Digi TransPort WR21 Installation Manual
Hide thumbs
Also See for TransPort WR21:
- Installation, operation and maintenance manual (48 pages) ,
- Handbook (26 pages) ,
- Installation manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Digi TransPort WR21
Summary of Contents for Digi TransPort WR21
-
Page 1: Installation Guide
T r a n s P o r t W R 2 1 ® Wireless Routers Installation Guide January 30, 2012... - Page 2 Digi International reserves the right to modify or revise all or part of this document, its contents, and any products described herein at any time without prior notification and shall not be responsible for any loss, cost or damage, including consequential damage, caused by reliance on these materials.
- Page 3 However, cellular-based products contain radio devices which require specific consideration. Please take the time to read and understand the following guidance. Digi International assumes no liability for an end user’s failure to comply with these precautions.
-
Page 4: Table Of Contents
Digi TransPort ® WR21 Installation Guide Table of Contents 1 Package Contents ..................5 2 Introduction ....................6 2.1 Front Panel Features ..................7 2.2 Rear Panel Features ..................8 3 Installation ....................9 4 Configuration ..................... 11 4.1 Network Settings ....................11 4.2 Web Interface ....................11... -
Page 5: Package Contents
Digi TransPort ® WR21 Installation Guide 1 Package Contents TransPort WR21 Cellular Antenna(s) Ethernet Cable Installation Guide Power Supply Adapters [Non-US models only] Power Supply (some models may include a DC Power Cord or have no Power Supply) If any item is missing or damaged, please contact your supplier. Also, make a record of any damage that may have occurred during shipping and report it to the carrier. -
Page 6: Introduction
Digi TransPort ® WR21 Installation Guide Preface This guide describes the installation procedure for the Digi TransPort WR family of routers. It is intended to provide sufficient information to be able to connect the unit to terminal equipment and power-on the unit. A complete reference guide to the software features that are available on the product is available separately in PDF format and can be downloaded from the Digi International web site (www.digi.com). -
Page 7: Front Panel Features
Digi TransPort ® WR21 Installation Guide 2.1 Front Panel Features 1. SIM/R-UIM Sockets (SIM card models only) - SIM 1 and SIM 2 are for use with the Subscriber Identification Module(s) (SIMs) or Removable User Identification Module(s) (R-UIMs). 2. LED Status Indicator - POWER - Illuminates steady when power is connected. -
Page 8: Rear Panel Features
Digi TransPort ® WR21 Installation Guide 2.2 Rear Panel Features WWAN WWAN SECONDARY PRIMARY SERIAL 0 9-30VDC LAN 0 LAN 1 2A MAX 1. Secondary Cellular (WWAN) Antenna Connector - This SMA female connector is used to connect the unit’s secondary cellular antenna. It is highly recommended to use the secondary antenna for diversity. In most circumstances, dual antennas will provide improved signal strength thus better performance. -
Page 9: Installation
Mounting Tips The Digi TransPort WR21 should be positioned on a flat, level surface or via a wall-mount, rackmount, or DIN rail mounting brackets (see the Accessories section on page 18 for all options). The unit is designed for indoor use and should be mounted in a location with adequate ventilation. - Page 10 If this is the case, Digi has many antenna options to chose from -- please contact us or visit www.digi.com. If antennas other than the supplied antenna(s) are used, the separation between the two should be no less than five inches (5”).
-
Page 11: Configuration
Digi TransPort ® WR21 Installation Guide 4 Configuration Once the unit has been installed and powered up, it needs to be configured to communicate with the LAN and WAN. Configuration is performed either using the Command Line Interface (CLI) or the Web Interface. - Page 12 Digi TransPort ® WR21 Installation Guide The Quick Start Wizard is located in the Getting Started section on the Home menu. 4.2.1 Cellular: CDMA If your unit is to be used on a CDMA network, the embedded module must be provisioned on the network before it can make a connection.
- Page 13 Digi’s configuration file. As the mobile account information is stored on the CDMA module, performing a factory reset on the unit will not remove provisioning information from the CDMA module.
-
Page 14: Command Line Interface (Cli)
Digi TransPort ® WR21 Installation Guide 4.3 Command Line Interface (CLI) In order to configure the unit serially, ensure that the unit is connected to a PC (as outlined in Step 4 page 10 of the Installation section). Also, terminal emulation software (such as HyperTerminal) will be required. - Page 15 (normally this router’s LAN IP address) DHCP 0 MASK x.x.x.x The subnet mask DHCP clients should use DHCP 0 DNS The DNS server DHCP clients should use For more information on CLI commands, visit http://www.digi.com/support/ and view the various reference manuals available. Page 15...
-
Page 16: Troubleshooting
“straight through” RS232 serial cable. This will allow you to change the configuration via the Command Line Interface (CLI). Please refer to the Digi TransPort User Guide for information on how to use the CLI. The User Guide can be downloaded from the Digi Support site. If you have further questions about your product please contact Digi Technical Support (see page 2 for contact information). -
Page 17: Specifications
Mobile Certifications - CDMA/ CDG TIA/EIA-690, CDG TIA/EIA-98-E EV-DO Wireless Carrier Certifications Certified by most major carriers. See www.digi.com for current listing. Safety UL 60950, CSA 22.2 No. 60950, EN60950 Emissions / Immunity CE, FCC Part 15 Class B, AS/NZS CISPR 22, EN55022 Class A... -
Page 18: Accessories
Digi TransPort ® WR21 Installation Guide 7 Accessories AC Power Supplies North America (NA) 76000823 International (Intl.) 76000823 NA - Extended Temp. 76000752 Intl. - Extended Temp. 76000788 DC Power Cords Barrel Plug to Bare Wire 76000821 Barrel Plug to 12V Auto Power Outlet... -
Page 19: Appendix A: Serial 0 Port Pin-Out Diagram
Digi TransPort ® WR21 Installation Guide Appendix A: SERIAL 0 Port Pin-out Diagram WWAN WWAN SECONDARY PRIMARY SERIAL 0 9-30VDC LAN 0 LAN 1 2A MAX Pin 1 Pin 9 SERIAL 0 RS232 Pin # Direction RS232 DCE Description Data Carrier Detect... -
Page 20: Appendix B: Software Options
Digi TransPort ® WR21 Installation Guide Appendix B: Software Options Features Standard Enterprise (includes Standard feature set) Local Python Programming Protocols HTTP, HTTPS, FTP, Same as Standard plus iDigi; Dynamic DNS SFTP, SSL, SMTP, client compatible with BIND9/No-IP/DynDNS iDigi SNMP, SNMP... - Page 21 Digi TransPort ® WR21 Installation Guide Standard Version Firewall Advanced Version Firewall Actions: Actions: • block • block • pass • pass • pass-ifup • pass-ifupnr • debug • touser • dscp • vdscp Options: Options: • routeto • onvlan •...
- Page 22 Digi TransPort ® WR21 Installation Guide Declaration of Conformity EC Declaration Of Conformity Digi International Manufacturer's Name: 11001 Bren Road East Manufacturer's Address: Minnetonka, MN 55343 declare under our sole responsibility that the product: Transport WR21 Product Name: Model Numbers:...
-
Page 23: Product Disposal Instructions
This product contains high quality materials and components which can be recycled. At the end of its life this product MUST NOT be mixed with other commercial waste for disposal. Check with the terms and conditions of your supplier for disposal information. Digi International Ltd WEEE Registration number: WEE/HF1515VU Page 23... - Page 24 © 2011 Digi International Inc. All rights reserved. Digi, Digi International, the Digi logo, a Digi International Company, the Digi web site, Digi Remote Manager, Digi TransPort, Digi TransPort WR, and Digi TransPort WR21 are trademarks or registered trademarks of Digi International, Inc.