Mains Supply; Intermittent (3X380-440 V) [A]; Intermittent (3X441-480 V) [A] - Danfoss VLT AQUA FC 202 Design Manual

VLT® AQUA Drive FC 202
Design Guide
Type designation
Intermittent (60 s overload) (3x525–
550 V) [A]
Continuous (3x551–690 V) [A]
Intermittent (60 s) (3x551–690 V) [A]
Continuous kVA at 550 V [kVA]
Continuous kVA at 690 V [kVA]
Maximum input current
Continuous 550 V [A]
Intermittent (60 s overload) (3x525–
550 V) [A]
Continuous (3x551–690 V) [A]
Intermittent (3x551–690 V) [A]
Additional specifications
Maximum cable cross–section for mains
2
and motor [mm (AWG)]
Maximum cable cross–section for brake
2
and load sharing [mm (AWG)]
Maximum cable cross–section
2
mains disconnect [mm (AWG)]
Estimated power loss at rated maxi-
(4)
mum load [W]
(5)
Efficiency
(6)
Enclosure sizes for N75K, N90K are D3h for IP20/Chassis, and D5h for IP54/Type 12.
1
High overload=150% or 160% torque for a duration of 60 s. Normal overload=110% torque for a duration of 60 s.
2
The 3 values for the maximum cable cross-section are for single core, flexible wire, and flexible wire with sleeve, respectively.
3
Applies for dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses may increase. LCP and
4
typical control card power consumptions are included. For more detailed efficiency values and part load losses according IEC/EN 61800-9-2 refer to
mydrive ecosmart on www. danfoss.com. For efficiency class see
Efficiency measured at nominal current. For more detailed efficiency values and part load losses according IEC/EN 61800-9-2 refer to mydrive ecos-
5
mart on www. danfoss.com. For efficiency class see
Measured using 5 m (16 ft) shielded motor cables at rated load and rated frequency. For more detailed efficiency values and part load losses ac-
6
cording IEC/EN 61800-9-2 refer to mydrive ecosmart on

8.2 Mains Supply

Supply terminals
Supply voltage
(1)(2)
Supply voltage
(1)(2)
Supply voltage
(1)(2)
Supply frequency
(3)
Maximum imbalance temporary between mains phases
True power factor (λ)
Danfoss A/S © 2020.09
P37K P45K
54 47.3 64.5
34 41 41
51 45.1 61.5
34.3 41 41
40.6 49 49
36 49 49
54 53.9 72
36 48 48
54 52.8 72
150 (300 MCM)
95 (3/0)
for 95 (3/0)
(3)
600 740 740
0.98
8.4.1
8.4.1 Environment.
www. danfoss.com. For efficiency class see
P55K P75K
59.4 81 71.5 97.5
52 52 62 62
57.2 78 68.2 93
51.4 51.4 61.9 61.9
62.1 62.1 74.1 74.1
59 59 71 71
64.9 87 78.1 105
58 58 70 70
63.8 87 77 105
185, 150, 120 (350 MCM,
300 MCM, 4/0)
900 900 1100 1100
Environment.
8.4.1
Specifications
P90K/N90K
(1)
95.7 130.5
83 83
91.3 124.5
82.9 82.9
99.2 99.2
87 87
95.7 129
86 –
94.6 –
–
1500 1500
Environment.
200–240 V ±10%
380–480 V/500–600 V ±10%
525–600 V ±10%
3.0% of rated supply voltage
≥0.9 nominal at rated load
AJ300847815559en-000101 / 130R0337 | 89
(1)
115.5
100
110
100
119.5
99
108.9
–
–
1800
L1, L2, L3
47.5–63 Hz