Table Of Contents - Minelab MANTICORE Instruction Manual

Table of Contents

Contents3
Getting Started5
Assembly6
Attach The Coil6
Extend The Shafts6
Attach The Armrest6
Quick Start7
Turn On7
Select A Search Mode7
Noise Cancel7
Overview8
Parts Of The Detector9
Screen Protector Application9
Controls10
Charge Status Led10
Power10
Backlight/Lighting10
Screens11
The Detect Screen11
The Settings Menu11
The Status Bar12
Search Mode12
Favourite Mode12
Large Metal Overload Indicator12
Batteries And Charging13
Charger Information And Safety13
Charging The Battery13
Battery Level Indication14
Automatic Shut-Down14
Operating With A Power Bank14
Battery Maintenance14
Search Modes15
Introduction To Search Modes16
Choosing The Right Search Mode16
All-Terrain16
Beach16
General17
Fast17
Low Conductors17
High Conductors17
Goldfield19
Detect Screen Settings20
Sensitivity21
Extreme Sensitivity Settings21
Adjusting The Sensitivity Level21
When To Adjust Sensitivity21
Depth Indicator22
Target Identification, Pinpointing & Recovery23
Target Id Number24
Target Id Number Overview24
Target Id Types24
Ferrous Target Ids24
Typical Target Examples25
Accuracy Factors25
Frequency — Multi-Iq+ Benefit25
Overlapping Or Adjacent Targets25
Id Map26
Elements Of The Id Map26
Single Frequency Id Map26
Target Trace26
Interpreting The Target Trace27
Target Trace Examples27
Coins27
Pull Tabs (And Large Aluminium Foil)27
Bottle Caps28
Nails28
Ground Signal28
Electromagnetic Interference (Emi)29
Large Or Complex Ferrous Objects29
Non-Ferrous Objects Masked By Nearby Iron29
Coin Buried Deep In Mineralised Ground29
Pinpointing30
Pinpointing Methods30
Pinpoint Mode30
The Pinpoint Bar30
Locate A Target Manually31
General Settings32
Vibration33
Turn Vibration On/Off33
Lighting34
Open The Lighting Menu34
Display Backlight34
Flashlight34
Soft Keys35
Soft Key Actions35
Assign The Soft Keys35
Reset36
Factory Reset36
Reset Via The Settings Menu36
Reset Via The Power Button36
Settings Menu37
Frequency38
Frequencies And Search Modes38
Change The Frequency38
Multi-Iq+ Operation38
Single Frequency Operation39
Audio Theme40
Choosing An Audio Theme40
Normal40
Enhanced41
Prospecting41
Depth41
The Depth Theme Pitch Settings41
Profile42
Threshold Level And Pitch42
Change The Profile42
Adjust The Threshold Level/Pitch42
'Reference' Threshold Tone43
'True' Threshold Tone43
Reference Threshold Blanking43
Target Tones44
Choosing A Target Tones Setting44
Single Pitch Settings44
Variable Pitch Settings44
The Target Tones Editor45
Adjust The Width/Pitch Of Tone Regions45
Adjust The Volume Of Tone Regions45
Ferrous Tones46
Ferrous Volume46
Adjusting Ferrous Volume46
Ferrous Pitch46
Ferrous Limits47
Upper And Lower Limits47
Lower Limits47
Ferrous Limits Audio48
Select The Preset Ferrous Limits48
Preset Ferrous Limits48
Copy Preset Limits To Custom49
Edit Custom Ferrous Limits49
Custom Ferrous Limits Editor49
Edit Ferrous Limits For Specific Targets50
Edit Ferrous Limits To Find 'Good' Ferrous Targets50
Edit Ferrous Limits To Reject Difficult Ferrous Targets51
Discrimination Pattern52
Edit A Discrimination Pattern52
The Discrimination Pattern Editor52
Accept / Reject An Id Upon Detection53
Reject A Target Upon Detection53
All Metal53
Enable All Metal53
Recovery Speed54
Recovery Speed And Adjacent Targets54
Swing Rate54
Adjust The Recovery Speed54
Ground Balance55
Auto Ground Balance55
Auto Ground Balance Procedure55
Manual Ground Balance56
Tracking Ground Balance56
Turn Tracking Ground Balance On/Off56
Manual Ground Balance Procedure56
Auto Noise Cancel57
Auto Noise Cancel Procedure57
Continuous Auto Noise Cancel58
Manual Noise Cancel58
Continuous Auto Noise Cancel Procedure58
Manual Noise Cancel Procedure58
Change The Search Mode59
Set The Favourite Search Mode59
Reset A Search Mode60
Search Mode Information60
View Search Mode Information60
Volume61
Adjust The Volume61
Detector Audio62
Wireless Headphones63
Ml 105 Wireless Headphones63
Re-Connect Previously Paired Headphones63
The Wireless Audio Indicator63
Wired Headphones64
Connect Waterproof Headphones64
Connect Wired Headphones64
Headphone Socket Submersion64
Troubleshooting & Errors65
Solving Noise66
Identifying The Source Of Noise66
Targets66
Ground Noise66
General Troubleshooting67
Erratic/Excessive Noise67
No Sound – Wired Headphones67
No Sound – Ml 105 Wireless Headphones67
Speaker Is Squeaky Or Muffled After Submersion In Cold Water68
Headphone Icon Is On, But No Headphones Are Connected68
Errors69
Critically Low Battery Error69
Coil Disconnected Error69
Software Update Failed Error69
Wireless Software Update Error70
Large Metal Overload70
Internal Error70
Safety, Care & Maintenance71
Detector Care And Safety72
General Care And Safety72
Maintenance Of Parts73
Tightening The Camlocks73
After Beach/Saltwater Detecting73
Removing Sand From The Detector73
Specifications, Presets & Compliance74
Technical Specifications75
Software Updates76
View Detector Software Info76
Default Settings78