Configure A Tracer Bas Controller With A New Ip Address - Digi WR21 Installation, Operation And Maintenance Manual

C C o o n n f f i i g g u u r r a a t t i i o o n n R R e e q q u u i i r r e e m m e e n n t t s s
Table 1. Subnet Mask to Prefix Length
Subnet Mask
255.255.240.0
255.255.248.0
255.255.252.0
255.255.254.0
255.255.255.0
255.255.255.128
255.255.255.192
255.255.255.224
255.255.255.240
3. Click the O O k k button to the right of line 10 to complete the edit, then the S S a a v v e e button to save
4. After all changes have been made, save the configuration by clicking on S S a a v v e e c c o o n n f f i i g g u u r r a a t t i i o o n n
E E x x a a m m p p l l e e : : if the subnet mask used was 255.255.255.128, then 192.168.2.0/25 should be used in
the firewall rule. Replace 192.168.209.10 with the new IP address of the Tracer BAS controller. If
the Tracer BAS controller was configured to O O b b t t a a i i n n I I P P A A d d d d r r e e s s s s A A u u t t o o m m a a t t i i c c a a l l l l y y u u s s i i n n g g D D H H C C P P ,
choose a static IP address to use instead. This address can be any address that is on the same
subnet as the IP address used for E E T T H H 1 1 – – I I n n t t e e r r n n a a l l N N e e t t w w o o r r k k , excluding x.x.x.0, x.x.x.1, or x.x.
x.255 (when using a mask of 255.255.255.0). If your subnet mask is different, consult
subnet-calculator.com

Configure a Tracer BAS Controller with a New IP Address

Because the original IP addresses from the Tracer BAS controller were removed and placed them
on the WAN port of the Digi device, It is necessary to change the IP addresses in the Tracer BAS
controller.
1. Log in to Tracer BAS controller and then navigate to the IP Configuration page
2. Enter the new IP address, Subnet Mask and Default Gateway of the Tracer BAS controller.
N N o o t t e e : : For the IP address, choose an IP not already in use on the LAN side of the WR21 (E E T T H H 1 1 ) ) .
3. After you have entered the information above, click S S a a v v e e .
16
prefix Length
/20
/21
/22
/23
/24
/25
/26
/27
/28
the changes. Finally, scroll down and click A A p p p p l l y y to apply changes.
in the left hand menu, then S S a a v v e e a a l l l l in the right window.
for a list of valid IP addresses in a given subnet.
(I I n n s s t t a a l l l l a a t t i i o o n n > > I I d d e e n n t t i i f f i i c c a a t t i i o o n n a a n n d d C C o o m m m m u u n n i i c c a a t t i i o o n n > > I I P P C C o o n n f f i i g g u u r r a a t t i i o o n n ) )
This should match the IP address used to configure the firewall rules in the previous steps
(the example address used was 192.168.209.10). For the Gateway, enter the same IP
address you entered on the E E T T H H 1 1 configuration of the WR21 in the prior steps in this
document (In this example 192.168.209.1 was used).
www.
BAS-SVX069F-EN