Installation; Copper And Fiber Ports; Set The Dip Switches - Transition Networks SBFTF1011-110 User Manual

SBFTF10xx-11x
Part Number Copper - two (2) ports
10Base-T/100Base-TX
SBFTF1029-110 RJ-45
100 m (328 ft)*
SBFTF1029-111 RJ-45
100 m (328 ft)*
SBFTF1029-112 RJ-45
100 m (328 ft)*
SBFTF1029-113 RJ-45
100 m (328 ft)*
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network. (TX) = transmit (RX) = receive
** SBFTF1029-110 and -111 are intended to be installed in the same network
where one is the local converter and the other is the remote converter.
*** SBFTF1029-112 and -113 are intended to be installed in the same network
where one is the local converter and the other is the remote converter.
The chassis version of the media converter is CBFTF10xx-11x. For more
information, see the CBFTF10xx-11x
www.transition.com.

Installation

Copper and Fiber Ports

The figure below illustrates the locations of the two (2) twisted-pair copper ports
and the one (1) fiber port.
Fiber Port 1 (F1)
100Base-FX
2
Tech Support: 1-800-260-1312 International: 00-1-952-941-7600 (24 hours)
Fiber-Optic - one (1) ports
Single Fiber
SC, 1310 nm (TX)/1550 nm (RX)
single mode, 20 km (12.4 miles
SC, 1550 nm (TX)/1310 nm (RX)
single mode, 20 km (12.4 miles)*
SC, 1310 nm (TX)/1550 nm (RX)
single mode, 40 km (24.8 miles)*
SC, 1550 nm (TX)/1310 nm (RX)
single mode, 40 km (24.8 miles)*
user's guide
on-line
Twisted-Pair Twisted-Pair
Port 1 (TP1) Port 2 (TP2)
10/100TX 10/100TX
Installation

Set the Dip Switches

The dip switches are located on the side of the media converter. Use a small,
flat-blade screwdriver or a similar device to set each dip switch.
"SW1" switches 1 - 6
Dip switches 1, 2, and 3 apply only to twisted-pair copper port 1 (TP1).
Dip switch 4 applies to fiber port 1 (F1).
Dip switches 5 and 6 apply to both twisted-pair copper ports (TP1 and TP2).
"Config. Switches" 1 - 4
Dip switches 1, 2, 3, and 4 apply only to twisted-pair copper port 2 (TP2).
NOTE: Switches 1, 2, and 3 apply only to twisted-pair copper port 1 (TP1).
1. Twisted-Pair Auto-Negotiation
UP (Enabled) - The media converter "advertises"
ALL rate and mode capabilities to the network:
at:
• 100Mb/s full-duplex • 100Mb/s half-duplex,
• 10Mb/s full-duplex
DOWN (Disabled) - The bridging media converter
does not "advertise" the rate and mode capabilities
to the network. Switches 2 and 3 are then used to
set the twisted-pair rate and mode.
2. Twisted-Pair Rate
UP (100Base-TX) - Sets the twisted-pair rate to
100Base-TX.
DOWN (10Base-T) - Sets the twisted-pair rate to
10Base-T.
3. Twisted-Pair Mode
UP (Full-Duplex) - The twisted-pair cable distances
are constrained by the cable requirements (see
pages 1 and 2).
DOWN (Half-Duplex): - The twisted-pair cable
distances are constrained by the 512-Bit Rule (see
page 9).
techsupport@transition.com -- Click the "Transition Now" link for a live Web chat.
-- Continued
1
Twisted-Pair Auto-Negotiation ON
• 10Mb/s half-duplex.
Twisted-Pair Auto-Negotiation OFF
Twisted-pair 100Base-TX
Twisted-pair 10Base-T
Twisted-pair Full-Duplex
Twisted-pair Half-Duplex
UP
DOWN
2
2
UP
DOWN
3
UP
DOWN
3