Go Pump Commercial 3000 Defueler Electronic and Mechanical Dispensers Specification Sheet
Commercial (industrial) volume only display
The "defueler" dispenser operates differently than most suction pump dispensers that you may have
seen in the past, in that it is designed to remove fuel out of a vehicles gas tank and return the fuel to the
underground storage tank. This means that the hose or defueling "wand" is connected to the self
contained pumping units "inlet", and the fuel drawn out of the vehicle passes through the meter and back
to the underground tank through the underground piping. All "defuelers" are self contained (suction
pump) units. There are no remote (submerged pump) models. The "defueler" is available as either the
3700 series electronic or 3100 mechanical dispensers.
This "defueler" is only available in the self contained, single hose, low hose model. There are some
special installation considerations with this type of application, such as, but not limited to:
1) Dispenser requires a double poppeted impact valve
2) Underground tank requires overfill protection and a working vent pipe
See the information contained in this manual for proper installation.
Standard Features
Simple Electronic Computer or Mechanical Non– Computer
Stand-alone or Interfaced to Control Device (Electronic Only)
RS485 interface (Electronic Only)
TM
Exclusive eCal
(Electronic Calibration) Electronic Only)
Magnet activated totals display
Programmable unit of measure for US gallons, liters, or
imperial gallons
Operates from 115/230Vac, 60/50Hz
Self contained (suction) models feature standard 1-HP
continuous duty motor(s)
Back lit LCD displays (Electronic) or Fluorescent Lighting
(Mechanical)
Self-contained (suction) models: single only
Construction
Low Hose Cabinet Design
Side mount nozzle boot
Long-life cabinet construction using galvaneal components
and powder coated panels
Black end panels & top
White dial face covers
Red lower doors (optional colors available)
Hinged swing out lower door
Hinged swing down upper door
Heavy duty hose hook (optional internal spring rewind
retractor available)
Electronic Computer Model
Simple single board design electronics. Includes CPU,
power, display, eCal, RS485 connection, electromechanical
analog totalizer, push-button programming switches, wiring
terminal strip
LED Backlighting board for the LCD display
Optical pulser
Designed for temperature extremes—no heaters or cooling
fans required
Long life, highly visible back lit LCD display, 1" (2.54cm)
numerals
108670 Rev A
Introduction
Electronic Computer (cont'd)
Battery Backup for last sale recall during power outage
(required for resale of fuel)
Simple 2-command protocol via RS485 interface to fleet
management systems supplies pump status, pulses, and
totals
Field wiring goes directly to terminal strip on Computer (for
new installations pull 72" of wire above grade level)
Transaction display of: 999.999 for gallons, 9999.99 for liters
Electronic hose totals of:
99999999.999 for gallons (8.3)
999999999.99 for liters (9.2)
Built-in diagnostics with error codes
Mechanical Computer Model
Mechanical Analog Volume Only Non-Computer
Veeder-Root Electro-Mechanical Reset
Cascade Fluorescent dial face lighting
Unit of Measure for US Gallons, Liters or Imperial Gallons -
Factory Set
Hydraulics
Precision Bennett SB100 Meter, 4-piston, positive
displacement design
Type 75 Bennett sliding vane pumping unit with integral
vortex air eliminator
SB100 meter is electronically calibrated (eCal) on electronic
models. Mechanically calibrated meter on mechanical model.
Suction pumps use a reusable filter
All units feature 1" hose outlets with a 1"x3/4" reducer
bushing
Options
Brushed stainless steel lower doors
Brushed stainless end panels
Custom lower door colors and/or graphics
Mechanical calibration dial for SB100 meter
Explosion proof junction box for lower hydraulic area
E85 alcohol blend compatibility option
Strainer in lieu of filter w/ or w/o cloth sack
4
08/04