GP User Manual...

  • Page 96: Figure 3.114 Field Communication > Bus & Protocol > Virtual Com

    On-Demand is selected in the Connection Control field. Value Range: 0 ~ 3600 seconds. Enable Check Enable checkbox to activate the corresponding serial port in specified operation mode. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 97: Figure 3.116 Field Communication > Bus & Protocol > Virtual Com > Trusted Ip Definition (For Tcp Server & Rfc-2217 Operation Mode)

    Figure 3.119 Field Communication > Bus & Protocol > Virtual COM The following table describes the items in the previous figure. Item Description Serial Port It displays the serial port ID of the serial port. The number of serial ports varies from the purchased model. EKI-6333AC-4GP User Manual...

  • Page 98: Figure 3.120 Field Communication > Bus & Protocol > Virtual Com > Legal Host Ip Definition (For Udp Operation Mode)

    Apply the UDP hosts for a selected serial port. Up to 4 UDP servers can be configured at the same time for each serial port. Definition Enable Check Enable checkbox to enable the rule. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 99: Figure 3.122 Field Communication > Bus & Protocol > Virtual Com

    On-Demand is selected in the Connection Control field. Value Range: 0 ~ 3600 seconds. Enable Check Enable checkbox to activate the corresponding serial port in specified operation mode. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 100: Figure 3.124 Field Communication > Bus & Protocol > Virtual Com > Trusted Ip Definition (For Tcp Server & Rfc-2217 Operation Mode)

    Figure 3.126 Field Communication > Bus & Protocol > Modbus The following table describes the items in the previous figure. Item Description Serial Port It displays the name of the serial port used. E.g. SPort-0. The number of serial ports varies from the purchased model. EKI-6333AC-4GP User Manual...

  • Page 101: Figure 3.127 Field Communication > Bus & Protocol > Modbus

    If the slave does not response within the specified time, data would be discarded. This applies to the serially attached Master sent request over to the remote Slave or requests send from the remote Master sent to the serially attached Slave. Value Range: 1 ~ 65535. EKI-6333AC-4GP User Manual...
  • Page 102 Grouping. You may also access to create a group by the Add Rule shortcut button. Setting done through the Add button will also appear in the Host Grouping screen. Then check Enable checkbox to enable this rule. EKI-6333AC-4GP User Manual...

  • Page 103: Figure 3.128 Field Communication > Bus & Protocol > Modbus > Modbus Tcp Slave List

    Description Enter the IP address of the remote Modbus TCP Slave device. Port Enter the TCP port on which the remote Modbus TCP Slave device listens (to the TCP client session request). Value Range: 1 ~ 65535. EKI-6333AC-4GP User Manual...

  • Page 104: Data Logging

    Figure 3.132 Field Communication > Data Logging > Configuration The following table describes the items in the previous figure. Item Description Name Specify a name as the identifier of the Modbus proxy rule. Value Range: 1 ~ 32 characters. EKI-6333AC-4GP User Manual...

  • Page 105: Figure 3.133 Field Communication > Data Logging > Scheme Setup

    Figure 3.134 Field Communication > Data Logging > Scheme Setup > Scheme Configuration The following table describes the items in the previous figure. Item Description Name Specify a name as the identifier of the data logging rule. Value Range: 1 ~ 16 characters. EKI-6333AC-4GP User Manual...
  • Page 106 If any proxy scheme is selected, please create the required Proxy rules in advance, and select from the list. Enable Check Enable checkbox to activate the data logging rule. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 107: Figure 3.135 Field Communication > Data Logging > Log File Management

    Save Click Save to save the settings. Undo Click Undo to cancel the settings. When Download Log button is applied, the web browser will download a file named as ‘log.tar’ to the managing host computer. EKI-6333AC-4GP User Manual...

  • Page 108: Administration

    Figure 3.138 Administration > Configure & Manage > Command Script > Command Script Editor The following table describes the items in the previous figure. Item Description Clean Click Clean to clean text area. (You should click Save to further clean the configuration already saved in the system.) EKI-6333AC-4GP User Manual...
  • Page 109 OPENVPN_LOCAL_CERT A must filled Specify the local certificate for setting OpenVPN client. It will go through Base64 Conversion. OPENVPN_LOCAL_KEY A must filled Specify the local key for the setting OpenVPN client. It will go through Base64 Conversion. EKI-6333AC-4GP User Manual...
  • Page 110 Script file For the configurations that can be configured with standard Linux commands, you can put them in a script file, and apply the script file with STARTUP command. For example, STARTUP=#!/bin/sh STARTUP=echo “startup done” > /tmp/demo EKI-6333AC-4GP User Manual...

  • Page 111: Figure 3.139 Administration > Configure & Manage > Tr-069

    Value Range: 0 ~ 65535. Connection Request You can ask ACS manager provide ACS ConnectionRequest UserName Username and manually set. Connection Request You can ask ACS manager provide ACS ConnectionRequest Password Password and manually set EKI-6333AC-4GP User Manual...

  • Page 112: Figure 3.140 Administration > Configure & Manage > Tr-069 > Stun Settings

    When check the LAN box, it will activate SNMP functions and you can access SNMP from LAN side;  When check the WAN box, it will activate SNMP functions and you can access SNMP from WAN side. EKI-6333AC-4GP User Manual...

  • Page 113: Figure 3.142 Administration > Configure & Manage > Snmp

    Specify this version 1 or version v2c user’s community that will be allowed Read Only (GET and GETNEXT) or Read-Write (GET, GETNEXT and SET) access respectively. The maximum length of the community is 32. Enable Click Enable checkbox to enable this version 1 or version v2c user. EKI-6333AC-4GP User Manual...

  • Page 114: Figure 3.144 Administration > Configure & Manage > Snmp > User Privacy List

    Only (GET and GETNEXT) or Read-Write (GET, GETNEXT and SET) access respectively. OID Filter Prefix The OID Filter Prefix restricts access for this version 3 user to the sub-tree rooted at the given OID. Value Range: 1 ~2080768. EKI-6333AC-4GP User Manual...

  • Page 115: Figure 3.146 Administration > Configure & Manage > Snmp

    Value Range: 1 ~ 32 characters. Password The function is only available when SNMP Version is v3. When your Privacy Mode is authNoPriv or authPriv, you must specify the password for this version 3 trap. Value Range: 8 ~ 64 characters. EKI-6333AC-4GP User Manual...

  • Page 116: Figure 3.148 Administration > Configure & Manage > Snmp > Snmp Mib-2 System

    Click Save to save the settings. Undo Click Undo to cancel the settings. If you use some particular private MIB, you must fill the enterprise name, number and OID. Figure 3.149 Administration > Configure & Manage > SNMP > Options EKI-6333AC-4GP User Manual...

  • Page 117: Figure 3.150 Administration > Configure & Manage > Telnet & Ssh

    LAN or WAN interfaces. You can set which number of service port you want to provide for the corresponding service. Value Range: 1 ~ 65535. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 118: System Operation

    The following table describes the items in the previous figure. Item Description Host Name Enter new host name to replace the current setting. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 119: Figure 3.153 Administration > System Operation > Password & Mmi > Username

    Enter the current password to enable you unlock to change password. New Password Enter new password. New Password Enter new password again to confirm. Confirmation Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 120: Figure 3.156 Administration > System Operation > Password & Mmi > Mmi

    Quick Mode: It takes shorter boot up time, about 90 seconds, without checking the firmware image and create the internal database for User/Group/Captive Portal functions. Note: Use Quick Mode with care, once selected, the User/Group/ Captive Portal function will become non-functional. EKI-6333AC-4GP User Manual...

  • Page 121: Figure 3.157 Administration > System Operation > System Information

    Daylight Saving Time Check Enable checkbox to activate the daylight saving function. When you enabled this function, you have to specify the start date and end date for the daylight saving time duration. EKI-6333AC-4GP User Manual...

  • Page 122: Figure 3.159 Administration > System Operation > System Time

    Check Enable checkbox to activate the NTP service function. When you enabled this function, the gateway can provide NTP server service for its local connected devices. Synchronize Click Active to synchronize the system time with specified time immediately server immediately. EKI-6333AC-4GP User Manual...

  • Page 123: Figure 3.161 Administration > System Operation > System Log

    Email server from Object Definition > External Server > External Server.  E-mail address: Enter the recipient’s Email address. Separate Email addresses with comma ‘,’ or semicolon ‘;’. Enter the Email address in the format of ‘myemail@domain.com’ EKI-6333AC-4GP User Manual...

  • Page 124: Figure 3.162 Administration > System Operation > System Log > Web Log List

    It displays event time stamps. Log column It displays log messages. Previous Click Previous to move to the previous page. Next Click Next to move to the next page. First Click First to jump to the first page. EKI-6333AC-4GP User Manual...

  • Page 125: Figure 3.163 Administration > System Operation > Backup & Restore > Fw Backup & Restore

    The CSS style guide used by the interface can be edited by clicking Edit. The style guide can also be uploaded or downloaded as a CSS file. Note: The file name must be “wmqa01.css”. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 126: Figure 3.164 Administration > System Operation > Backup & Restore > Auto Upgrade

    If the detected firmware or configuration file is newer than the running one, it is downloaded and the router is rebooted automatically. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 127: Ftp

    Specify a port number for FTP connection. The gateway will listen for incoming FTP connections on the specified port. Value Range: 1 ~ 65535. Timeout Specify the maximum timeout interval for the FTP connection. Supported range is 60 to 7200 seconds. EKI-6333AC-4GP User Manual...

  • Page 128: Figure 3.167 Administration > Ftp > Server Configuration > Sftp Server Configuration

    SFTP connection. SFTP Port Specify a port number for SFTP connection. The gateway will listen for incoming SFTP connections on the specified port. Value Range: 1 ~ 65535. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 129: Figure 3.168 Administration > Ftp > User Account

    The embedded FTP server is only for log downloading, so no any write permission is implemented for user file upload to the storage, even Read/Write option is selected. Enable Check Enable checkbox to activate the FTP user account. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 130: Diagnostic

    Select Binary mode or String mode for the serial interface.  VAP: This means the virtual AP. When WiFi and VAP are enabled, it can be selected here. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 131: Figure 3.171 Administration > Diagnostic > Packet Analyzer > Capture Filters

    The packets will be captured when match any port in the rule. Up to 10 ports are supported, but they must be separated with “;”. e.g. 80; 53 Value Range: 1 ~ 65535. EKI-6333AC-4GP User Manual...

  • Page 132: Figure 3.172 Administration > Diagnostic > Diagnostic Tools

    You can specify the MAC address of the computer, in your LAN network, to be remotely turned on by clicking Wake up. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 133: Service

    Email Server Select an Email server profile from external server setting for the email account setting. Email Addresses Specify the destination Email addresses. Enable Click Enable checkbox to activate this account. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 134: Figure 3.177 Service > Event Handling > Configuration > Digital Input (Di) Profile List

    Specify the normal level. It could be Low or High. Signal Active Time Specify the signal active time. Value Range: 1 ~ 10 seconds. Profile Click Enable checkbox to activate this profile setting. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 135: Figure 3.179 Service > Event Handling > Configuration > Digital Output (Do) Profile List

    Value Range: 0 ~ 65535. Duty Cycle Specify the duty cycle for the Digital Output. Value Range: 1 ~100 %. Profile Click Enable checkbox to activate this profile setting. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 136: Figure 3.181 Service > Event Handling > Configuration > Modbus Notifying Events Profile List

    Specify the logic comparator for Notifying Events. It could be ‘>’, ‘<’, ‘=’, ‘>=’, or ‘<=’. Value Specify the value. Value Range: 0 ~ 65535. Enable Click Enable checkbox to activate this profile setting. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 137: Figure 3.183 Service > Event Handling > Configuration > Modbus Managing Events

    Specify the register number of the Modbus device. Value Range: 0 ~ 65535. Value Specify the value. Value Range: 0 ~ 65535. Enable Click Enable checkbox to activate this profile setting. Save Click Save to save the settings. EKI-6333AC-4GP User Manual...

  • Page 138: Configuration

    The following table describes the items in the previous figure. Item Description Managing Events Check Enable checkbox to activate the managing events function. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 139: Figure 3.188 Service > Event Handling > Managing Events > Managing Event List

    (WiFi radio On/Off), the gateway will change the settings as the action for the event.  NAT: Select NAT checkbox and the interested sub-items (Virtual Server Rule On/Off, DMZ On/Off), the gateway will change the settings as the action for the even. EKI-6333AC-4GP User Manual...

  • Page 140: Figure 3.190 Service > Event Handling > Notifying Events > Configuration

    The following table describes the items in the previous figure. Item Description Notifying Events Check Enable checkbox to activate the Notifying Events function. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...

  • Page 141: Figure 3.191 Service > Event Handling > Notifying Events > Notifying Event List

    Once: Event will be executed just once. Interval The function is only available when Trigger Type is Period. Time interval for event execution in period. Value Range: 0 ~ 86400 seconds. Description Enter a brief description for the Notifying Event. EKI-6333AC-4GP User Manual...
  • Page 142 Time Schedule Select a time scheduling rule for the Notifying Event. Notifying Events Click Enable checkbox to activate this Notifying Event setting. Save Click Save to save the settings. Undo Click Undo to cancel the settings. EKI-6333AC-4GP User Manual...
  • Page 143 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2019...

Table of Contents