Digi TransPort WR41 Installation Manual
Hide thumbs
Also See for TransPort WR41:
- Installation manual (21 pages) ,
- Quick start manual (2 pages) ,
- User manual (948 pages)
Related Manuals for Digi TransPort WR41
Summary of Contents for Digi TransPort WR41
-
Page 1: Installation Guide
T r a n s P o r t W R 4 1 U t i l i t y ® Installation Guide 90001276_B July 22, 2013... - Page 2 Digi International reserves the right to modify or revise all or part of this document, its contents, and any products described herein at any time without prior notification and shall not be responsible for any loss, cost or damage, including consequential damage, caused by reliance on these materials.
-
Page 3: Product Disposal Instructions
However, cellular-based products contain radio devices which require specific consideration. Please take the time to read and understand the following guidance. Digi International assumes no liability for an end user’s failure to comply with these precautions. -
Page 4: Table Of Contents
TransPort ® WR41 Utility Installation Guide Table of Contents 1 Package Contents ..................5 2 Introduction ....................6 3 Product Features ..................7 3.1 Exterior Features ....................7 3.2 Interior Features ....................9 4 Mounting ..................... 10 4.1 Cable Installation ....................10 5 Installation ....................11 5.1 Install SIM Card(s) ....................11 5.2 Connect Antenna(s) ..................12 5.3 Connect Power ....................13... -
Page 5: Package Contents
TransPort ® WR41 Utility Installation Guide 1 Package Contents TransPort WR41 Utility Installation Guide Mounting Kit Installation Guide Cellular Digi is Going Green! Antenna (x2) To reduce paper and provide you with the latest product information, the user’s guide for this product is available online at: www.digi.com/wr41... -
Page 6: Introduction
TransPort ® WR41 Utility Installation Guide Preface This guide describes the installation procedure for the TransPort WR41 Utility. It is intended to provide sufficient information to be able to connect the unit to terminal equipment and power-on the unit. A complete reference guide to the software features that are available on the product is available separately in PDF format and can be downloaded from the Digi International web site (www.digi.com). -
Page 7: Product Features
TransPort ® WR41 Utility Installation Guide 3 Product Features 3.1 Exterior Features 3.1.1 Front View 1. Cellular Antenna TNC Connector 2. Vent Plug 3. Locking Hasp Page 7... -
Page 8: Back View
TransPort ® WR41 Utility Installation Guide 3.1.2 Back View 1. Cellular Antenna TNC Connector 2. Mounting Bracket 3. 1” Conduit Hole 4. 1/2” Conduit Hole Note: Some of the conduit holes shown below may not be accessible. Page 8... -
Page 9: Interior Features
TransPort ® WR41 Utility Installation Guide 3.2 Interior Features 1. Primary Cellular Antenna Cable 2. Secondary Cellular Antenna Cable 3. SIM Slot 4. Ethernet Switch 5. RS232 (RJ45) Connector 6. Battery Mounting Bracket 7. Protected Bonding Ground 8. AC Wiring Terminal Block/Protected Earth Ground (PE) 9. -
Page 10: Mounting
Altitude maximum: 2000 meters (6561 ft.) 4.1 Cable Installation The RJ45 connector in the TransPort WR41 Utility is pre-wired to be straight through to the RS232 connection. Note: If you require an RS232 connection you must provide your own cable. -
Page 11: Installation
In both cases, the end of the SIM card with the chamfered corner should be inserted first. The TransPort WR41 Utility also allows for dual network installations where one wireless service can be used as a back-up in the event that the primary service fails. These installations cannot be used to access two networks simultaneously. -
Page 12: Connect Antenna(S)
If this is the case, Digi has many antenna options to chose from -- please contact us or visit www.digi.com. If antennas other than the supplied antenna(s) are used, the separation between the two should be no less than eight inches (8”). -
Page 13: Connect Power
TransPort ® WR41 Utility Installation Guide 5.3 Connect Power Note: It is recommended that an external IEC 61643-series Certified surge protector is to be used with this product. The surge protector should be rated for the operating voltage of the AC Mains circuit that powers the product and have a clamping voltage not exceeding 2500 V. -
Page 14: Battery Installation
TransPort ® WR41 Utility Installation Guide 5.4 Battery Installation WARNING - For all installations: Precautions are needed to avoid risk of electrostatic charge/ discharge. Always practice proper grounding techniques prior to servicing the device. The battery is shipped in a separate cardboard box inside the container. Remove it from its packaging and mount it into the battery slot on the side of the unit using the following instructions: Step 1) Gently insert the battery into the battery mounting bracket as shown. -
Page 15: Device Initialization
Step 4) Connect the remaining end of the battery cable to the battery terminal on the power supply. 5.4.1 Battery Disposal The TransPort WR41 Utility product contains a lead-acid battery. This battery must be recycled after use. Please follow all applicable Federal, State and regional laws dictating proper recycling methods. -
Page 16: Configuration
TransPort ® WR41 Utility Installation Guide 7 Configuration Once the unit has been installed and powered up, it needs to be configured to communicate with the LAN and WAN. Configuration is performed either using the Command Line Interface (CLI) or the Web Interface. The Web Interface (accessed via a web browser e.g. - Page 17 TransPort ® WR41 Utility Installation Guide The Quick Start Wizard is located in the Getting Started section on the Home menu. 7.2.1 Cellular: CDMA If your unit is to be used on a CDMA network, the embedded module must be provisioned on the network before it can make a connection.
- Page 18 Digi’s configuration file. As the mobile account information is stored on the CDMA module, performing a factory reset on the unit will not remove provisioning information from the CDMA module.
-
Page 19: Command Line Interface (Cli)
TransPort ® WR41 Utility Installation Guide 7.3 Command Line Interface (CLI) In order to configure the unit serially, ensure that the unit is connected to a PC. Also, terminal emulation software (such as HyperTerminal) will be required. 7.3.1 CLI Notes •... - Page 20 (normally this router’s LAN IP address) DHCP 0 MASK x.x.x.x The subnet mask DHCP clients should use DHCP 0 DNS The DNS server DHCP clients should use For more information on CLI commands, visit http://www.digi.com/support/ and view the various reference manuals available. Page 20...
-
Page 21: Troubleshooting
“straight through” RS232 serial cable. This will allow you to change the configuration via the Command Line Interface (CLI). Please refer to the Digi TransPort User Guide for information on how to use the CLI. The User Guide can be downloaded from the Digi Support site. If you have further questions about your product please contact Digi Technical Support (see page 2 for contact information). - Page 22 Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International. Digi provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of fitness or merchantability for a particular purpose. Digi may make improvements and/or changes in this manual or in the product(s) and/or the program(s) described in this manual at any time.
Need help?
Do you have a question about the TransPort WR41 and is the answer not in the manual?
Questions and answers