Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech EKI-6333AC-A Series
Summary of Contents for Advantech EKI-6333AC-A Series
- Page 1 User Manual EKI-6333AC-A Series IEEE 802.11 a/b/g/n/ac WiFi AP...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
- Page 3 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.87 inches) between the radiator and your body. EKI-6333AC-A Series User Manual...
- Page 4 Technical Support and Assistance Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
- Page 5 The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. EKI-6333AC-A Series User Manual...
- Page 6 Always disconnect the power from the device before servicing it. Before plugging a cable into any port, discharge the voltage stored on the cable by touching the electrical contacts to the ground surface. About the Device This device is for indoor use only. EKI-6333AC-A Series User Manual...
-
Page 7: Table Of Contents
3.4.6 Access Control................27 3.4.7 Log....................28 Administration ..................29 3.5.1 Syslog ..................29 3.5.2 NTP / Time.................. 30 3.5.3 HTTP ..................31 3.5.4 Configuration ................32 3.5.5 Firmware Upgrade ..............32 3.5.6 Tools ................... 33 EKI-6333AC-A Series User Manual... - Page 8 Installing the Antenna ....................11 Figure 2.11 Positioning the Antenna....................12 Figure 2.12 Ethernet Plug & Connector Pin Position..............12 Figure 2.13 Power Wiring for EKI-6333AC-A Series ..............13 Figure 2.14 Grounding Connection....................15 Figure 2.15 Terminal Receptor: Relay Contact ................15 Figure 2.16 Terminal Receptor: Power Input Contacts..............
-
Page 9: Introduction
Chapter Introduction... -
Page 10: Overview
Overview The EKI-6333AC-A Series is a feature rich wireless AP with DIN rail type design which provides a reliable wireless connectivity for industrial environments. As an 802.11n compliant device, EKI-6333AC-A Series provides 6 times higher data rates than legacy 802.11g devices. -
Page 11: Dimensions
ARP, ICMP, IPv4, TCP, UDP, DHCP Client, DNS, HTTP, SNTP Regulatory CE, FCC Part 15 Subpart B (Class B) Approvals Dimensions 50.70 [2.00] 15 [0.59] 30 [1.18] 104 [4.09] 6.30 [0.25] 15 [0.59] 95 [3.74] EKI-6333AC WLAN 104 [4.09] Figure 1.1 Dimensions EKI-6333AC-A Series User Manual... -
Page 12: Getting Started
Chapter Getting Started... -
Page 13: Hardware
Description Antenna connector Connector for antenna. System LED panel See “LED Indicators” on page 7 for further details. ETH port RJ45 ports x 1. Reset button Button allows for system soft reset or factory default reset. EKI-6333AC-A Series User Manual... -
Page 14: Rear View
Figure 2.3 Top View No. Item Description Terminal block Connect cabling for power and alarm wiring Ground terminal Screw terminal used to ground chassis Wall mounting holes Screw holes (x4) used in the installation of a wall mounting plate EKI-6333AC-A Series User Manual... -
Page 15: Led Indicators
Designates signal strength Strength WLAN in non-operational state LED Name LED Color Description Ethernet Green on 10Mbps Ethernet connection Green, blinking Ethernet port is transmitting or receiving data Amber 100Mbps Ethernet connection Green 1000Mbps Ethernet connection EKI-6333AC-A Series User Manual... -
Page 16: Connecting Hardware
DIN rail clip. If seated correctly, the bottom of the DIN rail should be fully inserted in the release tab. DIN rail clip DIN rail DIN rail clip release tab Figure 2.5 Installing the DIN Rail Kit EKI-6333AC-A Series User Manual... -
Page 17: Figure 2.6 Correctly Installed Din Rail Kit
Push down on the top of the DIN rail clip release tab with your finger. As the clip releases, lift the bottom of the device, as shown in the following illustration. Figure 2.7 Removing the DIN Rail EKI-6333AC-A Series User Manual... -
Page 18: Wall Mounting
Remove the device from the wall and drill holes over each marked location (4) on the wall, keeping in mind that the holes must accommodate wall sinks in addition to the screws. EKI-6333AC-A Series User Manual... -
Page 19: Wireless Connection
Once the device is installed on the wall, tighten the screws to secure the device. 2.2.3 Wireless Connection Connect the antenna by screwing the antenna connectors in a clockwise direction. 3 A C 6 3 3 E K I- s e t Figure 2.10 Installing the Antenna EKI-6333AC-A Series User Manual... -
Page 20: Network Connection
Pin 2 Pin 6 Pin 3 Pin 3 Pin 3 Pin 1 Pin 6 Pin 6 Pin 6 Pin 2 Figure 2.12 Ethernet Plug & Connector Pin Position Maximum cable length: 100 meters (328 ft.) for 10/100BaseT. EKI-6333AC-A Series User Manual... -
Page 21: Power Connection
EKI-6333AC-A Series support 12 to 48 V . Dual power inputs are supported and allow you to connect a backup power source. - Page 22 Caution! Do not service equipment or cables during periods of lightning activity. Caution! Do not service any components unless qualified and authorized to do EKI-6333AC-A Series User Manual...
-
Page 23: Figure 2.14 Grounding Connection
2.2.5.4 Wiring a Relay Contact The following section details the wiring of the relay output. The terminal block on the EKI-6333AC-A Series is wired and then installed onto the terminal receptor located on the EKI-6333AC-A Series. DC12-48V PWR2... -
Page 24: Figure 2.16 Terminal Receptor: Power Input Contacts
Insert a small flat-bladed screwdriver in the V1+/V1- wire-clamp screws, and loosen the screws. Insert the negative/positive DC wires into the V+/V- terminals of PW1. If setting up power redundancy, connect PW2 in the same manner. EKI-6333AC-A Series User Manual... -
Page 25: Reset Button
Reset Button Reset configuration to factory default: Press and hold Reset button for 5 seconds. System reboot: Press and hold Reset button for 2 seconds. Note! Do NOT power off the WiFi AP when loading default settings. EKI-6333AC-A Series User Manual... -
Page 26: Web Interface
Chapter Web Interface... -
Page 27: Log In
Enter the default user name and password (admin/admin) to log into the management interface. You can change the default password after you have successfully logged in. Click Login to enter the management interface. Figure 3.1 Login Screen Note! Screen may differ depending on Web browers. EKI-6333AC-A Series User Manual... -
Page 28: Password
Enter the username of the profile to change (currently logged in user displays), then enter the new password under the Password field. Re-type the same password in the Confirm Password field. Click Apply to change the current account settings. Figure 3.2 Administration > HTTP EKI-6333AC-A Series User Manual... -
Page 29: Overview
Displays the RAM in kiloBytes (kB) set aside as a temporary holding place for data. Local Network Local IP Address Displays the assigned IP address of the device. Local Netmask Displays the assigned netmask of the device. MAC Address Displays the MAC address of the device. EKI-6333AC-A Series User Manual... -
Page 30: Network Settings
Display the MAC address to which packets are statically forwarded. Apply Click Apply to save the values and update the screen. Note! All new configurations will take effect after rebooting. To reboot the device, click Administration > Tools > Reboot. EKI-6333AC-A Series User Manual... -
Page 31: Wireless Settings
Auto selection allows the device to select a band. The Manual selection provides access to a selection of the option band (2.4G / 5G). The function is only enabled when Operation Mode is set to Client. EKI-6333AC-A Series User Manual... -
Page 32: Advanced
The default is set to 2. Enter a value between 1 and 255. 20/40 Coexistence Select enable to select 20/40 MHz coexistence. Once enabled, the device allows clients operating only on a single channel (20 MHz) to connect to the wireless network (default: disabled). EKI-6333AC-A Series User Manual... -
Page 33: Security
WPA/WPA2-Enterprise. If data encryption is enabled, the key is required and only sharing the same key with other wireless devices can the communication be established. Apply Click Apply to save the values and update the screen. EKI-6333AC-A Series User Manual... -
Page 34: Statistics
Display the current Tx packets. TX bytes Display the current Tx bytes. RX packets Display the current Rx packets. RX bytes Display the current Rx bytes. Apply Click Apply to save the values and update the screen. EKI-6333AC-A Series User Manual... -
Page 35: Site Survey
Disable, Deny or Allow. In the Deny or Allow menu, enter the MAC address of the target device - support for up to 32 target devices. Apply Click Apply to save the values and update the screen. EKI-6333AC-A Series User Manual... -
Page 36: Log
3.4.7 To access this page, click Wireless Settings > Log. Figure 3.11 Wireless Settings > Log The following table describes the items in the previous figure. Item Description Download Click Download to download the log file. EKI-6333AC-A Series User Manual... -
Page 37: Administration
To access this page, click Administration > Syslogd. Figure 3.12 Administration > Syslogd The following table describes the items in the previous figure. Item Description Download Click Download to download the log file. EKI-6333AC-A Series User Manual... -
Page 38: Ntp / Time
Click the drop-down menu to enable the NTP server. Time Zone Click the drop-down menu to select a system time zone. NTP Server Enter the address of the SNTP server. Apply Click Apply to save the values and update the screen. EKI-6333AC-A Series User Manual... -
Page 39: Http
Enter the name of the user entry. Password Enter the character set for the define password type. Confirm Password Retype the password entry to confirm the profile password. Apply Click Apply to save the values and update the screen. EKI-6333AC-A Series User Manual... -
Page 40: Configuration
To access this page, click Administration > Firmware Upgrade. Figure 3.16 Administration > Firmware Upgrade The following table describes the items in the previous figure. Item Description Browse Click Browse to select the configuration file. Upload Click Upload to upload to the current version. EKI-6333AC-A Series User Manual... -
Page 41: Tools
Host names are composed of series of labels concatenated with periods. Each label must be between 1 and 63 characters long, maximum of 64 characters. Ping Click Ping to display ping result for the IP address. EKI-6333AC-A Series User Manual... - Page 42 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2018...