Specifications - Optex ELITE PRO Instruction Manual

Specifications

Door in use
Product lineup
Usage location
Mounting location
Supply voltage
Power consumption
Detection method
Detection area
Detection angle adjustments
Operation indicator
Settings
Wi-Fi
Input specifications
Output specifications
Mounting height
Minimum door speed
Response time
Operating temperature
Protection class
Color
Weight
FCC and ISED Statement
This device complies with part 15 of FCC Rules and Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d'Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
NOTE NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC NOTICE
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
FCC/ISED Radiation Exposure Statement
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency
(RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy.
Cet équipement est conforme aux limites d'exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les
radioélectriques (RF) de la FCC lignes directrices d'exposition et d'exposition aux fréquences radioélectriques (RF) CNR-102 de l' ISDE puisque
cet appareil a une niveau tres bas d'energie RF.
• iPhone is registered trademarks of Apple Inc.
• Android is registered trademarks of Google LLC.
• Wi-Fi is registered trademarks of Wi-Fi Alliance.
Manufacturer
OPTEX Co.,LTD.
5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: +81(0)77-579-8700
FAX.: +81(0)77-579-7030
WEBSITE:
www.optex.net
24
Swing type automatic doors
ELITE PRO (OA-607 T × 2, OC-907C T × 1): For Double Low Energy or Single Full Energy
ELITE PRO2 (OA-607 T × 4, OC-907C T × 1): For Double Full Energy
ELITE PRO LE (OA-607 T × 1, OC-907C T × 1): For Single Low Energy
OA-607 T: Indoors, semi-outdoors
OC-907C T: Indoors
OA-607 T: Door mount
OC-907C T: Inside transom
12 to 30 VDC
OA-607 T: 1.0 W or less
OC-907C T: 3.0 W or less
OC × 1 + OA × 4: 5.5 W or less
Active infrared reflection (Presence detection type)
Threshold area: 8 lines × 1 row
Swing area: 8 lines × 2 and 3 rows
Threshold area: -5 to +5° (inside and outside)
Swing area: ±5˚ (inside and outside)
See Indicator confirmation.
Browser setting tool
Dipswitches
802.11 b/g/n
Test input: Optocoupler voltage 5 to 30 VDC, current 6 mA max. (30 VDC), no polarity
BodyGuard input or motor voltage input: 5 to 160 VDC, 5 to 115 VAC, no polarity
Knowing act input: Dry contact input
Close switch input: Dry contact input
Activation output: Form A relay 50 V, 0.3 A (Resistance load)
Stall output: Form B relay 50 V, 0.3 A (Resistance load)
6'7" to 8'2" (2.0 to 2.5 m)
2°/s
< 0.3 s
-4 to 131°F (-20 to +55°C)
OA-607 T: IP44
OC-907C T: IP40
OA-607 T: Black
OC-907C T: White
OA-607 T: 8.2 oz (230 g)
OC: 3.7 oz (105 g)
North and South America Subsidiary
OPTEX INCORPORATED
18730 S. Wilmington Avenue, Suite 100
Rancho Dominguez CA 90220 U.S.A
TEL.: +1-800-877-6656
FAX.: +1(310)898-1098
WEBSITE: www.ot-inc.com
East coast office
8510 McAlpines Park Drive, Suite 108
Charlotte, NC 28211 U.S.A.
TEL.: +1-800-877-6656
FAX.: +1(704)365-0818
WEBSITE: www.ot-inc.com