Table of Contents
Advertisement
Quick Links
TLP Pro 320C • Setup Guide
Overview
The Extron TLP Pro 320C is a 3.5 inch Cable Cubby
depth. It is ideal for any AV application requiring a compact, Cable Cubby touchpanel with a customizable interface. This guide
provides instructions for experienced installers to mount and install a TLP Pro 320C touchpanel. For more complete instructions,
see the TLP Pro 320C User Guide, at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software (available from www.extron.com):
Global Configurator Plus and Professional — for setting up and configuring the control processor and touchpanel.
GUI Designer — for designing layouts for Extron TouchLink
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you will also require the following:
IP address
User name — by default these are either admin or user.
Passwords — by default these are either extron (for admin) or the field is left blank (for user).
Make a note of the touchpanel MAC address.
Make sure you are familiar with all the included parts and have all the necessary tools (see
on page 2) for installing the Cable Cubby.
Included Parts
AC Power Module
1
2,3
Pass-through AAPs
Blank AAPs
4
1-position bracket kit
2-position bracket kit
3-position bracket kit
NOTES:
1
Inside the US, the TLP Pro 320C can be purchased with or without an AC power module. Outside the US, see
www.extron.com
2
Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than the front bracket and has two holes for
screws.
Active or Passive AAPs are not provided. Purchase them separately (see www.extron.com).
3
4
Single-space brackets can only be installed in one location (see the
touchpanel with a flip-up, 320x240 LCD touchscreen with 18-bit color
®
Subnet mask
1
1
0
4
3
4
3
3
5
0
1
0
2
1
3
1
1
1
TLP Pro 320C
to find a power module that is suitable for your location.
Pro touchpanels and third party touch interfaces.
®
Gateway
Table Clamps
AC Power Module*
Zip Ties
note and figure
Product Category
Tools Required for Installation
Pass-thru AAPs
Blank AAPs
1 Pos
2 Pos
3 Pos
AAP Shelf Bracket Kits
(2 brackets/kit)
Extron
#4−40 Screws
Removal Tool
and Nuts
on page 4).
1
Advertisement
Table of Contents
Related Manuals for Extron electronics TLP Pro 320C
Summary of Contents for Extron electronics TLP Pro 320C
- Page 1 Removal Tool and Nuts NOTES: Inside the US, the TLP Pro 320C can be purchased with or without an AC power module. Outside the US, see www.extron.com to find a power module that is suitable for your location. Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than the front bracket and has two holes for screws.
- Page 2 Ensure there is enough space for all the system cables and components, including cable retractors, if they are required. The space requirements for retractors are shown in the TLP Pro 320C User Guide, which is available at www.extron.com. Decide on the method for cutting a hole in the table:...
- Page 3 (see “Preparing the Table” in the TLP Pro 320C User Guide). There are three methods for cutting the hole in the table: Using a hand router Recommended method —...
- Page 4 If required, Extron cable retractors should be installed in the enclosure at this stage. For complete information about retractors and how to install them, see the TLP Pro 320C User Guide and Retractors User Guide at www.extron.com. Step 5 — Install Power Module (Optional) ATTENTION: •...
- Page 5 Product Category Step 7 — Install the AAP Assembly From under the table, push the first AAP assembly through the bottom of the enclosure. The holes in the rear bracket must align with the bottom row of holes on the rear face of the enclosure.
- Page 6 « Power Supply » du TLP Pro 320C User Guide. NOTE: The TLP Pro 320C ships without a power supply. Either the 12 VDC power supply or the power injector must be purchased separately. Network and Power over Ethernet (PoE) Connector — Connect the touchpanel to the LAN using a twisted pair cable, terminated with an RJ-45 connector.
- Page 7 Reset LED— This LED indicates power status and reset status of the device. Reset button — This button allows the unit to be reset. The TLP Pro 320C has three reset modes that are initiated by Reset Modes: a Brief Summary pressing the reset button (see on page 8).
- Page 8 TLP Pro 320C • Setup Guide (Continued) Reset Modes: a Brief Summary The TLP Pro 320C offers the following reset modes (see the TLP Pro 320C User Guide for complete information): Use factory firmware: • Press and hold the button (see...
Need help?
Do you have a question about the TLP Pro 320C and is the answer not in the manual?
Questions and answers